scholarly journals Biosorption potential of natural, pyrolysed and acid-assisted pyrolysed sugarcane bagasse for the removal of lead from contaminated water

PeerJ ◽  
2018 ◽  
Vol 6 ◽  
pp. e5672 ◽  
Author(s):  
Ghulam Mustafa Shah ◽  
Muhammad Nasir ◽  
Muhammad Imran ◽  
Hafiz Faiq Bakhat ◽  
Faiz Rabbani ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Sugarcane Bagasse ◽  
Contact Time ◽  
Industrial Effluents ◽  
Isotherm Models ◽  
Contaminated Water ◽  
Concentration Maximum ◽  
Freundlich Adsorption Isotherm ◽  
Pb Ions ◽  
Pb Concentration

Lead (Pb) is a ubiquitous pollutant which poses serious threats to plants, animals and humans once entered into the food chain via contaminated industrial effluents on their discharge into the surface of water bodies and/or geological materials. This study aimed to examine and compare the biosorption potential of natural sugarcane bagasse (NB), pyrolysed sugarcane bagasse (PB) and acid assisted pyrolysed sugarcane bagasse (APB) for the removal of Pb from contaminated water. To explore this objective, a series of batch experiments were conducted at various adsorbent mass (0.25, 0.5, 0.75, 1.0 g per 100 ml contaminated water), initial Pb concentration (7, 15, 30, 60 and 120 ppm), and contact time (7, 15, 30, 60 and 120 min). Results revealed that all the tested bio-sorbents have potential to adsorb and remove Pb ions from the contaminated water. In this regard, APB proved more effective since it removed 98% of Pb from aqueous solution at initial Pb concentration of 7 ppm and mass of 0.25 g per 100 ml of aqueous solution. The respective values in case of NB and PB were 90 and 95%. For a given adsorbent type, Pb adsorption decreased by increasing the mass from 0.25 to 1.0 g per 100 ml of aqueous solution. However, the greatest Pb removal occurred at adsorbent mass of 1.0 g per 100 ml of aqueous solution. Initial Pb concentration had a great impact on Pb adsorption and removal by adsorbent. The former increased and the latter decreased with the increase in initial Pb concentration from seven to 120 ppm. At seven ppm Pb concentration, maximum Pb removal took place irrespective to the adsorbent type. Out of the total Pb adsorption and removal, maximum contribution occurred within 15 min of contact time between the adsorbate and adsorbent, which slightly increased till 30 min, thereafter, it reached to equilibrium. Application of equilibrium isotherm models revealed that our results were better fitted with Freundlich adsorption isotherm model. Overall, and for the reasons detailed above, it is concluded that sugarcane bagasse has capabilities to adsorb and remove Pb ions from contaminated water. Its bio-sorption potential was considerably increased after pyrolysis and acid treatment.

Adsorption of Cadmium from Aqueous Solution by Biomass: Comparison of Solid Pineapple Waste, Sugarcane Bagasse and Activated Carbon

2013 ◽  
Vol 832 ◽  
pp. 810-815 ◽  
Author(s):  
M.S. Rosmi ◽  
S. Azhari ◽  
R. Ahmad
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Sugarcane Bagasse ◽  
Contact Time ◽  
Agricultural Waste ◽  
Palm Kernel ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Adsorbent Dosage ◽  
Pineapple Waste

The use of low-cost adsorbent derived from agricultural waste has been investigated for the removal of Cd (II) from aqueous solution. This research reports the feasibility of using solid pineapple waste (SPW), sugarcane bagasse (SCB) and activated carbon (AC) derived from palm kernel for the removal of Cd (II) under different experimental conditions. Batch experiments were carried out at various pH (3-12), adsorbent dosage (0.01-2 g) and contact time (15-150 min). The maximum Cd (II) removal was shown by SPW (90%) followed by SCB (55%) and AC (30%) at pH 7 with a contact time of 120 min, adsorbent dosage of 1.0 g and at 1.0 ppm of the initial concentration of Cd (II) solution. The kinetics study shows that the adsorption process fitted the pseudo-second-order-model. The experimental data was analysed by both Freundlich and Langmuir isotherm models. It was found that the Langmuir model appears to well fit the isotherm. The Langmuir maximum adsorption capacity calculated from Langmuir for SPW, SBC and AC were 0.3332 mg/g, 0.1865 mg/g and 0.1576 mg/g respectively. The order of Cd (II) removal by the adsorbents was SPW>SCB>AC. Thus, SPW may be an alternative adsorbent for the removal of Cd (II) ions form aqueous solution. The characterization of the SPW, SCB and AC were also carried out by using Scanning Electron Microscopy (SEM) and Nitrogen Gas Adsorption Single Point Surface Area Analyzer (BET).

scholarly journals Modified/Unmodified Nanoparticle Adsorbents of Cellulose Origin With High Adsorptive Potential for Removal of Pb(II) From Aqueous Solution

2017 ◽  
Vol 13 (27) ◽  
pp. 425
Author(s):  
Azeh Yakubu ◽  
Gabriel Ademola Olatunji ◽  
Folahan Amoo Adekola
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Correlation Coefficients ◽  
Solution Temperature ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Kinetics Of Adsorption ◽  
Kinetics Of

This investigation was conducted to evaluate the adsorption capacity of nanoparticles of cellulose origin. Nanoparticles were synthesized by acid hydrolysis of microcrystalline cellulose/cellulose acetate using 64% H3PO4 and characterized using FTIR, XRD, TGA-DTGA, BET and SEM analysis. Adsorption kinetics of Pb (II) ions in aqueous solution was investigated and the effect of initial concentration, pH, time, adsorbent dosage and solution temperature. The results showed that adsorption increased with increasing concentration with removal efficiencies of 60% and 92.99% for Azeh2 and Azeh10 respectively for initial lead concentration of 3 mg/g. The effects of contact time showed that adsorption maximum was attained within 24h of contact time. The maximum adsorption capacity and removal efficiency were achieved at pH6. Small dose of adsorbent had better performance. The kinetics of adsorption was best described by the pseudo-second-Order model while the adsorption mechanism was chemisorption and pore diffusion based on intra-particle diffusion model. The isotherm model was Freundlich. Though, all tested isotherm models relatively showed good correlation coefficients ranging from 0.969-1.000. The adsorption process was exothermic for Azeh-TDI, with a negative value of -12.812 X 103 KJ/mol. This indicates that the adsorption process for Pb by Azeh-TDI was spontaneous. Adsorption by Azeh2 was endothermic in nature.

ADSORPTION OF ACID ORANGE 7 BY CETYLPYRIDINIUM BROMIDE MODIFIED SUGARCANE BAGASSE

2016 ◽  
Vol 78 (1-2) ◽  
Author(s):  
Nik Ahmad Nizam Nik Malek ◽  
Nurain Mat Sihat ◽  
Mahmud A. S. Khalifa ◽  
Auni Afiqah Kamaru ◽  
Nor Suriani Sani
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Sugarcane Bagasse ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Acid Orange 7 ◽  
Cetylpyridinium Bromide ◽  
Batch Mode ◽  
Acid Orange ◽  
Adsorption Data

In the present study, the adsorption of acid orange 7 (AO7) dye from aqueous solution by sugarcane bagasse (SB) and cetylpyridinium bromide (CPBr) modified sugarcane bagasse (SBC) was examined. SBC was prepared by reacting SB with different concentrations (0.1, 1.0 and 4.0 mM) of cationic surfactant, CPBr. The SB and SBC were characterized using Fourier transform infrared (FTIR) spectroscopy. The adsorption experiments were carried out in a batch mode. The effect of initial AO7 concentrations (5-1000 mg/L), initial CPBr concentrations and pH of AO7 solution (2-9) on the adsorption capacity of SB and SBC were investigated. The experimental adsorption data were analyzed using Langmuir and Freundlich isotherm models. The adsorption of AO7 onto SB and SBC followed Freundlich and Langmuir isotherm models, respectively. The maximum uptake of AO7 was obtained by SBC4.0 (SB treated with 4.0 mMCPBr) with the adsorption capacity of 144.928 mg/g. The highest AO7 removal was found to be at pH 2 and 7 for SB and SBC, respectively. As a conclusion, sugarcane bagasse modified with CPBr can become an alternative adsorbent for the removal of anionic compounds in aqueous solution.

scholarly journals Equilibrium, Kinetics, and Thermodynamics of the Removal of Nickel(II) from Aqueous Solution Using Cow Hooves

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
I. Osasona ◽  
O. O. Ajayi ◽  
A. O. Adebayo
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Room Temperature ◽  
Physical Adsorption ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Equilibrium Studies ◽  
Equilibrium Data

The feasibility of using powdered cow hooves (CH) for removing Ni2+ from aqueous solution was investigated through batch studies. The study was conducted to determine the effect of pH, adsorbent dosage, contact time, adsorbent particle size, and temperature on the adsorption capacity of CH. Equilibrium studies were conducted using initial concentration of Ni2+ ranging from 15 to 100 mgL−1 at 208, 308, and 318 K, respectively. The results of our investigation at room temperature indicated that maximum adsorption of Ni2+ occurred at pH 7 and contact time of 20 minutes. The thermodynamics of the adsorption of Ni2+ onto CH showed that the process was spontaneous and endothermic. Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models were used to quantitatively analysed the equilibrium data. The equilibrium data were best fitted by Freundlich isotherm model, while the adsorption kinetics was well described by pseudo-second-order kinetic equation. The mean adsorption energy obtained from the D-R isotherm revealed that the adsorption process was dominated by physical adsorption. Powdered cow hooves could be utilized as a low-cost adsorbent at room temperature under the conditions of pH 7 and a contact time of 20 minutes for the removal of Ni(II) from aqueous solution.

Sorption of Copper and Zinc from Aqueous Solutions by Microwave Incinerated Sugarcane Bagasse Ash (MISCBA)

2016 ◽  
Vol 835 ◽  
pp. 378-385 ◽  
Author(s):  
Ibrahim Umar Salihi ◽  
Shamsul Rahman Mohamed Kutty ◽  
Mohamed Hasnain Isa ◽  
Usman Aminu Umar ◽  
Emmanuel Olisa
Keyword(s):  
Heavy Metals ◽  
Aqueous Solution ◽  
Correlation Coefficient ◽  
Sugarcane Bagasse ◽  
Contact Time ◽  
Industrial Wastewater ◽  
Low Cost ◽  
Isotherm Model ◽  
Copper And Zinc ◽  
Sugarcane Bagasse Ash

Industrial wastewater containing toxic pollutants such as heavy metals tends to contaminate the environment once it is release without proper treatment. Heavy metals are toxic to both human and other living organisms. It is necessary to treat industrial wastewater polluted with heavy metals prior to its discharge into the receiving environment. In this study, low cost adsorbent was generated from sugarcane bagasse through incineration. The prepared adsorbent “microwave incinerated sugarcane bagasse ash” (MISCBA) was used in removing copper and zinc from aqueous solution. Parameters of importance such as pH, contact time and adsorbent dosages are studied to investigate their effects on the adsorption of copper and zinc. Maximum adsorption was observed at pH 6.0, contact time of 180 minutes and adsorbent dosage of 10 g/L. Zinc removal follows Langmuir isotherm model with correlation coefficient of 0.9291. Copper adsorption follows both Langmuir and Freundlich isotherm model with correlation coefficient of 0.9181 and 0.9742, respectively. Removal capacities of 38.4 mg/g and 20.4 mg/g were obtained for copper and zinc, respectively. Application of MISCBA as low - cost adsorbent have shown significant outcome in removal of copper and zinc from aqueous solution.

scholarly journals Biosorption of Cr(III) from aqueous solution using an agricultural by-product jute stick powder: Equilibrium and kinetic studies

2018 ◽  
Vol 9 (3) ◽  
pp. 202-212 ◽  
Author(s):  
Mohammad Nasir Uddin ◽  
Jahangir Alam ◽  
Syeda Rahimon Naher
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Metal Ion ◽  
Water Solution ◽  
Low Cost ◽  
Isotherm Models ◽  
Infrared Spectrometry ◽  
Order Kinetic ◽  
Adsorption Model ◽  
Experimental Conditions

The adsorption capacity of chromium(III) from synthetic waste water solution by a low cost biomaterial, Jute Stick Powder (JSP)was examined. A series of batch experiments were conducted at different pH values, adsorbent dosage and initial chromium concentration to investigate the effects of these experimental conditions. To analyze the metal adsorption on to the JSP, most common adsorption isotherm models were applied. To study the reaction rate, the kinetic and diffusion models were also applied. The morphological structure and variation of functional groups in the JSP before and after adsorption was examined by scanning electron microscope (SEM) and Fourier transform infrared spectrometry (FT-IR). Maximum chromium removal capacities of JSP was 84.34%with corresponding equilibrium uptake 8.4 mg/g from 50 mg/L of synthetic metal solution in 60 minutes of contact time at pH = 6.0 and 28 °C with continuous stirring at 180 rpm. The percent sorption of the biomass decreased with increasing concentration of metal ion but increased with decreasing pH, increasing contact time and adsorbent doses. Data for this study indicated a good correspondence with both isotherms of Langmuir and Freundlich isotherm. The analysis of kinetic indicated that Chromium was consistent with the second-order kinetic adsorption model. The rate of removal of Cr(III) ions from aqueous solution by JSP was found rapid initially within 5-30 minutes and reached in equilibrium in about 40 minutes. The investigation revealed that JSP, a low cost agricultural byproduct, was a potential adsorbent for removal of heavy metal ions from aqueous solution.

scholarly journals Chemical and physical preparation of activated carbon using Raw bagasse for cationic dye adsorption

2016 ◽  
Vol 18 (2) ◽  
pp. 402-415 ◽  
Keyword(s):  
Activated Carbon ◽  
Sugarcane Bagasse ◽  
Contact Time ◽  
Dye Adsorption ◽  
Isotherm Models ◽  
Adsorptive Capacity ◽  
Adsorption Isotherm Models ◽  
Equilibrium Data ◽  
Agriculture Wastes ◽  
Physical Preparation

<div> <p>Agriculture wastes like sugarcane bagasse are available in large quantities in Egypt. Various adsorbents from natural materials, industrial waste materials, agricultural by-products, and biomass based activated carbon can be used in the removal of various dyes. Raw Bagasse pith (RBP) was used to prepare activated carbon (AC) using phosphoric acid (H<sub>3</sub>PO<sub>4</sub>) as a chemical activating agent. C The raw BP and the synthesized adsorbent were characterized by Fourier transform infrared (FTIR) spectroscopy and scanning electron microscope (SEM). The effectiveness of AC prepared in adsorption of methylene blue (MB) has been studied as a function of adsorbent type, initial dye concentration and contact time. The effects of the initial dye concentration and contact time were evaluated. Adsorption isotherm models - Langmuir, Freundlich and Temkin were used to simulate the equilibrium data. Langmuir equation was found to have the highest value of R<sup>2</sup> compared with other models. Furthermore, it was found that sugarcane bagasse have a high adsorptive capacity towards MB.</p> </div> <p>&nbsp;</p>

scholarly journals Thermodynamic Study on the Adsorption of Pb2+and Zn2+From Aqueous Solution by Human Hair

2010 ◽  
Vol 7 (4) ◽  
pp. 1296-1303 ◽  
Author(s):  
A. S. Ekop ◽  
N. O. Eddy
Keyword(s):  
Aqueous Solution ◽  
Human Hair ◽  
Contact Time ◽  
Metal Ion ◽  
Ion Concentration ◽  
Optimum Conditions ◽  
Batch System ◽  
Freundlich Adsorption Isotherm ◽  
Equilibrium Data ◽  
Adsorption Equilibrium Data

Adsorption of Pb(II) and Zn(II) ions from aqueous solutions was studied in a batch system using modified human hair. The optimum conditions for the adsorption of Pb(II) and Zn(II) ions from aqueous solution by human hair were investigated by considering the extent of adsorption with respect to contact time, initial metal ion concentration and temperature. The results obtained indicates that the extent of metal ions removed decreases with increasing contact time but increased with increase in the initial metal ion concentration. The adsorption equilibrium data best fitted Freundlich adsorption isotherm. The adsorption of Pb(II) and Zn(II) ions onto human hair is endothermic, spontaneous and is characterised by increasing degree of orderliness.

scholarly journals Utilization of Banana (Musa sapientum) Peel for Removal of Pb2+ from Aqueous Solution

2021 ◽  
Vol 1 (2) ◽  
pp. 117-128
Author(s):  
Afrida Nurain ◽  
Protima Sarker ◽  
Md. Shiblur Rahaman ◽  
Md. Mostafizur Rahman ◽  
Md. Khabir Uddin
Keyword(s):  
Aqueous Solution ◽  
Heavy Metal ◽  
Adsorption Isotherm ◽  
Contact Time ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Agitation Speed ◽  
Banana Peel ◽  
Management Problem ◽  
Freundlich Adsorption Isotherm

Biosorption is a convenient process for heavy metal remediation. In this study, banana peel was experimented to eliminate lead (Pb2+) from an aqueous solution following batch experiments. The functional groups of banana peel were identified by Fourier-transform infrared spectroscopy (FTIR). The adsorption mechanism was studied by the Langmuir and Freundlich adsorption isotherm model and determined the separation factor from the Langmuir adsorption isotherm. The adsorption of Pb2+ on dried banana peel had been studied at different adsorbent doses, pH, initial concentration of Pb, contact time, temperature, and agitation speed. After adsorption, Pb2+ was measured using atomic absorption spectroscopy (AAS). Maximum adsorption had taken place at pH 5 for adsorbent dose 45 g L-1. The optimum contact time and agitation speed was 30 minutes and 150 rpm, respectively for the initial Pb concentration of 100 ppm at 25°C. Both, Langmuir and Freundlich adsorption isotherm models shows the best fitting (r2 = 0.9978 and 0.9595) for Pb2+ adsorption. The maximum Pb2+ adsorption capacity was 2.1 mg g-1. The findings indicate that the banana peel waste could be a potential adsorbent for heavy metal removal. Moreover, the waste management problem could be solved in an eco-friendly manner by utilizing it for the eradication of Pb2+ from wastewater.

scholarly journals Alternative Composite Nanosorbents Based on Turkish Perlite for the Removal of Cr(VI) from Aqueous Solution

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Serpil Edebali
Keyword(s):  
Electron Microscopy ◽  
Experimental Data ◽  
Aqueous Solution ◽  
Scanning Electron Microscopy ◽  
Contact Time ◽  
Isotherm Model ◽  
Isotherm Models ◽  
Chromium Removal ◽  
Ph Dependent ◽  
Scanning Electron

New nanocomposite sorbents were synthesized and used for Cr(VI) removal from aqueous solution by modifying Turkish perlite withα-MnO2(PAM) andγ-Fe2O3(PGI) nanoparticles. Nanocomposite sorbents were characterized using scanning electron microscopy (SEM) and FTIR. The effects of several parameters such as contact time, amount of sorbent, pH, and concentration were investigated and it was found that the sorption capacity for Cr(VI) was found to be highly pH dependent. Also the experimental data were evaluated in terms of different isotherm models. The data of PGI were well fit to DR isotherm model whereas PAM data were well described with Temkin isotherm model. The sorption capacities were found to be 8.64 and 7.6 mg g−1for PGI and PAM, respectively. This confirms that these nanocomposites retain the constituent nanoparticle properties while being macroscopic particles suitable for chromium removal in water treatment.

Sign in / Sign up

Export Citation Format

Share Document