scholarly journals STABILITY OF A SAND BED UNDER BREAKING WAVES

1974 ◽  
Vol 1 (14) ◽  
pp. 45 ◽  
Author(s):  
Ole Secher Madsen
Keyword(s):  
Pressure Gradient ◽  
Surf Zone ◽  
Breaking Waves ◽  
Breaking Wave ◽  
Light Weight ◽  
Loss Of Stability ◽  
Vertical Flow ◽  
Sufficient Magnitude ◽  
The Stability ◽  
Bed Material

The possible effect on the stability of a porous sand bed of the flow induced within the bed during the passage of near-breaking or breaking waves is considered. It is found that the horizontal flow rather than the vertical flow within the bed may affect its stability. An approximate analysis, used in geotechnical computations of slope stability, indicates that a momentary bed failure is likely to occur during the passage of the steep front slope of a near-breaking wave. Experimental results for the pressure gradient along the bottom under near-breaking waves are presented. These results indicate that the pressure gradient is indeed of sufficient magnitude to cause the momentary failure suggested by the theoretical analysis. The loss of stability of the bed material due to the flow induced within the bed itself may affect the amount of material set in motion during the passage of a near-breaking or breaking wave, in particular, in model tests employing light weight bed material. The failure mechanism considered here is also used as the basis for a hypothesis for the depth of disturbance of the bed in the surf zone. The flow induced in a porous bed is concluded to be an important mechanism which should be considered when dealing with the wave-sediment interaction in the surf zone.

scholarly journals TOWARD A SIMPLE MODEL OF THE WAVE BREAKING TRANSITION REGION IN SURF ZONES

1986 ◽  
Vol 1 (20) ◽  
pp. 72 ◽  
Author(s):  
David R. Basco ◽  
Takao Yamashita
Keyword(s):  
Simple Model ◽  
Transition Region ◽  
Surf Zone ◽  
Breaking Waves ◽  
Breaking Wave ◽  
Zone Model ◽  
Similarity Parameter ◽  
Set Up ◽  
Linear Growth Model ◽  
Semi Empirical

Breaking waves undergo a transition from oscillatory, irrotational motion, to highly rotational (turbulent) motion with some particle translation. On plane or monotonically decreasing beach profiles, this physically takes place in such a way that the mean water level remains essentially constant within the transition region. Further shoreward a rapid set-up takes place within the inner, bore-like region. The new surf zone model of Svendsen (1984) begins at this transition point and the new wave there contains a trapped volume of water within the surface roller moving with the wave speed. This paper describes a simple model over the transition zone designed to match the Svendsen (1984) model at the end of the transition region. It uses a simple, linear growth model for the surface roller area development and semi-empirical model for the variation of the wave shape factor. Breaking wave type can vary from spilling through plunging as given by a surf similarity parameter. The model calculates the wave height decrease and width of the transition region for all breaker types on plane or monotonically depth decreasing beaches.

Research and Analysis on the Wave Transformation and Irregular Wave Breaking Criterion on the Shore

2016 ◽  
Vol 858 ◽  
pp. 354-358
Author(s):  
Tao You ◽  
Li Ping Zhao ◽  
Zheng Xiao ◽  
Lun Chao Huang ◽  
Xiao Rui Han
Keyword(s):  
Theoretical Model ◽  
Wave Height ◽  
Wave Breaking ◽  
Surf Zone ◽  
Breaking Waves ◽  
Wave Transformation ◽  
Breaking Wave ◽  
Height Distribution ◽  
Flume Experiments ◽  
Irregular Wave

Within the surf zone which is the region extending from the seaward boundary of wave breaking to the limit of wave uprush, breaking waves are the dominant hydrodynamics acting as the key role for sediment transport and beach profile change. Breaking waves exhibit various patterns, principally depending on the incident wave steepness and the beach slope. Based on the equations of conservation of mass, momentum and energy, a theoretical model for wave transformation in and outside the surf zone was obtained, which is used to calculate the wave shoaling, wave set-up and set down and wave height distributions in and outside the surf zone. The analysis and comparison were made about the breaking point location and the wave height variation caused by the wave breaking and the bottom friction, and about the wave breaking criterion under regular and irregular breaking waves. Flume experiments relating to the regular and irregular breaking wave height distribution across the surf zone were conducted to verify the theoretical model. The agreement is good between the theoretical and experimental results.

scholarly journals MODIFICATION OF WAVE SPECTRA ON THE CONTINENTAL SHELF AND IN THE SURF ZONE

2011 ◽  
Vol 1 (8) ◽  
pp. 2 ◽  
Author(s):  
Charles L. Bretschneider
Keyword(s):  
Continental Shelf ◽  
Shallow Water ◽  
Surf Zone ◽  
Wind Waves ◽  
Wave Spectrum ◽  
Breaking Waves ◽  
Bottom Friction ◽  
Breaking Wave ◽  
Predominant Period ◽  
Significant Period

This paper discusses the problem pertaining to the modification of the wave spectrum over the continental shelf. Modification factors include bottom friction, percolation, refraction, breaking waves, ocean currents, and regeneration of wind waves in shallow water, among other factors. A formulation of the problem is presented but no general solution is made, primarily because of lack of basic data. Several special solutions are presented based on reasonable assumptions. The case for a steep continental shelf with parallel bottom contours and wave crests parallel to the coast and for which bottom friction is neglected has been investigated. For this case it is found that the predominant period shifts toward longer periods. The implication is, for example, that the significant periods observed along the U. S. Pacific coast are longer than those which would be observed several miles westward over deep water. The case for a gentle continental shelf with parallel bottom contour and wave crests parallel to the coast and for which bottom friction is important has also been investigated. For this case it is found that the predominant period shifts toward shorter periods as the water depth decreases. The implication is, for example, that the significant periods observed in the shallow water over the continental shelf are shorter than those which would be observed beyond the continental slope. In very shallow water, because shoaling becomes important, a secondary peak appears at higher periods. The joint distribution of wave heights and wave periods is required in order to determine the most probable maximum breaking wave, which can be of lesser height than the most probable maximum non-breaking wave. In very shallow water the most probable maximum breaking wave which first occurs would be governed by the breaking depth criteria, whereas in deepwater wave steepness can also be a governing factor. It can be expected that in very shallow water the period of the most probable maximum breaking wave should be longer than the significant period; and for deeper water the period of the most probable maximum breaking wave can be less than the significant period.

scholarly journals HYDRODYNAMICS UNDER LARGE-SCALE REGULAR AND BICHROMATIC BREAKING WAVES

2018 ◽  
pp. 90
Author(s):  
Dominic Van der A ◽  
Joep Van der Zanden ◽  
Ming Li ◽  
James Cooper ◽  
Simon Clark ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Large Scale ◽  
Surf Zone ◽  
Experimental Studies ◽  
Breaking Waves ◽  
Irregular Waves ◽  
Small Scale ◽  
Breaking Wave ◽  
Wave Flume ◽  
Cfd Models

Multiphase CFD models recently have proved promising in modelling cross‐shore sediment transport and morphodynamics (Jacobsen et al 2014). However, modelling breaking wave turbulence remains a major challenge for these models, because it occurs at very different spatial and temporal length scales and involves the interaction between surface generated turbulence and turbulence generated in the bottom boundary layer. To an extent these challenges arise from a lack of appropriate experimental data, since most previous experimental studies involved breaking waves at small-scale, and have not permitted investigation of the turbulent boundary layer processes. Moreover, most existing studies have concentrated on regular waves, thereby excluding the flow and turbulence dynamics occurring at wave group time-scales under irregular waves within the surf zone. These limitations motivated a new experiment in the large-scale CIEM wave flume in Barcelona involving regular and irregular waves. The experiment was conducted in May-July 2017 within the HYDRALAB+ Transnational Access project HYBRID.

scholarly journals SURF ZONE WAVE HEATING BY ENERGY DISSIPATION OF BREAKING WAVES

2018 ◽  
pp. 2 ◽  
Author(s):  
Zhangping Wei ◽  
Robert A. Dalrymple
Keyword(s):  
Internal Energy ◽  
Wave Energy ◽  
Water Waves ◽  
Wave Breaking ◽  
Surf Zone ◽  
Current System ◽  
Breaking Waves ◽  
Breaking Wave ◽  
Conservation Of Energy ◽  
Wave Heating

This study investigates surf zone wave heating due to the dissipation of breaking wave energy by using the Smoothed Particle Hydrodynamics method. We evaluate the surf zone wave heating by examining the increase of internal energy of the system, which is computed based on the conservation of energy. The equivalent temperature profile is calculated based on a simple conversion relationship between energy and temperature. We first examine the surf zone wave heating based on long-crested wave breaking over a planar beach, and we consider spilling breaker and weakly plunging breaker. Numerical results show that breaking of water waves in the surf zone increases the internal energy of water body. Furthermore, the dissipation of incident wave energy is fully converted into the internal energy in a thermally isolated system, confirming the energy conservation of the present numerical approach. It is further found that the long-crested wave breaking generates undertow, which transports the generated wave heating from the surf zone to deep waters. We further carry out numerical experiments to examine surf zone wave heating due to short-crested wave breaking over a beach. The internal energy generation mainly follows the isolated wave breakers, and there is a 3D pattern of wave heating due to the complicated wave breaking process and current system. In general, the magnitude of the generated internal energy or temperature by dissipation of breaking wave energy in the surf zone is relatively small. The present study shows that the generated water temperature is in the order of 10^-3 Kelvin for wave breaking over a typical coastal beach.

scholarly journals NEW SUSPENDED SAND CONCENTRATION MODEL FOR BREAKING WAVES

2020 ◽  
pp. 32
Author(s):  
Gabriel Lim ◽  
Ravindra Jayaratne ◽  
Tomoya Shibayama
Keyword(s):  
Sediment Transport ◽  
Surf Zone ◽  
Empirical Relationship ◽  
Breaking Waves ◽  
Transport Processes ◽  
Suspended Sediment Transport ◽  
Breaking Wave ◽  
Reference Concentration ◽  
Process Understanding

Process-based morphodynamic modelling suites (as well as other process-based models) are often considered to be inefficient and unsuitable for simulating medium- to long-term morphodynamics due to the various theoretical (e.g. robustness of sediment transport models) and practical (e.g. computational costs) limitations. In particular, a lack of knowledge of sediment transport processes and how they relate to hydrodynamics makes the application of short-term models to long-term coastal evolution challenging. Even the state-of-the-art coastal area modelling suites (such as Delft3D and MIKE21) consist of relatively simple physics, relying instead on numerous semi-empirical parameterizations, which are often poorly supported by measured data and/or physical process understanding. In particular, suspended sediment transport in the highly turbulent surf zone is poorly modelled under breaking wave conditions. Six existing suspended sand concentration (SSC) models were critically evaluated against four high-resolution datasets with field-scale breaking waves and co-located velocity and concentration measurements over multiple cross-shore zones (shoaling, breaking and inner-surf zones). A new improved concentration model was proposed based on a novel empirical relationship observed between local water depth and reference concentration, as well as latest process understanding and insights.Recorded Presentation from the vICCE (YouTube Link): https://youtu.be/2iBrnXs4b3M

scholarly journals FIELD MEASUREMENTS OF IMPACT PRESSURES IN SURF

1974 ◽  
Vol 1 (14) ◽  
pp. 103
Author(s):  
R.L. Miller ◽  
S. Leverette ◽  
J. O'Sullivan ◽  
J. Tochko ◽  
K. Theriault
Keyword(s):  
Vertical Distribution ◽  
Surf Zone ◽  
Field Measurements ◽  
Breaking Waves ◽  
Breaking Wave ◽  
Vertical Array ◽  
Qualitative Explanation ◽  
The Vertical Distribution ◽  
Plunging Breaker ◽  
Spilling Breaker

Field measurements were made of the vertical distribution of impact pressures exerted by breaking waves. Four distinct types are recognized and compared. These are near-breaking wave, plunging breaker, spilling breaker and post-breaking bore. The measurements were obtained by placing a 6 foot aluminum flat plate, backed by a cylinder in the surf zone, so that the fiat faced the approaching breakers. Five sensors were placed at one foot intervals on the flat. The sensors consisted of strain gage mounted aluminum diaphragms. Results indicated that impact pressure is significantly influenced by breaker type. The bore generated the largest impact pressures, followed in decreasing order by plunging breaker, spilling breaker and near breaking wave. In the vertical array, the largest impact pressures were recorded at or near the top, except for the bore where the reverse occurred. A qualitative explanation is given of various phenomena associated with impact pressures, by considering breaker mechanics.

scholarly journals A NEW 3D ROLLER APPROACH FOR FACING ROTATIONAL SURF ZONE HYDRODYNAMICS

2011 ◽  
Vol 1 (32) ◽  
pp. 50
Author(s):  
Antonino Viviano ◽  
Rosaria Ester Musumeci ◽  
Enrico Foti
Keyword(s):  
Surf Zone ◽  
Numerical Models ◽  
Breaking Waves ◽  
Wave Crest ◽  
Breaking Wave ◽  
Wake Effect ◽  
Highly Nonlinear ◽  
Rotational Momentum ◽  
Definition Of ◽  
Vorticity Transport

A 2DH highly nonlinear Boussinesq-type of model for breaking waves has been developed in order to investigate surf zone hydrodynamics, also in the presence of complex bathymetries. The set of equations includes continuity and rotational momentum equations, coupled with the vorticity transport equation. An appropriate spatial definition of the 3D roller concept, along with an algorithm for accurately tracking the roller position, have been on purposely developed. Several numerical simulations have been carried out for the case of a submerged elliptic shoal. The results have been compared with both experimental data and with the results of other numerical models available in the literature. Finally, the vorticity dynamics under a breaking wave has been analyzed both in time and space, showing that a fairly correct interpretation of the wake effect in the rear part of the wave crest is obtained.

scholarly journals Analysis of Rip Current Characteristics Using Dye Tracking Method

Atmosphere ◽  
2021 ◽  
Vol 12 (6) ◽  
pp. 719
Author(s):  
Hyun Dong Kim ◽  
Kyu-Han Kim
Keyword(s):  
Surf Zone ◽  
Breaking Waves ◽  
Rip Current ◽  
Rip Currents ◽  
Induced Current ◽  
Tracking Method ◽  
Survey Techniques ◽  
Current Characteristics ◽  
Bed Material ◽  
Wave Induced

Rip currents are strong water channels flowing away from the shoreline. They can occur on any shore with breaking waves. Rip currents play a significant role in changing the topography of shallow water regions by transporting large amounts of bed material offshore. Moreover, they pose a significant danger for people living in nearshore zones and surfers and cause hundreds of deaths annually worldwide. Therefore, rip current generation characteristics have been investigated to prevent casualties. In this study, a GPS drifter survey was chosen as the investigation method; however, a few drawbacks were discovered, such as low accuracy due to the GPS drifter becoming trapped in the surf zone. Therefore, drones and dyes were used to overcome the drawbacks of drifter methods. The results of dye tracking and the 3D wave-induced current numerical simulation were compared; the velocity and formation of the rip current were found to be relatively similar. With the technological advancements and invention of new survey equipment, the survey techniques also evolve, and this paper shows that the disadvantages of the GPS-based Lagrangian method can be overcome using a dye-mounted drone, which observes the rip current easily and accurately.

scholarly journals Characteristics of Breaking Wave Forces on Piles over a Permeable Seabed

2021 ◽  
Vol 9 (5) ◽  
pp. 520
Author(s):  
Zhenyu Liu ◽  
Zhen Guo ◽  
Yuzhe Dou ◽  
Fanyu Zeng
Keyword(s):  
Wave Breaking ◽  
Stokes Equations ◽  
Slope Angle ◽  
Wave Force ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Secondary Wave ◽  
Wave Forces ◽  
Breaking Wave ◽  
Breaking Wave Forces

Most offshore wind turbines are installed in shallow water and exposed to breaking waves. Previous numerical studies focusing on breaking wave forces generally ignored the seabed permeability. In this paper, a numerical model based on Volume-Averaged Reynolds Averaged Navier–Stokes equations (VARANS) is employed to reveal the process of a solitary wave interacting with a rigid pile over a permeable slope. Through applying the Forchheimer saturated drag equation, effects of seabed permeability on fluid motions are simulated. The reliability of the present model is verified by comparisons between experimentally obtained data and the numerical results. Further, 190 cases are simulated and the effects of different parameters on breaking wave forces on the pile are studied systematically. Results indicate that over a permeable seabed, the maximum breaking wave forces can occur not only when waves break just before the pile, but also when a “secondary wave wall” slams against the pile, after wave breaking. With the initial wave height increasing, breaking wave forces will increase, but the growth can decrease as the slope angle and permeability increase. For inclined piles around the wave breaking point, the maximum breaking wave force usually occurs with an inclination angle of α = −22.5° or 0°.

Sign in / Sign up

Export Citation Format

Share Document