scholarly journals Distribution Network Reliability and Efficiency Enhancement Using Distributed Generation

2021 ◽  
pp. 55-71
Author(s):  
Raymond Onyeka Nwajuonye ◽  
Innocent Ifeanyi Okonkwo ◽  
Johnpaul I. Iloh
Keyword(s):  
Distributed Generation ◽  
Reactive Power ◽  
Greenhouse Gas Emission ◽  
Distribution Network ◽  
Load Flow ◽  
Optimal Placement ◽  
Voltage Profile ◽  
Power Sector ◽  
Voltage Limit ◽  
Transmission And Distribution

The Nigerian power sector is faced with many challenges such as: generation deficit, inefficiency and power loss over lengthy transmission and distribution lines, contribution to greenhouse gas emission, weak and dilapidated transmission and distribution infrastructure, dependence on fossil fuels, insufficient power. Efforts should be put in place by relevant authorities to improve the power sector. With the distribution network being the closest to the final consumer, efforts should be made to make it more efficient. This study therefore aims at improving the performance of poor distribution network using Distributed Generation (DG), optimally placed and sized in the network.  The Asaba, 2 X 15MVA, 33/11kV injection substation in Asaba, Delta state of Nigeria consisting of Anwai road feeder and SPC feeder radiating outwardly from this injection substation was the focus of this study. Relevant data collected from Benin Electricity Distribution Company (BEDC) was used to carry out load flow study. The simulation and analysis of the result and injection of photovoltaic (PV) DG of Asaba injection substation distribution network using Newton-Raphson iteration technique in ETAP 12.6environment to ascertain the overall performance of the network under base loading condition was modelled from a drawn detailed single line diagram of the network. DGs were optimally placed in specific buses in the network using loss sensitivity analysis. The result revealed that prior to DG placement in the network, only 10.4% of the buses were within statutory voltage limit (394.25V – 435.75V or 0.95p.u – 1.05p.u) and 89.6% of the load buses in the network violated the statutory voltage limit and high losses (active and reactive) of 1329.08kW and 2031kVar. After the optimal placement of DG, the active and reactive power losses on the network reduced by 57.5% and 70.7%. While the voltage profile improved by 94.8%, thereby increasing the capacity, reliability and efficiency of distribution network.  

Swarm-Intelligence-Based Optimal Placement and Sizing of Distributed Generation in Distribution Network

2018 ◽  
pp. 29-48 ◽  
Author(s):  
Mahesh Kumar ◽  
Perumal Nallagownden ◽  
Irraivan Elamvazuthi ◽  
Pandian Vasant ◽  
Luqman Hakim Rahman
Keyword(s):  
Distributed Generation ◽  
Radial Distribution ◽  
Distribution System ◽  
Voltage Stability ◽  
Reactive Power ◽  
Distribution Network ◽  
Stability Index ◽  
Pso Algorithm ◽  
Distribution Networks ◽  
Optimal Placement

In the distribution system, distributed generation (DG) are getting more important because of the electricity demands, fossil fuel depletion and environment concerns. The placement and sizing of DGs have greatly impact on the voltage stability and losses in the distribution network. In this chapter, a particle swarm optimization (PSO) algorithm has been proposed for optimal placement and sizing of DG to improve voltage stability index in the radial distribution system. The two i.e. active power and combination of active and reactive power types of DGs are proposed to realize the effect of DG integration. A specific analysis has been applied on IEEE 33 bus system radial distribution networks using MATLAB 2015a software.

scholarly journals Loss Minimization of Power Distribution Network using Different Types of Distributed Generation Unit

2015 ◽  
Vol 5 (5) ◽  
pp. 918
Author(s):  
Su Hlaing Win ◽  
Pyone Lai Swe
Keyword(s):  
Power System ◽  
Distributed Generation ◽  
Radial Distribution ◽  
Distribution System ◽  
Reactive Power ◽  
Distribution Network ◽  
Loss Reduction ◽  
Voltage Profile ◽  
Optimum Location ◽  
Power Losses

A Radial Distribution network is important in power system area because of its simple design and reduced cost. Reduction of system losses and improvement of voltage profile is one of the key aspects in power system operation. Distributed generators are beneficial in reducing losses effectively in distribution systems as compared to other methods of loss reduction. Sizing and location of DG sources places an important role in reducing losses in distribution network. Four types of DG are considered in this paper with one DG installed for minimize the total real and reactive power losses. The objective of this methodology is to calculate size and to identify the corresponding optimum location for DG placement for minimizing the total real and reactive power losses and to improve voltage profile   in primary distribution system. It can obtain maximum loss reduction for each of four types of optimally placed DGs. Optimal sizing of Distributed Generation can be calculated using exact loss formula and an efficient approach is used to determine the optimum location for Distributed Generation Placement.  To demonstrate the performance of the proposed approach 36-bus radial distribution system in Belin Substation in Myanmar was tested and validated with different sizes and the result was discussed.

scholarly journals Optimal Placement and Sizing of Distributed Generation in Distribution System using Analytical Method

2019 ◽  
Vol 8 (4) ◽  
pp. 6357-6363
Keyword(s):  
Distributed Generation ◽  
Distribution System ◽  
Power Loss ◽  
Distribution Network ◽  
Optimal Placement ◽  
Small Scale ◽  
Voltage Profile ◽  
Distribution Grid ◽  
Step Size ◽  
System Power

The reliability of distribution network can be improved with the penetration of small scale distributed generation (DG) unit to the distribution grid. Nevertheless, the location and sizing of the DG in the distribution network have always become a topic of debate. This problem arises as different capacity of DG at various location can affect the performance of the entire system. The main objective of this study is to recommend a suitable size of DG to be placed at the most appropriate location for better voltage profile and minimum power loss. Therefore, this paper presents an analytical approach with a fixed DG step size of 500 kW up to 4500 kW DG to analyses the effect of a single P-type DG in IEEE 33 bus system with consideration of system power loss and voltage profile. Four scenarios have been selected for discussions where Scenario 1: 3500 kW DG placed at node 3; Scenario 2: 2500 kW DG placed at node 6; Scenario 3: 1000 kW DG placed at node 18 and Scenario 4: 3000 kW DG placed at node 7. Results show that all the four scenarios are able to reduce the power loss and improve the voltage profile however Scenario 4 has better performance where it complies with minimum voltage requirement and minimizing the system power loss.

scholarly journals Optimal Sizing and Sitting of Distributed Generation for Power Quality Improvement of Distribution Network

2019 ◽  
Vol 4 (10) ◽  
pp. 18-23 ◽  
Author(s):  
Abubakar Bawa ◽  
Muhammad Uthman ◽  
Farouq E. Shaibu ◽  
Koledowo Saliu Oyewale
Keyword(s):  
Adverse Effect ◽  
Power Quality ◽  
Distributed Generation ◽  
Reactive Power ◽  
Distribution Network ◽  
Loss Reduction ◽  
Voltage Profile ◽  
Power Losses ◽  
Optimal Sizing ◽  
Active And Reactive Power

The Point of Common Coupling (PCC) where suppliers’ responsibility and customers demand meet is of great concern due to increase degree of voltage variation assessment; valuable indicator of system conditions (voltage profile). Unstable condition of the power system outside operational or statutory limit, an adverse effect of nonlinear loads usually generate harmonics as well as fundamental frequency voltage variations and increase rate of power losses. These loads need to be compensated for. The major concerns of utility operations is to mitigate adverse effect of this system conditions. This research work focuses on optimal siting and sizing of Distributed Generation (DG) in a 43 bus distribution system. Power losses coupled with voltage deviation, considering objective function that compute present percentage losses in 11kV Dikko feeder, Abuja Electricity Distribution Company (AEDC), Suleja Distribution Network, Nigeria. We identified buses with poor voltage profile without DG installation and determined optimal sizing and siting of DGs where losses can be mitigated and power quality improved. ETAP version 12.6 2014 was used for load flow analysis to establish a decisive based case. The total load of the system considered was (3490 + j2700) kVA. Active and Reactive power losses in the system before DG installation were 246.300 kW and 289.903 kVAR respectively. DGs installation in the case study, has a considerable effects on loss reduction in the network. It is observed that 8.10% and 7.20% active and reactive power loss reduction was achieved while bus voltage improved by 0.4%. Genetic Algorithm Optimization techniques programmed in MATLAB 2015 software was used for optimal placement and sizing of the DG in the system.

scholarly journals Penetration effects of various kinds of distributed generation systems on the distribution system

2019 ◽  
Vol 8 (9) ◽  
pp. 596-600
Keyword(s):  
Distributed Generation ◽  
Radial Distribution ◽  
Distribution System ◽  
Reactive Power ◽  
Load Flow ◽  
Voltage Profile ◽  
Power Losses ◽  
Generation System ◽  
Radial Distribution System ◽  
Real Power

Distributed generation system penetration in the existing distribution system is done for minimizing the losses and improving the voltage profile. There are total five types of distributed generation systems exist based on their power delivery like distributed generation system injecting real and reactive power, supplying real power only, supplying reactive power only, absorbing reactive power only , supplying real power and absorbing reactive power. All these five types of distributed generation systems have different penetration effects on the radial distribution system. We get different voltage profiles and power losses for different types of distributed generation systems. The testing of these five types of distributed generation systems will be done on IEEE 33 bus radial distribution system. For computing, the line parameters and power losses of the above testing system the forward-backward sweep load flow method will be applied

scholarly journals Enhancement of Voltage Profile by Optimal Placement of Distributed Generators with UPFC in Distribution Networks

2019 ◽  
Vol 8 (6) ◽  
pp. 2733-2738 ◽  
Keyword(s):  
Transmission Lines ◽  
Network Reliability ◽  
Distribution Network ◽  
Flow Analysis ◽  
Distribution Networks ◽  
Load Flow ◽  
Optimal Placement ◽  
Voltage Profile ◽  
Load Flow Analysis ◽  
Distributed Generators

The Distributed generation and fast operating power electronic devices are attracting more attention due to their effective solution for improvement in the voltage profile, to meet the increasing power consumption, reduction in the power loss, enhancement in the power transfer capacity of the transmission lines, reducing the overloading of the entire network. The optimal placement of DG and FACTs devices plays key role in improvement of the network reliability and voltage stability. In this paper exhaustive load flow analysis is carried out for optimal placement of DG and UPFC. The proposed method is tested on 40 bus distribution network. The obtained results are satisfactory in terms of improvement in the overall performance of the distribution network.

scholarly journals Optimal sizing and location of distributed generation for loss minimization using firefly algorithm

2019 ◽  
Vol 14 (1) ◽  
pp. 421 ◽  
Author(s):  
Muhamad Najib Kamarudin ◽  
Tengku Juhana Tengku Hashim ◽  
AbdulHamid Musa
Keyword(s):  
Distributed Generation ◽  
Radial Distribution ◽  
Power Distribution ◽  
Firefly Algorithm ◽  
Distribution Network ◽  
Flow Analysis ◽  
Test System ◽  
Load Flow ◽  
Voltage Profile ◽  
Load Flow Analysis

<span>Distributed generation (DG) plays an important role in improving power quality as well as system realibility. As the incorporation of DG in the power distribution network creates several problems to the network operators, locating a suitable capacity and placement for DG will essentially help to improve the quality of power delivery to the end users. This paper presents the simulation of an application of firefly algorithm (FA) for optimally locating the most suitable placement and capacity of distributed generation (DG) in IEEE 33-bus radial distribution network. This strategy aims at minimizing losses together with improving the voltage profile in distribution network. The losses in real power and voltages at each bus are obtained using load flow analysis which was performed on an IEEE 33-bus radial distribution network using forward sweep method.  The proposed method comprises of simulation of the test system with DG as well as in the absence of DG in the system. </span><span>A comparison between the Firefly Algorithm (FA) with Genetic Algorithm (GA) is also demonstrated in this paper. The results obtained have proven that the Firefly Algorithm has a better capability at improving both the voltage profile and the power losses in the system.</span>

scholarly journals Impact of Distributed Generation on a Distribution Network Voltage Sags in Baghdad City

2021 ◽  
Vol 39 (4A) ◽  
pp. 528-542
Author(s):  
Ali H. Mohammed ◽  
Suad I. Shahl
Keyword(s):  
Distributed Generation ◽  
Distribution System ◽  
Distribution Network ◽  
Optimal Placement ◽  
System Modelling ◽  
Voltage Sags ◽  
Voltage Profile ◽  
De Algorithm ◽  
Power Loss Reduction ◽  
Real Coded Genetic Algorithm

Voltage sags are considered as one of the most detrimental power quality (PQ) disturbance due to their costly influence on sensitive loads. This paper investigates the voltage sag mitigation in distribution network following the occurrence of a fault. Two software are used in this work; the 1st is MATLAB R2017a for implementation of the Differential Evaluation (DE) algorithm to find the optimal location and size DG and while the 2nd software is CYME 7.1 for the distribution system modelling and analysis. The effectiveness of the proposed method is tested by implementing it on IEEE 33-bus system, and then it is applied to Al-Masbh distribution network in Baghdad city as a case study. The paper aims to enhance voltage profile, power loss reduction, and relieve distribution lines overloading, by optimal placement of distributed generation (DG). The results indicate the efficiency of the proposed method comparing with Real Coded Genetic Algorithm (RCGA).

scholarly journals Voltage profile enhancement in distribution network using static synchronous compensator STATCOM

2020 ◽  
Vol 10 (4) ◽  
pp. 3367
Author(s):  
Mohammed Yahya Suliman
Keyword(s):  
Distribution System ◽  
Distribution Systems ◽  
Reactive Power ◽  
Fuzzy Controller ◽  
Distribution Network ◽  
Voltage Profile ◽  
Static Synchronous Compensator ◽  
System A ◽  
Facts Devices ◽  
Transmission And Distribution

STATCOM is one of FACTS devices that used as regulator for transmission and distribution systems which works for reactive power compensation. STATCOM utilisation in distribution system mostly for enhancing the profile of voltage, where used for adjusting the disturbance voltage by injecting into the system a controllable voltage. This paper present a Fuzzy controller based on STATCOM to enhance the voltage profile in distribution network. The controller of STATCOM has simulated for different types of abnormal load conditions of balance and unbalance load. The results of simulation show ability of proposed design to enhance the load voltage which was 96% of the nominal value.

Optimal Placement and Sizing of Distributed Generation in Distribution System Using Modified Particle Swarm Optimization Algorithm

2018 ◽  
pp. 485-507 ◽  
Author(s):  
Mahesh Kumar ◽  
Perumal Nallagownden ◽  
Irraivan Elamvazuthi ◽  
Pandian Vasant
Keyword(s):  
Particle Swarm Optimization ◽  
Distributed Generation ◽  
Distribution System ◽  
Reactive Power ◽  
Particle Swarm ◽  
Pso Algorithm ◽  
Optimal Placement ◽  
Voltage Profile ◽  
Swarm Optimization ◽  
Modified Particle Swarm Optimization

The electricity demand, fossil fuel depletion and environment issues increase the interest of power engineers to integrate small power generations i.e. called distributed generation (DGs) in the distribution system. The DG in distribution system has many positive effects such as it reduces the system power losses, improves the voltage profile and strengthen the voltage stability etc. The placement and sizing of DG play a major role in optimizing these parameters. Therefore, this chapter proposes a modified Particle Swarm Optimization (PSO) algorithm for finding the optimal placement and sizing of distributed generation in the radial distribution system. Two types of DGs such as an active power and reactive power DGs are tested on standard IEEE 33 radial bus system. Moreover, it can be realized that proposed method gives very effective results when both of active and reactive power DGs are integrated into the distribution system.

Sign in / Sign up

Export Citation Format

Share Document