scholarly journals Influences of high temperature on mechanical properties of fly ash based geopolymer mortars reinforced with PVA fiber

2021 ◽  
Vol 20 (2) ◽  
pp. 393-406
Author(s):  
Mehmet Kaya ◽  
◽  
Fuat Köksal ◽  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Fly Ash ◽  
High Temperatures ◽  
Physical And Mechanical Properties ◽  
The Other ◽  
Polyvinyl Alcohol Fiber ◽  
Pva Fiber ◽  
High Temperature Effect

In this study, a geopolymer composite containing PVA fiber was produced to recycle waste fly ash and obtain an eco-friendly binder. Mechanical properties of geopolymer mortars, produced by using F class fly ash which was activated with NaOH (sodium hydroxide), and reinforced by PVA (polyvinyl alcohol) fiber were investigated after high temperature effect. Geopolymer mortar samples produced by mixing with fly ash, sand, water and NaOH were placed in standard molds of 40×40×160 mm3. PVA fibers were used at percentages of 0,5%, 1% and 1,5% by volume in the experiment. Tests were performed on mortars exposed to high temperatures of 200°C, 400°C, 600°C and 800°C for physical and mechanical properties. For the specimens not subjected to high temperatures, an increase in the compressive strength of mortars containing PVA fibers was observed in comparison to mortar without PVA fiber. On the other hand, it was concluded that losses in compressive strength were less for mortar without PVA fiber when compared with the mortars containing PVA fibers. As a result of the modeling, the PVA ratio, which gives the optimum flexural and compressive strength, was determined as 1,47%. As a result of melting of PVA fibers under the effect of high temperature, 83,58% loss of compressive strength was determined in samples containing 1,5% PVA after 800ºC temperature.

Research on Barite Concrete Mixed with Fly Ash

2013 ◽  
Vol 275-277 ◽  
pp. 2107-2111
Author(s):  
Qiu Lin Zou ◽  
Jun Li ◽  
Zhen Yu Lai
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Compressive Strength ◽  
High Temperature ◽  
Fly Ash ◽  
Apparent Density ◽  
Cycle Times ◽  
Residual Compressive Strength ◽  
Temperature Performance

Barite concrete with density grade of 3 and strength grade of C30 was prepared by mixing with different fineness of fly ash. The workability, mechanical properties and long-term high temperature performance of the prepared barite concrete were researched. Results show that the workability of barite concrete is improved by mixing with fly ash, and no segregation of mixture has been observed. The apparent density and 3d, 28d compressive strength of barite concrete are decreased obviously after mixing with fly ash. But with the increasing of the fineness of fly ash, the apparent density and 3d, 28d compressive strength of barite concrete have a slight increase. High temperature residual compressive strength is decreased with the increasing of temperature. The cycle times of heat treatment at 400°C only has a little effect on residual compressive strength of barite concrete.

Physical and mechanical characteristics of cement mortars and concretes with addition of clinoptilolite from Beli Plast deposit (Bulgaria), silica fume and fly ash

Clay Minerals ◽  
2011 ◽  
Vol 46 (2) ◽  
pp. 213-223 ◽  
Author(s):  
V. Lilkov ◽  
I. Rostovsky ◽  
O. Petrov
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Mechanical Characteristics ◽  
Physical And Mechanical Properties ◽  
Specific Pore Volume ◽  
Cement Mortars ◽  
Physical And Mechanical Characteristics

AbstractCement mortars and concretes incorporating clinoptilolite, silica fume and fly ash were investigated for changes in their physical and mechanical properties. It was found that additions of 10% clinoptilolite and 10% Pozzolite (1:1 mixture of silica fume and fly ash) were optimal for improvement of the quality of the hardened products, giving 8% and 13% increases in flexural and compressive strength respectively. The specific pore volume of the mortars incorporating zeolite decreased between the 28th and 180th day to levels below the values for the control composition due to the fact that clinoptilolite exhibits its pozzolanic activity later in the hydration. In these later stages, pores with radii below 500 nm increased at the expense of larger pores. The change in the pore-size distribution between the first and sixth months of hydration occurs mostly in the mortars with added zeolite.

scholarly journals Effect of fly ash on physical and mechanical properties of mortar

2019 ◽  
Vol 17 (6) ◽  
pp. 35
Author(s):  
Vu-An Tran
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Water Absorption ◽  
Thermal Power ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Flow Density ◽  
Control Specimen

This research investigates the physical and mechanical properties of mortar incorporating fly ash (FA), which is by-product of Duyen Hai thermal power plant. Six mixtures of mortar are produced with FA at level of 0%, 10%, 20%, 30%, 40%, and 50% (by volume) as cement replacement and at water-to-binder (W/B) of 0.5. The flow, density, compressive strength, flexural strength, and water absorption tests are made under relevant standard in this study. The results have shown that the higher FA content increases the flow of mortar but significantly decreases the density of mixtures. The water absorption and setting time increases as the samples incorporating FA. Compressive strength of specimen with 10% FA is approximately equal to control specimen at the 91-day age. The flexural strength of specimen ranges from 7.97 MPa to 8.94 MPa at the 91-day age with the best result for samples containing 10% and 20% FA.

scholarly journals Influence of curing age on high-temperature properties of additive manufactured geopolymer mortar

2020 ◽  
Vol 218 ◽  
pp. 03019
Author(s):  
Xiaohong Yin ◽  
Xiaodong Wang ◽  
Yuan Fang ◽  
Zhu Ding
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Flexural Strength ◽  
High Temperature Properties ◽  
Before And After ◽  
3D Printed ◽  
Curing Age

Some researches have been conducted on the application of geopolymer in 3D printing. However, there is no publication about the high-temperature properties of 3D printed geopolymer made from fly ash, slag, and metakaolin. This paper presents the experimental research on the mechanical properties of 3D printed geopolymer after being exposed to elevated empratures. The effects of curing age on high-temperature properties are analyzed. The heating temperasures were 300 °C, 600 °C, and 900 °C, and the holding time was one hour. After exposure to temperatures, the flexural strength of 3D printed geopolymer exhibited different change trends with increasing curing age for different exposure temperatures. Before and after exposure to elevated temperature, the 3D printed geopolymer experienced significant anisotropic compressive strengths. The change trends of compressive strength at different exposure temperatures wit hincreasing curing ages were different from each other on different loading directions.

Silicate Sprayed Mixture Based on Secondary Raw Materials

2019 ◽  
Vol 808 ◽  
pp. 129-135
Author(s):  
Petr Figala ◽  
Rostislav Drochytka ◽  
Radek Hermann ◽  
Jiří Kolísko
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Fly Ash ◽  
Raw Materials ◽  
Positive Influence ◽  
Foundry Sand ◽  
Secondary Raw Materials ◽  
Fundamental Research

This paper studies the fundamental research and development of sprayed cement-based mixture designed to withstand the chemically aggressive conditions. The aim of this paper is to verify the possibilities of usage of suitable secondary raw materials as a substitution of a binder and filler of the original mixture while preserving or improving the physical-mechanical properties. In this part of the research was studied the possibility to substitute the binder in rate of 20-60 wt.% by high temperature fly ash and the whole filler by foundry sand and slag. Test samples were made from nine recipes, in which was monitored the influence of secondary raw materials on the compressive strength and the water absorption after 28 days of curing. The results of this paper show, it is possible to successfully substitute part of the binder by high temperature fly ash and the filler wholly by foundry sand in the sprayed mixture. These optimized recipes showed positive influence mainly in the long-term on mechanical properties.

scholarly journals Peculiarities of hydration of Portland cement with synthetic nano-silica

2017 ◽  
Vol 12 (2) ◽  
pp. 101-106 ◽  
Author(s):  
Galyna Kotsay
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Portland Cement ◽  
Cement Hydration ◽  
Physical And Mechanical Properties ◽  
The Other ◽  
Nano Materials ◽  
Nano Silica ◽  
Other Hand ◽  
Materials Used

Abstract Application of nano-materials in cement products significantly, improves their properties. Of course, the effectiveness of the materials depends on their quantity and the way they are introduced into the system. So far, amongst nano-materials used in construction, the most preferred was nano-silica. This research investigated the effect of synthetic precipitated nano-silica on the cement hydration as well as, on the physical and mechanical properties of pastes and mortars. Obtained results showed that admixture of nano-silica enhanced flexural and compressive strength of cement after 2 and 28 days, however, only when admixture made up 0.5% and 1.0%. On the other hand, the use of nano-silica in the amount 2% had some limitations, due to its ability to agglomerate, which resulted in deterioration of the rheological and mechanical properties.

scholarly journals The mechanical properties of fly ash concrete prepared and cured at high temperatures

2017 ◽  
Vol 18 (2) ◽  
Author(s):  
D.R. Munaf ◽  
M.S. Besari ◽  
M.M. IqbaP ◽  
And I. Kadir
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Fly Ash ◽  
Exponential Function ◽  
Elevated Temperatures ◽  
Physical And Mechanical Properties ◽  
Strength Properties ◽  
Fly Ash Concrete ◽  
Simple Exponential Function ◽  
Strain Relationship

Results of an experimental investigation on the effect of fly ash content, water cement (w/c) ratio of concrete prepared and cured at temperatures of ambience, 40°C and 60°C are presented in this paper. The mechanical properties investigated here include its workability, its behaviour under compression and splitting tension. Microscopic investigations were also carried out using SEM micrographic images to gain understanding of concrete at its microstructural level.The results indicate that high temperature increases early compressive strengths of concrete, but has decreasing effects on the strengths at later ages. The use of fly ash in concretes cast and cured at elevated temperatures improves the physical and mechanical properties of fresh as well as those of hardened concrete.Various mathematical models describing the properties of such concretes are considered at the end of this paper. The strength properties of high temperature fly ash concrete were best represented by a simple exponential function of time, while its stress-strain relationship could be best described by an exponential function of strain of a more complicated form.

Effect of white soil substitution on fly ash based mortar geopolymers with sodium hydroxide activator

2020 ◽  
Vol 26 (1) ◽  
pp. 9-16
Author(s):  
Yulita Arni Priastiwi ◽  
Arif Hidayat ◽  
Dwi Daryanto ◽  
Zidny Salamsyah Badru
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Moisture Content ◽  
Sodium Hydroxide ◽  
Modulus Of Elasticity ◽  
Physical And Mechanical Properties ◽  
Test Results ◽  
Alkaline Activator ◽  
Made In

The presence of white soil in a geopolymer mortar affects the physical and mechanical properties of the mortar itself, especially in compressive strength, density and modulus of elasticity produced. Geopolymer mortar composed of fly ash, sand, water, and NaOH which acts as an alkaline activator compared to mortar from the same material, but white soil from Kupang is added as a substitution of fly ash. Specimens are made in six variations. Geopolymer mortar composers using a ratio of 1 binder: 3 sand with w/b of 0.5. Binder composed of fly ash with white soil substitution of 0; 5; 10; 15; 20 and 30% by weight of fly ash. An activator NaOH 8M solution was added to the mixture. Both white soil and fly ash pass of sieve no. 200 with a moisture content of 0%. Mortar made measuring 5x5x5 cm. The mortar was treated by the oven of method at 60 oC for 24 hours until the mortar does not change in weight. The test results show geopolymer mortar with 15% substitution of white soil to fly ash has the highest compressive strength, density and modulus of elasticity among other variations. In all mortar variations, compressive strength at 14 days has reached 75% of strength at 28 days.

scholarly journals KUAT TEKAN BETON CAMPURAN GGBFS DAN FLY ASH MENGGUNAKAN RETARDER

2021 ◽  
Vol 15 (1) ◽  
pp. 51
Author(s):  
Anni Susilowati ◽  
Iqbal Yusra
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Test Methods ◽  
Optimum Level ◽  
Statistical Regression ◽  
Level Of Use ◽  
Regression Test

Abstract One of the world's construction needs is casting in large volumes that require concrete with low hydration heat, and one of the problems is that the concrete has a setting during the casting queue. Therefore, a research was conducted on adding retarder to concrete with a mixture of GGBFS and Fly Ash. The purpose of this research was to analyze the physical and mechanical properties of concrete, the effect of adding retarder and obtain optimal retarder levels. This research used an experimental methods to make concrete specimens of 75% cement mix: GGBFS 15%: Fly Ash 10% with a water cement ratio of 0.5 using mix design SNI-03-2834-2000. Variations of the retarder added to the concrete mixture were 0%, 0.2%, 0.4%, and 0.6% by weight of cement with the Naptha RD 31 type. Analysis of the effect of the retarder used statistical regression test methods on SPSS. The results of research obtained the longest setting time in this researchwas 1890 minutes at a variation of 0.6% with a slump of 168 mm. The compressive strength of the concrete increased by 12.07% - 52.36% by using a retarder added material. Based on the research results, it was obtained that the optimum level of use of retarder in mixed concrete GGBFS and Fly Ash was 0.2% because it has the best physical and mechanical properties. Keywords: Fly Ash, GGBFS, Compressive Strength, Retarder

scholarly journals Study on the Physical and Mechanical Properties of Granite After Multiple Thermal Shock Treatments

2020 ◽  
Author(s):  
Li Yu ◽  
Hai-wang PENG ◽  
Yu Zhang ◽  
GuoWei Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
High Temperature ◽  
Thermal Shock ◽  
Tensile Modulus ◽  
Physical And Mechanical Properties ◽  
P Wave ◽  
Water Cooling ◽  
Thermal Shocks

Abstract To study the influence of thermal shock caused by water cooling on the physical and mechanical properties of high-temperature granite, granite was subjected to an increasing number of high-temperature (300℃) water-cooling and thermal shock treatment cycles, and static mechanical experiments were carried out on the treated granite. The results support the following conclusions: (1) Thermal shock causes an increase in the number and size of the pores and cracks within the granite; thus, its volume expands, density decreases, water absorption rate increases, and P-wave velocity decreases. (2) With an increase in the number of thermal shocks, both the compressive strength and tensile strength of the granite decrease, and there is a linear relationship between the compressive strength and tensile strength. With the corresponding fitting formula, the change in the strength of the granite can be accurately predicted. (3) With an increase in the number of thermal shocks, the plasticity of the granite increases and its resistance to deformation weakens, which is manifested as a decrease in both the compressive modulus and tensile modulus of the granite. After 15 cycles of thermal shock, the compressive elastic modulus and tensile modulus of the granite decreased by 25.18% and 46.76%, respectively. (4) The m and s values of the damaged granite were calculated based on the Hoek-Brown empirical criterion, and it was found that both of these parameters decrease with the increase in the number of thermal shocks. The calculation results can provide a reference for engineering rock mass failure.Clinical trial registration

Sign in / Sign up

Export Citation Format

Share Document