scholarly journals Optimization of aeration enhanced surfactant soil washing for remediation of diesel-contaminated soils using response surface methodology

PeerJ ◽  
2020 ◽  
Vol 8 ◽  
pp. e8578
Author(s):  
Befkadu Abayneh Ayele ◽  
Jun Lu ◽  
Quanyuan Chen
Keyword(s):  
Particle Size ◽  
Response Surface Methodology ◽  
Organic Matter ◽  
Response Surface ◽  
Removal Efficiency ◽  
Contaminated Soils ◽  
Organic Matter Content ◽  
Soil Washing ◽  
Agitation Speed ◽  
Airflow Rate

Surfactant-enhanced soil washing has been used for remediation of organic pollutants for an extended period, but its effectiveness and wide application was limited by the high concentration of surfactants utilized. In this work, the efficiency of conventional soil washing performance was enhanced by 12–25% through the incorporation of air bubbles into the low concentration surfactant soil washing system. Surfactant selection pre-experiment using aerated and conventional soil washing reveals Brij 35 > TX100 > Tween 80 > Saponin in diesel oil removal. Optimization of the effect of time, surfactant concentration, pH, agitation speed, and airflow rate in five levels were undertaken using Response Surface Methodology and Central composite design. The optimum degree of variables achieved was 90 min of washing time, 370 mg/l of concentration, washing pH of 10,535 rpm of agitation speed and 7.2 l/min of airflow rate with 79.5% diesel removal. The high predicted R2 value of 0.9517 showed that the model could efficiently be used to predict diesel removal efficiency. The variation in efficiency of aeration assisted and conventional soil washing was variable depending on the type of surfactant, organic matter content of the soil, particle size distribution and level of pollutant weathering. The difference in removal efficiency of the two methods increases when the level of organic matter increases and when the particle size and age of contamination decreases.

scholarly journals Response surface methodology approach for the optimisation of adsorption of hydrolysed polyacrylamide from polymer-flooding wastewater onto steel slag: a good option of waste mitigation

2017 ◽  
Vol 76 (4) ◽  
pp. 776-784 ◽  
Author(s):  
Mijia Zhu ◽  
Jun Yao ◽  
Zhonghai Qin ◽  
Luning Lian ◽  
Chi Zhang
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Removal Efficiency ◽  
Contact Time ◽  
Interactive Effect ◽  
Steel Slag ◽  
Oxygen Demand ◽  
Polymer Flooding ◽  
High Concentration ◽  
Adsorbent Dosage

Wastewater produced from polymer flooding in oil production features high viscosity and chemical oxygen demand because of the residue of high-concentration polymer hydrolysed polyacrylamide (HPAM). In this study, steel slag, a waste from steel manufacturing, was studied as a low-cost adsorbent for HPAM in wastewater. Optimisation of HPAM adsorption by steel slag was performed with a central composite design under response surface methodology (RSM). Results showed that the maximum removal efficiency of 89.31% was obtained at an adsorbent dosage of 105.2 g/L, contact time of 95.4 min and pH of 5.6. These data were strongly correlated with the experimental values of the RSM model. Single and interactive effect analysis showed that HPAM removal efficiency increased with increasing adsorbent dosage and contact time. Efficiency increased when pH was increased from 2.6 to 5.6 and subsequently decreased from 5.6 to 9.3. It was observed that removal efficiency significantly increased (from 0% to 86.1%) at the initial stage (from 0 min to 60 min) and increased gradually after 60 min with an adsorbent dosage of 105.2 g/L, pH of 5.6. The adsorption kinetics was well correlated with the pseudo-second-order equation. Removal of HPAM from the studied water samples indicated that steel slag can be utilised for the pre-treatment of polymer-flooding wastewater.

Electrocoagulation and nanofiltration integrated process application in purification of bilge water using response surface methodology

2016 ◽  
Vol 74 (3) ◽  
pp. 564-579 ◽  
Author(s):  
Ceyhun Akarsu ◽  
Yasin Ozay ◽  
Nadir Dizge ◽  
H. Elif Gulsen ◽  
Hasan Ates ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Removal Efficiency ◽  
Cod Removal ◽  
Positive Sign ◽  
Aluminum Electrode ◽  
Integrated Process ◽  
Bilge Water ◽  
Cod Removal Efficiency ◽  
Initial Ph

Marine pollution has been considered an increasing problem because of the increase in sea transportation day by day. Therefore, a large volume of bilge water which contains petroleum, oil and hydrocarbons in high concentrations is generated from all types of ships. In this study, treatment of bilge water by electrocoagulation/electroflotation and nanofiltration integrated process is investigated as a function of voltage, time, and initial pH with aluminum electrode as both anode and cathode. Moreover, a commercial NF270 flat-sheet membrane was also used for further purification. Box–Behnken design combined with response surface methodology was used to study the response pattern and determine the optimum conditions for maximum chemical oxygen demand (COD) removal and minimum metal ion contents of bilge water. Three independent variables, namely voltage (5–15 V), initial pH (4.5–8.0) and time (30–90 min) were transformed to coded values. The COD removal percent, UV absorbance at 254 nm, pH value (after treatment), and concentration of metal ions (Ti, As, Cu, Cr, Zn, Sr, Mo) were obtained as responses. Analysis of variance results showed that all the models were significant except for Zn (P > 0.05), because the calculated F values for these models were less than the critical F value for the considered probability (P = 0.05). The obtained R2 and Radj2 values signified the correlation between the experimental data and predicted responses: except for the model of Zn concentration after treatment, the high R2 values showed the goodness of fit of the model. While the increase in the applied voltage showed negative effects, the increases in time and pH showed a positive effect on COD removal efficiency; also the most effective linear term was found as time. A positive sign of the interactive coefficients of the voltage–time and pH–time systems indicated synergistic effect on COD removal efficiency, whereas interaction between voltage and pH showed an antagonistic effect.

Sign in / Sign up

Export Citation Format

Share Document