Effect of Weld Line Direction on Tensile Deformation Behavior

2018 ◽  
Vol 59 (694) ◽  
pp. 209-214
Author(s):  
Masahiro SAITO ◽  
Yoshiaki NAKAZAWA ◽  
Kenichiro OTSUKA ◽  
Masanori YASUYAMA ◽  
Masatoshi TOKUNAGA ◽  
...  
Keyword(s):  
Deformation Behavior ◽  
Tensile Deformation ◽  
Weld Line ◽  
Tensile Deformation Behavior ◽  
Line Direction

scholarly journals Study on Microstructure and In Situ Tensile Deformation Behavior of Fe-25Mn-xAl-8Ni-C Alloy Prepared by Vacuum Arc Melting

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 814
Author(s):  
Yaping Bai ◽  
Meng Li ◽  
Chao Cheng ◽  
Jianping Li ◽  
Yongchun Guo ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
Austenite Phase ◽  
Vacuum Arc ◽  
Al Content ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Tensile Deformation Behavior

In this study, Fe-25Mn-xAl-8Ni-C alloys (x = 10 wt.%, 11 wt.%, 12 wt.%, 13 wt.%) were prepared by a vacuum arc melting method, and the microstructure of this series of alloys and the in situ tensile deformation behavior were studied. The results showed that Fe-25Mn-xAl-8Ni-C alloys mainly contained austenite phase with a small amount of NiAl compound. With the content of Al increasing, the amount of austenite decreased while the amount of NiAl compound increased. When the Al content increased to 12 wt.%, the interface between austenite and NiAl compound and austenitic internal started to precipitate k-carbide phase. In situ tensile results also showed that as the content of Al increased, the alloy elongation decreased gradually, and the tensile strength first increased and then decreased. When the Al content was up to 11 wt.%, the elongation and tensile strength were 2.6% and 702.5 MPa, respectively; the results of in situ tensile dynamic observations show that during the process of stretching, austenite deformed first, and crack initiation mainly occurred at the interface between austenite and NiAl compound, and propagated along the interface, resulting in fracture of the alloy.

The effect of strain rates on tensile deformation of ultrafine-grained copper

2017 ◽  
Vol 31 (16-19) ◽  
pp. 1744014
Author(s):  
M. Li ◽  
Q. W. Jiang
Keyword(s):  
Strain Rate ◽  
Deformation Behavior ◽  
Room Temperature ◽  
Tensile Deformation ◽  
Strain Rates ◽  
Roll Bonding ◽  
Fracture Elongation ◽  
Tensile Deformation Behavior ◽  
Ultrafine Grained ◽  
Flow Stress Level

Tensile deformation behavior of ultrafine-grained (UFG) copper processed by accumulative roll-bonding (ARB) was studied under different strain rates at room temperature. It was found that the UFG copper under the strain rate of 10[Formula: see text] s[Formula: see text] led to a higher strength (higher flow stress level), flow stability (higher stress hardening rate) and fracture elongation. In the fracture surface of the sample appeared a large number of cleavage steps under the strain rate of 10[Formula: see text] s[Formula: see text], indicating a typical brittle fracture mode. When the strain rate is 10[Formula: see text] or 10[Formula: see text] s[Formula: see text], a great amount of dimples with few cleavage steps were observed, showing a transition from brittle to plastic deformation with increasing strain rate.

Compressive and tensile deformation behavior of consolidated Fe

2008 ◽  
Vol 493 (1-2) ◽  
pp. 226-231 ◽  
Author(s):  
S. Cheng ◽  
W.W. Milligan ◽  
X.-L. Wang ◽  
H. Choo ◽  
P.K. Liaw
Keyword(s):  
Deformation Behavior ◽  
Tensile Deformation ◽  
Tensile Deformation Behavior
Sign in / Sign up

Export Citation Format

Share Document