scholarly journals DESIGN AND CONSTRUCTION OF THE WESTERN BREAKWATER FOR THE OUTER PORT AT PUNTA LANGOSTEIRA (A CORUÑA, SPAIN)

2017 ◽  
pp. 14 ◽  
Author(s):  
Antonio Corredor Molguero ◽  
M. Esther Gómez-Martín ◽  
Enrique Peña ◽  
Josep R. Medina
Keyword(s):  
Design Process ◽  
Double Layer ◽  
Atlantic Coast ◽  
Single Layer ◽  
Significant Problem ◽  
Stability Tests ◽  
Final Design ◽  
New Challenges ◽  
Filter Thickness ◽  
Hydraulic Stability

This paper describes the design process, hydraulic stability tests and construction of the Cubipod® armored Western breakwater at Punta Langosteira (Outer Port of A Coruña, Spain), located on the Atlantic coast of Spain. The environmental, geotechnical, economic and logistic conditions favored randomly-placed Cubipods for single-layer armoring of the trunk. 3D hydraulic stability tests were carried out to validate the final design of the Western Breakwater; two models were tested with single- and double-layer Cubipod armors in the trunk and roundhead, respectively. Single-layer 25- and 30-tonne Cubipod® armors were used for the trunk section and a double-layer 45-tonne Cubipod® armor was used for the roundhead. During this project, new challenges were overcome, such as constructing a transition between single and double-layer armors, and manufacturing and handling of 45-tonne Cubipods. The transition in the armor thickness was solved by modifying the filter thickness under the main armor, to ensure a homogeneous external armor profile. Breakwater construction finished in November 2016 with no significant problem or delay in the original schedule.

scholarly journals Armor Damage of Overtopped Mound Breakwaters in Depth-Limited Breaking Wave Conditions

2021 ◽  
Vol 9 (9) ◽  
pp. 952
Author(s):  
Patricia Mares-Nasarre ◽  
Gloria Argente ◽  
M. Esther Gómez-Martín ◽  
Josep R. Medina
Keyword(s):  
Failure Mode ◽  
Double Layer ◽  
Wave Energy ◽  
Single Layer ◽  
Rear Side ◽  
Breaking Wave ◽  
Wave Zone ◽  
Physical Tests ◽  
Wave Conditions ◽  
Hydraulic Stability

Armor damage due to wave attack is the principal failure mode to be considered when designing conventional mound breakwaters. Armor layers of mound breakwaters are typically designed using formulas in the literature for non-overtopped mound breakwaters in non-breaking wave conditions, although overtopped mound breakwaters in the depth-induced breaking wave zone are common design conditions. In this study, 2D physical tests with an armor slope H/V = 3/2 are analyzed in order to better describe the hydraulic stability of overtopped mound breakwaters with double-layer rock, double-layer randomly-place cube and single-layer Cubipod® armors in depth-limited breaking wave conditions. Hydraulic stability formulas are derived for each armor section (front slope, crest and rear slope) and each armor layer. The front slope of overtopped double-layer rock structures is more stable than the front slope of non-overtopped mound breakwaters in breaking wave conditions. When wave attack increases, armor damage appears first on the front slope, later on the crest and, finally, on the rear side. However, once the damage begins on the crest and rear side, the progression is much faster than on the front slope, because more wave energy is dissipated through the armored crest and rear side.

Cracking at the fold in double layer coated paper: the influence of latex and starch composition

TAPPI Journal ◽  
2019 ◽  
Vol 18 (2) ◽  
pp. 93-99
Author(s):  
SEYYED MOHAMMAD HASHEMI NAJAFI ◽  
DOUGLAS BOUSFIELD, ◽  
MEHDI TAJVIDI
Keyword(s):  
Mechanical Properties ◽  
Double Layer ◽  
Starch Content ◽  
Single Layer ◽  
Double Layers ◽  
Coated Paper ◽  
Coated Papers ◽  
Coating Layers ◽  
Scanned Images ◽  
Packaging Paper

Cracking at the fold of publication and packaging paper grades is a serious problem that can lead to rejection of product. Recent work has revealed some basic mechanisms and the influence of various parameters on the extent of crack area, but no studies are reported using coating layers with known mechanical properties, especially for double-coated systems. In this study, coating layers with different and known mechanical properties were used to characterize crack formation during folding. The coating formulations were applied on two different basis weight papers, and the coated papers were folded. The binder systems in these formulations were different combinations of a styrene-butadiene latex and mixtures of latex and starch for two different pigment volume concentrations (PVC). Both types of papers were coated with single and double layers. The folded area was scanned with a high-resolution scanner while the samples were kept at their folded angle. The scanned images were analyzed within a constant area. The crack areas were reported for different types of papers, binder system and PVC values. As PVC, starch content, and paper basis weight increased, the crack area increased. Double layer coated papers with high PVC and high starch content at the top layer had more cracks in comparison with a single layer coated paper, but when the PVC of the top layer was low, cracking area decreased. No measurable cracking was observed when the top layer was formulated with a 100% latex layer.

Single layer versus double layer suture for anastomosis of the gastrointestinal tract

2009 ◽  
Author(s):  
Alvaro Sanabria ◽  
Gabriel Gomez ◽  
Eduardo Valdivieso ◽  
C Bermudez
Keyword(s):  
Gastrointestinal Tract ◽  
Double Layer ◽  
Single Layer ◽  
Layer Versus

Single layer versus double layer suture for anastomosis of the gastrointestinal tract

2005 ◽  
Author(s):  
Alvaro Sanabria ◽  
Gabriel Gomez ◽  
Eduardo Valdivieso ◽  
C Bermudez
Keyword(s):  
Gastrointestinal Tract ◽  
Double Layer ◽  
Single Layer ◽  
Layer Versus

scholarly journals Electron-phonon interaction in In-induced √7 ×√3 structures on Si(111) from first-principles

2021 ◽  
Author(s):  
I. Yu. Sklyadneva ◽  
Rolf Heid ◽  
Pedro Miguel Echenique ◽  
Evgueni Chulkov
Keyword(s):  
Density Functional Theory ◽  
Double Layer ◽  
First Principles ◽  
Linear Response ◽  
Density Functional ◽  
Single Layer ◽  
Phonon Interaction ◽  
Functional Theory ◽  
Electron Phonon Interaction ◽  
The Density Functional Theory

Electron-phonon interaction in the Si(111)-supported rectangular √(7 ) ×√3 phases of In is investigated within the density-functional theory and linear-response. For both single-layer and double-layer √(7 ) ×√3 structures, it...

scholarly journals A Trial Acoustic Improvement in a Lecture Hall with MPP Sound Absorbers and FDTD Acoustic Simulations

2021 ◽  
Vol 11 (6) ◽  
pp. 2445
Author(s):  
Matteo Cingolani ◽  
Giulia Fratoni ◽  
Luca Barbaresi ◽  
Dario D’Orazio ◽  
Brian Hamilton ◽  
...  
Keyword(s):  
Double Layer ◽  
Speech Intelligibility ◽  
Single Layer ◽  
Lecture Hall ◽  
Full Spectrum ◽  
Metal Printing ◽  
Specific Impedance ◽  
Specific Material ◽  
Acoustic Treatment ◽  
Difference Time

Sound absorbing micro-perforated panels (MPPs) are being increasingly used because of their high quality in terms of hygiene, sustainability and durability. The present work investigates the feasibility and the performance of MPPs when used as an acoustic treatment in lecture rooms. With this purpose, three different micro-perforated steel specimens were first designed following existing predictive models and then physically manufactured through 3D additive metal printing. The specimens’ acoustic behavior was analyzed with experimental measurements in single-layer and double-layer configurations. Then, the investigation was focused on the application of double-layer MPPs to the ceiling of an existing university lecture hall to enhance speech intelligibility. Numerical simulations were carried out using a full-spectrum wave-based method: a finite-difference time-domain (FDTD) code was chosen to better handle time-dependent signals as the verbal communication. The present work proposes a workflow to explore the suitability of a specific material to speech requirements. The measured specific impedance complex values allowed to derive the input data referred to MPPs in FDTD simulations. The outcomes of the process show the influence of the acoustic treatment in terms of reverberation time (T30) and sound clarity (C50). A systematic comparison with a standard geometrical acoustic (GA) technique is reported as well.

scholarly journals Ileo-colic intra-corporeal anastomosis during robotic right colectomy: a systematic literature review and meta-analysis of different techniques

2021 ◽  
Author(s):  
Simone Guadagni ◽  
Matteo Palmeri ◽  
Matteo Bianchini ◽  
Desirée Gianardi ◽  
Niccolò Furbetta ◽  
...  
Keyword(s):  
Double Layer ◽  
Meta Analysis ◽  
Single Layer ◽  
Right Colectomy ◽  
Layer Versus ◽  
Bleeding Rate ◽  
Common Technique ◽  
Technical Details ◽  
Robotic Right Colectomy ◽  
Mechanical Anastomosis

Abstract Purpose Robotic assistance could increase the rate of ileo-colic intra-corporeal anastomosis (ICA) during robotic right colectomy (RRC). However, although robotic ICA can be accomplished with several different technical variants, it is not clear whether some of these technical details should be preferred. An evaluation of the possible advantage of one respect to another would be useful. Methods We conducted a systematic review of literature on technical details of robotic ileo-colic ICA, from which we performed a meta-analysis of clinical outcomes. The extracted data allowed a comparative analysis regarding the outcome of overall complication (OC), bleeding rate (BR) and leakage rate (LR), between (1) mechanical anastomosis with robotic stapler, versus laparoscopic stapler, versus totally hand-sewn anastomosis and (2) closure of enterocolotomy with manual double layer, versus single layer, versus stapled. Results A total of 30 studies including 2066 patients were selected. Globally, the side-to-side, isoperistaltic anastomosis, realized with laparoscopic staplers, and double-layer closure for enterocolotomy, is the most common technique used. According to the meta-analysis, the use of robotic stapler was significantly associated with a reduction of the BR with respect to mechanical anastomosis with laparoscopic stapler or totally hand-sewn anastomosis. None of the other technical aspects significantly influenced the outcomes. Conclusions ICA fashioning during RRC can be accomplished with several technical variants without evidence of a clear superiority of anyone of these techniques. Although the use of robotic staplers could be associated with some benefits, further studies are necessary to draw conclusions.

scholarly journals Numerical Analysis of Bearing Capacity of a Ring Footing on Geogrid Reinforced Sand

Buildings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 68
Author(s):  
Haidar Hosamo ◽  
Iyad Sliteen ◽  
Songxiong Ding
Keyword(s):  
Numerical Analysis ◽  
Bearing Capacity ◽  
Double Layer ◽  
Practical Importance ◽  
Single Layer ◽  
Outer Diameter ◽  
Storage Container ◽  
Reinforced Sand ◽  
Oil Storage ◽  
Ring Footing

A ring footing is found to be of practical importance in supporting symmetrical constructions for example silos, oil storage container etc. In the present paper, numerical analysis was carried out with explicit code FLAC3D 7.0 to investigate bearing capacity of a ring footing on geogrid reinforced sand. Effects of the ratio n of its inner/outer diameter (Di/D) of a ring footing, an optimum depth to lay the geogrid layer were examined. It was found that an intersection zone was developed in soil under inner-side (aisle) of ring footing, contributing to its bearing capacity. Substantial increase of bearing capacities could be realized if ratio n of a ring footing was around 0.6. Numerical results also showed that, bearing capacity of a ring footing could increase significantly if a single-layer geogrid was laid at a proper depth under the footing. Similar contribution was found if a double-layer geogrid was implemented. However, such increases appeared to be rather limited if a triple-layer geogrid or a four-layer geogrid was used. A double-layer geogrid was recommended to increase the bearing capacity of a ring footing; the depth to lay this double-layer geogrid was also discussed.

Sign in / Sign up

Export Citation Format

Share Document