Microstructure and Mechanical Properties of Face‐Centered‐Cubic‐Based Cr‐Free Equiatomic High‐Entropy Alloys

2020 ◽  
pp. 2000848
Author(s):  
Xinwang Liu ◽  
Peng Liu ◽  
Weibin Zhang ◽  
Qiang Hu ◽  
Qiang Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Microstructure And Mechanical Properties ◽  
Face Centered

Microstructure and Mechanical Properties of the W-Ni-Co System Refractory High-Entropy Alloys

2015 ◽  
Vol 816 ◽  
pp. 324-329 ◽  
Author(s):  
Hui Jiang ◽  
Li Jiang ◽  
Yi Ping Lu ◽  
Tong Min Wang ◽  
Zhi Qiang Cao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Vacuum Arc ◽  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Melting Temperatures ◽  
Arc Melting ◽  
Microstructure And Mechanical Properties ◽  
The Matrix ◽  
Face Centered

The elements Mo, Cr and V were added to the W-Ni-Co system high entropy alloys, the effects of these added elements on microstructure and mechanical properties of these alloys were studied. The alloys were produced by vacuum arc melting. The compositions were W0.5Ni2Co2VMo0.5,W0.5Ni2Co2VCr0.5and W0.5Ni2Co2CrMo0.5(denoted as Alloy 1, Alloy 2 and Alloy 3) respectively. The theoretical melting temperatures were higher than 2000 K. X-ray diffraction, SEM and energy dispersive spectroscopy (EDS) results indicated that the matrix of the alloys is face-centered cubic (FCC) solid-solution, the alloys showed dendrite crystal structure. Ni, Co elements were enriched in the dendrite areas, the W, Mo were enriched in the inter-dendrite regions ,while V, Cr elements were uniform distribution. The Vickers hardness of these alloys was 376.1 HV, 255.88 HV and 306.8 HV, respectively. The yield strength values (σ0.2) of Alloy 1, Alloy 2 and Alloy 3 were approximately 1000MPa, 750MPa, 250MPa, respectively. The alloys show good compression plasticity deformation capacity at RT.

scholarly journals Effects of Different Contents of Each Component on the Structural Stability and Mechanical Properties of Co-Cr-Fe-Ni High-Entropy Alloys

2021 ◽  
Vol 11 (6) ◽  
pp. 2832
Author(s):  
Haibo Liu ◽  
Cunlin Xin ◽  
Lei Liu ◽  
Chunqiang Zhuang
Keyword(s):  
Mechanical Properties ◽  
Structural Stability ◽  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
Obvious Effect ◽  
High Entropy ◽  
Precise Control ◽  
Component Content ◽  
Face Centered ◽  
And Performance

The structural stability of high-entropy alloys (HEAs) is closely related to their mechanical properties. The precise control of the component content is a key step toward understanding their structural stability and further determining their mechanical properties. In this study, first-principle calculations were performed to investigate the effects of different contents of each component on the structural stability and mechanical properties of Co-Cr-Fe-Ni HEAs based on the supercell model. Co-Cr-Fe-Ni HEAs were constructed based on a single face-centered cubic (FCC) solid solution. Elemental components have a clear effect on their structure and performance; the Cr and Fe elements have an obvious effect on the structural stability and equilibrium lattice constant, respectively. The Ni elements have an obvious effect on stiffness. The Pugh ratios indicate that Cr and Ni addition may increase ductility, whereas Co and Fe addition may decrease it. With increasing Co and Fe contents or decreasing Cr and Ni contents, the structural stability and stiffness of Co-Cr-Fe-Ni HEAs are improved. The structural stability and mechanical properties may be related to the strength of the metallic bonding and covalent bonding inside Co-Cr-Fe-Ni HEAs, which, in turn, is determined by the change in element content. Our results provide the underlying insights needed to guide the optimization of Co-Cr-Fe-Ni HEAs with excellent mechanical properties.

Mechanical properties of high-entropy alloys with emphasis on face-centered cubic alloys

2019 ◽  
Vol 102 ◽  
pp. 296-345 ◽  
Author(s):  
Zezhou Li ◽  
Shiteng Zhao ◽  
Robert O. Ritchie ◽  
Marc A. Meyers
Keyword(s):  
Mechanical Properties ◽  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Face Centered

Synergetic effect of Si addition on mechanical properties in face-centered-cubic high entropy alloys: A first-principles study

2021 ◽  
Author(s):  
T Tsuru ◽  
Ivan Lobzenko ◽  
Daixiu Wei
Keyword(s):  
Mechanical Properties ◽  
First Principles ◽  
Stacking Fault ◽  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Si Doped ◽  
Face Centered ◽  
Si Addition ◽  
Strength And Ductility

Abstract High-entropy alloys (HEA) have been receiving increased attention for their excellent mechanical properties. Our recent study revealed that Si-doped face-centered cubic (FCC) HEAs have great potential to improve both strength and ductility. Here, we carried out first-principles calculations in cooperation with Monte Carlo simulation and structural factor analysis to explore the effect of Si addition on the macroscopic mechanical properties. As a result, Si addition increased the local lattice distortion and the stacking fault energy. Furthermore, the short-range order formation in Si-doped alloy caused highly fluctuated stacking fault energy. Thus, the heterogeneous solid solution states in which low and high stacking fault regions are distributed into the matrix were nucleated. This unique feature in Si-doped FCC-HEA induces ultrafine twin formation in Si-doped alloys, which can be a dominant factor in improving both strength and ductility.

Powder plasma arc additive manufactured CoCrFeNi(SiC)x high-entropy alloys: Microstructure and mechanical properties

2021 ◽  
Vol 282 ◽  
pp. 128736 ◽  
Author(s):  
Qingkai Shen ◽  
Xiangdong Kong ◽  
Xizhang Chen ◽  
Xukai Yao ◽  
Vladislav B. Deev ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Entropy Alloys ◽  
Plasma Arc ◽  
High Entropy ◽  
Microstructure And Mechanical Properties

scholarly journals Development of Novel Lightweight Al-Rich Quinary Medium-Entropy Alloys with High Strength and Ductility

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4223
Author(s):  
Po-Sung Chen ◽  
Yu-Chin Liao ◽  
Yen-Ting Lin ◽  
Pei-Hua Tsai ◽  
Jason S. C. Jang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Compressive Strain ◽  
High Strength ◽  
Fine Tuning ◽  
Face Centered Cubic ◽  
Transportation Industry ◽  
High Entropy ◽  
Good Potential ◽  
Face Centered

Most high-entropy alloys and medium-entropy alloys (MEAs) possess outstanding mechanical properties. In this study, a series of lightweight nonequiatomic Al50–Ti–Cr–Mn–V MEAs with a dual phase were produced through arc melting and drop casting. These cast alloys were composed of body-centered cubic and face-centered cubic phases. The density of all investigated MEAs was less than 5 g/cm3 in order to meet energy and transportation industry requirements. The effect of each element on the microstructure evolution and mechanical properties of these MEAs was investigated. All the MEAs demonstrated outstanding compressive strength, with no fractures observed after a compressive strain of 20%. Following the fine-tuning of the alloy composition, the Al50Ti20Cr10Mn15V5 MEA exhibited the most compressive strength (~1800 MPa) and ductility (~34%). A significant improvement in the mechanical compressive properties was achieved (strength of ~2000 MPa, strain of ~40%) after annealing (at 1000 °C for 0.5 h) and oil-quenching. With its extremely high specific compressive strength (452 MPa·g/cm3) and ductility, the lightweight Al50Ti20Cr10Mn15V5 MEA demonstrates good potential for energy or transportation applications in the future.

Insights into Defect-Mediated Nucleation of Equilibrium B2 Phase in Face-Centered Cubic High-Entropy Alloys

JOM ◽  
2021 ◽  
Author(s):  
Abhishek Sharma ◽  
Bharat Gwalani ◽  
Sriswaroop Dasari ◽  
Deep Choudhuri ◽  
Yao-Jen Chang ◽  
...  
Keyword(s):  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
B2 Phase ◽  
Face Centered

Microstructure and Mechanical Properties of VTaTiMoAlx Refractory High Entropy Alloys

2017 ◽  
Vol 898 ◽  
pp. 638-642 ◽  
Author(s):  
Dong Xu Qiao ◽  
Hui Jiang ◽  
Xiao Xue Chang ◽  
Yi Ping Lu ◽  
Ting Ju Li
Keyword(s):  
Mechanical Properties ◽  
Vacuum Arc ◽  
High Entropy Alloys ◽  
X Ray Diffraction ◽  
Dendrite Structure ◽  
X Ray ◽  
High Entropy ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Microstructure And Mechanical Properties

A series of refractory high-entropy alloys VTaTiMoAlx with x=0,0.2,0.6,1.0 were designed and produced by vacuum arc melting. The effect of added Al elements on the microstructure and mechanical properties of refractory high-entropy alloys were investigated. The X-ray diffraction results showed that all the high-entropy alloys consist of simple BCC solid solution. SEM indicated that the microstructure of VTaTiMoAlx changes from equiaxial dendritic-like structure to typical dendrite structure with the addition of Al element. The composition of different regions in the alloys are obtained by energy dispersive spectroscopy and shows that Ta, Mo elements are enriched in the dendrite areas, and Al, Ti, V are enriched in inter-dendrite areas. The yield strength and compress strain reach maximum (σ0.2=1221MPa, ε=9.91%) at x=0, and decrease with the addition of Al element at room temperature. Vickers hardness of the alloys improves as the Al addition.

Sign in / Sign up

Export Citation Format

Share Document