scholarly journals The New Evaluation Method of Thermal Interface Material Using Non-smooth Plate

2016 ◽  
Vol 52 (8) ◽  
pp. 453-458
Author(s):  
Yasuhiro SAITO ◽  
Takanori KOMURO
Keyword(s):  
Evaluation Method ◽  
Thermal Interface Material ◽  
Thermal Interface ◽  
Smooth Plate

scholarly journals Noncured Graphene Thermal Interface Materials for High-Power Electronics: Minimizing the Thermal Contact Resistance

Nanomaterials ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1699
Author(s):  
Sriharsha Sudhindra ◽  
Fariborz Kargar ◽  
Alexander A. Balandin
Keyword(s):  
Contact Resistance ◽  
High Power ◽  
Thermal Contact Resistance ◽  
Thermal Contact ◽  
Wide Band ◽  
Thermal Interface Material ◽  
Thermal Interface Materials ◽  
Total Thermal Resistance ◽  
Thermal Interface ◽  
Interface Materials

We report on experimental investigation of thermal contact resistance, RC, of the noncuring graphene thermal interface materials with the surfaces characterized by different degree of roughness, Sq. It is found that the thermal contact resistance depends on the graphene loading, ξ, non-monotonically, achieving its minimum at the loading fraction of ξ ~15 wt %. Decreasing the surface roughness by Sq~1 μm results in approximately the factor of ×2 decrease in the thermal contact resistance for this graphene loading. The obtained dependences of the thermal conductivity, KTIM, thermal contact resistance, RC, and the total thermal resistance of the thermal interface material layer on ξ and Sq can be utilized for optimization of the loading fraction of graphene for specific materials and roughness of the connecting surfaces. Our results are important for the thermal management of high-power-density electronics implemented with diamond and other wide-band-gap semiconductors.

Interfacially engineered liquid-phase-sintered Cu–In composite solders for thermal interface material applications

2014 ◽  
Vol 49 (22) ◽  
pp. 7844-7854 ◽  
Author(s):  
J. Liu ◽  
U. Sahaym ◽  
I. Dutta ◽  
R. Raj ◽  
M. Renavikar ◽  
...  
Keyword(s):  
Liquid Phase ◽  
Thermal Interface Material ◽  
Thermal Interface

Thermal conduction characteristics of silicone composites including ultrasonic-treated graphite

2021 ◽  
pp. 002199832110595
Author(s):  
Weontae Oh ◽  
Jong-Seong Bae ◽  
Hyoung-Seok Moon
Keyword(s):  
Thermal Conductivity ◽  
Ultrasonic Treatment ◽  
Thermal Conduction ◽  
Light Emitting Diode ◽  
Thermal Interface Material ◽  
Ultrasonic Power ◽  
Lighting System ◽  
Thermal Interface ◽  
Light Emitting ◽  
Inorganic Oxides

The microstructural change of graphite was studied after ultrasonic treatment of the graphite. When the graphite solution was treated with varying ultrasonic power and time, the microstructure changed gradually, and accordingly, the thermal conductivity characteristics of the composite containing the as-treated graphite was also different with each other. Thermal conductivity showed the best result in the silicone composite containing graphite prepared under the optimum condition of ultrasonic treatment, and the thermal conductivity of the composite improved proportionally along with the particle size of graphite. When the silicone composite was prepared by using a mixture of inorganic oxides and graphite rather than graphite alone, the thermal conductivity of the silicone composite was further increased. A silicone composite containing graphite was used for LED (light emitting diode) lighting system as a thermal interface material (TIM), and the temperature elevation due to heat generated, while the lighting was actually operated, was analyzed.

Characterization of a Liquid-Metal Micro Droplets Thermal Interface Material

2010 ◽  
Author(s):  
Amer M. Hamdan ◽  
Aric R. McLanahan ◽  
Robert F. Richards ◽  
Cecilia D. Richards
Keyword(s):  
Liquid Metal ◽  
Thermal Resistance ◽  
Contact Resistance ◽  
Applied Load ◽  
Thermal Interface Material ◽  
Thermal Interface ◽  
Interface Resistance ◽  
Thermal Interface Resistance ◽  
Droplet Array

This work presents the characterization of a thermal interface material consisting of an array of mercury micro droplets deposited on a silicon die. Three arrays were tested, a 40 × 40 array (1600 grid) and two 20 × 20 arrays (400 grid). All arrays were assembled on a 4 × 4 mm2 silicon die. An experimental facility which measures the thermal resistance across the mercury array under steady state conditions is described. The thermal interface resistance of the arrays was characterized as a function of the applied load. A thermal interface resistance as low as 0.253 mm2 K W−1 was measured. A model to predict the thermal resistance of a liquid-metal micro droplet array was developed and compared to the experimental results. The model predicts the deformation of the droplet array under an applied load and then the geometry of the deformed droplets is used to predict the thermal resistance of the array. The contact resistance of the mercury arrays was estimated based on the experimental and model data. An average contact resistance was estimated to be 0.14 mm2 K W−1.

scholarly journals Thermal Properties of the Graphene Composites: Application of Thermal Interface Materials

2018 ◽  
Vol 7 (4.33) ◽  
pp. 530
Author(s):  
Mazlan Mohamed ◽  
Mohd Nazri Omar ◽  
Mohamad Shaiful Ashrul Ishak ◽  
Rozyanty Rahman ◽  
Zaiazmin Y.N ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermal Contact Resistance ◽  
Thermal Contact ◽  
Matrix Material ◽  
Thermal Interface Material ◽  
Thermal Interface Materials ◽  
Uniform Thickness ◽  
Thermal Interface ◽  
Interface Materials ◽  
Main Material

Epoxy mixed with others filler for thermal interface material (TIM) had been well conducted and developed. There are problem occurs when previous material were used as matrix material likes epoxy that has non-uniform thickness of thermal interface material produce, time taken for solidification and others. Thermal pad or thermal interface material using graphene as main material to overcome the existing problem and at the same time to increase thermal conductivity and thermal contact resistance. Three types of composite graphene were used for thermal interface material in this research. The sample that contain 10 wt. %, 20 wt. % and 30 wt. % of graphene was used with different contain of graphene oxide (GO).  The thermal conductivity of thermal interface material is both measured and it was found that the increase of amount of graphene used will increase the thermal conductivity of thermal interface material. The highest thermal conductivity is 12.8 W/ (mK) with 30 w. % graphene. The comparison between the present thermal interface material and other thermal interface material show that this present graphene-epoxy is an excellent thermal interface material in increasing thermal conductivity.  

scholarly journals Demonstration of a Compliant Micro-Spring Array As a Thermal Interface Material for Pluggable Optoelectronic Transceiver Modules

2019 ◽  
Author(s):  
Jin Cui ◽  
Liang Pan ◽  
Justin A. Weibel
Keyword(s):  
Heat Sink ◽  
Thermal Contact ◽  
Thermal Conductance ◽  
Thermal Interface Material ◽  
Thermal Contact Conductance ◽  
Compression Pressure ◽  
Thermal Interface ◽  
Operation Temperature ◽  
Optical Module ◽  
Dry Contact

Abstract Pluggable optoelectronic transceiver modules are widely used in the fiber-optic communication infrastructure. It is essential to mitigate thermal contact resistance between the high-power optical module and its riding heat sink in order to maintain the required operation temperature. The pluggable nature of the modules requires dry contact thermal interfaces that permit repeated insertion–disconnect cycles under low compression pressures (∼10–100 kPa). Conventional wet thermal interface materials (TIM), such as greases, or those that require high compression pressures, are not suitable for pluggable operation. Here we demonstrate the use of compliant micro-structured TIM to enhance the thermal contact conductance between an optical module and its riding heat sink under a low compression pressure (20 kPa). The metallized and polymer-coated structures are able to accommodate the surface nonflatness and microscale roughness of the mating surface while maintaining a high effective thermal conductance across the thickness. This dry contact TIM is demonstrated to maintain reliable thermal performance after 100 plug-in and plug-out cycles while under compression.

Sign in / Sign up

Export Citation Format

Share Document