scholarly journals Mechanical and Morphological Properties of Poly(acrylonitrile-butadiene-styrene) and Poly(lactic acid) Blends

2011 ◽  
Vol 49 (4) ◽  
pp. 438-442 ◽  
Author(s):  
Yun Kyun Lee ◽  
Ji Mun Kim ◽  
Woo Nyon Kim
Keyword(s):  
Lactic Acid ◽  
Acrylonitrile Butadiene Styrene ◽  
Morphological Properties ◽  
Poly Lactic Acid ◽  
Poly Acrylonitrile ◽  
Butadiene Styrene

scholarly journals Modification of poly(lactic) acid by reactive extrusion and its melt blending with acrylonitrile–butadiene–styrene

2020 ◽  
Vol 69 (9) ◽  
pp. 794-803
Author(s):  
Tobias Abt ◽  
Mohammad Reza Kamrani ◽  
Jonathan Cailloux ◽  
Orlando Santana ◽  
Miguel Sánchez‐Soto
Keyword(s):  
Lactic Acid ◽  
Acrylonitrile Butadiene Styrene ◽  
Reactive Extrusion ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Butadiene Styrene

Recycling of engineering plastics from waste electrical and electronic equipments: Influence of virgin polycarbonate and impact modifier on the final performance of blends

2014 ◽  
Vol 32 (5) ◽  
pp. 379-388 ◽  
Author(s):  
Ramesh V ◽  
Manoranjan Biswal ◽  
Smita Mohanty ◽  
Sanjay K Nayak
Keyword(s):  
Acrylonitrile Butadiene Styrene ◽  
High Impact ◽  
Morphological Properties ◽  
Material Recycling ◽  
Engineering Plastics ◽  
Acrylic Ester ◽  
Blending Process ◽  
Impact Modifier ◽  
Poly Acrylonitrile ◽  
Butadiene Styrene

This study is focused on the recovery and recycling of plastics waste, primarily polycarbonate, poly(acrylonitrile-butadiene-styrene) and high impact polystyrene, from end-of-life waste electrical and electronic equipments. Recycling of used polycarbonate, acrylonitrile-butadiene-styrene, polycarbonate/acrylonitrile-butadiene-styrene and acrylonitrile-butadiene-styrene/high impact polystrene material was carried out using material recycling through a melt blending process. An optimized blend composition was formulated to achieve desired properties from different plastics present in the waste electrical and electronic equipments. The toughness of blended plastics was improved with the addition of 10 wt% of virgin polycarbonate and impact modifier (ethylene-acrylic ester-glycidyl methacrylate). The mechanical, thermal, dynamic-mechanical and morphological properties of recycled blend were investigated. Improved properties of blended plastics indicate better miscibility in the presence of a compatibilizer suitable for high-end application.

scholarly journals Poly(Lactic Acid) (PLA)/Acrylonitrile Butadiene Styrene (ABS) with Graphene Nanoplatelet (GNP) Nanocomposites

2020 ◽  
Vol 20 (2) ◽  
pp. 276 ◽  
Author(s):  
Mohd Bijarimi ◽  
Noor Shahadah ◽  
Azizan Ramli ◽  
Said Nurdin ◽  
Waleed Alhadadi ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Lactic Acid ◽  
Acrylonitrile Butadiene Styrene ◽  
Poly Lactic Acid ◽  
Twin Screw Extruder ◽  
Melt Blending ◽  
Screw Extruder ◽  
Graphene Nanoplatelet ◽  
Twin Screw ◽  
Butadiene Styrene

A melt blending of poly(lactic acid) (PLA)/acrylonitrile-butadiene-styrene (ABS) with 30:70 PLA:ABS was prepared by a twin screw extruder with a die of 25 mm width and 0.5 mm thickness with various loadings of graphene (0–1.0 wt.%). The PLA/ABS blends were evaluated by mechanical, morphology, thermal and interaction of the components of the blend. Results show the incorporation of graphene nanoplatelet (GNP) improved the tensile and modulus properties. Nevertheless, it was observed that at higher GNP loadings i.e. 0.6–1.0 wt.%, both tensile and modulus properties showed a decreasing trend. It was also found that the thermal stability for the blend slightly improved when graphene presence in the blend.

scholarly journals Surface Finishing of 3D-Printed Polymers with Selected Coatings

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2797
Author(s):  
Jure Žigon ◽  
Mirko Kariž ◽  
Matjaž Pavlič
Keyword(s):  
Lactic Acid ◽  
Substrate Surface ◽  
Chemical Properties ◽  
Acrylonitrile Butadiene Styrene ◽  
Surface Finishing ◽  
Poly Lactic Acid ◽  
Coating Film ◽  
3D Printed ◽  
And Chemical Properties ◽  
Butadiene Styrene

Surface treatment of 3D-printed objects with coatings, besides protection against environmental influences, offers the improvement of visual appearance of the printed elements. In order to design an optimum surface system, the physical and chemical properties of polymers surfaces should be well-known. In the present study, 3D-printed samples of acrylonitrile-butadiene-styrene, poly(lactic acid) and poly(lactic acid) with wood flour additive were coated with three different types of coating, namely solvent borne alkyd coating, water borne acrylic coating and coating made of acrylonitrile-butadiene-styrene diluted in acetone. The surface properties of substrates and the properties of surface systems were assessed with different methods. The results revealed the surfaces of polymers having hydrophobic character, whereas the color, gloss, surface roughness and coating film thickness of coated surfaces depend on the characteristics of particular coatings. Finally, the adhesion of coatings was shown to be appropriate, but dependent on substrate surface porosity and chemical properties of both substrate surface and coating asset.

Sign in / Sign up

Export Citation Format

Share Document