scholarly journals HIGH CYCLE FATIGUE PROPERTIES OF AS-BUILT TI6AL4V (ELI) PRODUCED BY DIRECT METAL LASER SINTERING

2017 ◽  
Vol 28 (3) ◽  
Author(s):  
Lerata Botsane Malefane ◽  
W du Preez ◽  
M Maringa
Keyword(s):  
High Cycle Fatigue ◽  
Laser Sintering ◽  
Fatigue Properties ◽  
Cycle Fatigue ◽  
Direct Metal Laser Sintering

High Cycle Fatigue Life of Ti6Al4V Alloy Produced by Direct Metal Laser Sintering

2016 ◽  
Vol 258 ◽  
pp. 522-525 ◽  
Author(s):  
Radomila Konečná ◽  
Gianni Nicoletto ◽  
Adrián Bača ◽  
Ludvík Kunz
Keyword(s):  
Fatigue Life ◽  
High Cycle Fatigue ◽  
Fatigue Testing ◽  
Fatigue Behavior ◽  
Fatigue Crack Initiation ◽  
Laser Sintering ◽  
Ti6al4v Alloy ◽  
Cycle Fatigue ◽  
Direct Metal Laser Sintering ◽  
Stress Relieving

High cycle fatigue life of Ti6Al4V alloy specimens manufactured by Direct Metal Laser Sintering (DMLS) was experimentally determined. The DMLS fabrication process was characterized by a 400 W laser power and 50 μm layer melted thickness. Post-fabrication heat treatment consisted in stress relieving for 3 h at 720 °C in vacuum with subsequent cooling in argon atmosphere. Fatigue testing of specimens oriented in three different directions with respect to the material build direction was performed with the aim to examine the influence of the layered microstructure on the fatigue behavior. Results of measurement of surface roughness, metallographic examinations of the layered material and fractographic investigation of the fatigue fracture surfaces were employed in the discussion of fatigue crack initiation in DMLS fabricated Ti6Al4V alloy.

Experimental Study of Direct Metal Laser Sintering: High Cycle Fatigue Life and Process Parameters

2020 ◽  
Author(s):  
Riley Seyffert ◽  
Sudhir Kaul
Keyword(s):  
Fatigue Life ◽  
Layer Thickness ◽  
Process Parameters ◽  
High Cycle Fatigue ◽  
Laser Sintering ◽  
Bending Test ◽  
Cycle Fatigue ◽  
Direct Metal Laser Sintering ◽  
Build Time ◽  
Scan Speed

Abstract Direct Metal Laser Sintering (DMLS) is a relatively new manufacturing process in additive manufacturing (AM) that fuses powdered metal by using a high-powered laser. Although this process allows manufacturing prototypes without requiring specific tooling, it is challenging to use this process for manufacturing high volume production parts since complex shapes can take a significant amount of build time. Furthermore, manufactured parts also need some amount of post-processing to remove the support material that may be required due to the layer-by-layer build process. This study investigates three process parameters that could be optimized to substantially reduce production time. These three parameters are as follows: build layer thickness, laser scan speed, and laser hatch distance. In order to evaluate the influence of these parameters, manufactured parts made of AISI 316L Stainless Steel are tested for fatigue life and static strength. A three-point bending test is used as per ASTM E466. While none of the three parameters is seen to significantly influence ultimate tensile strength, results indicate that build layer thickness is a significant process parameter that directly affects fatigue life. Furthermore, the interaction between build layer thickness and laser scan speed is found to be statistically significant for high cycle fatigue. However, laser scan speed and laser hatch distance are seen to be statistically insignificant for fatigue life. The initial results of this study indicate that process parameters of DMLS need to be selected judiciously in order to minimize build time while maintaining structural integrity.

scholarly journals Usability of Ultrasonic Frequency Testing for Rapid Generation of High and Very High Cycle Fatigue Data

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2245
Author(s):  
Michael Fitzka ◽  
Bernd M. Schönbauer ◽  
Robert K. Rhein ◽  
Niloofar Sanaei ◽  
Shahab Zekriardehani ◽  
...  
Keyword(s):  
Strain Rate ◽  
High Cycle Fatigue ◽  
Fatigue Properties ◽  
Ultrasonic Frequency ◽  
Cycle Fatigue ◽  
Reinforced Polymer ◽  
Very High Cycle Fatigue ◽  
Ultrasonic Fatigue ◽  
Fibre Reinforced Polymer ◽  
Very High

Ultrasonic fatigue testing is an increasingly used method to study the high cycle fatigue (HCF) and very high cycle fatigue (VHCF) properties of materials. Specimens are cycled at an ultrasonic frequency, which leads to a drastic reduction of testing times. This work focused on summarising the current understanding, based on literature data and original work, whether and how fatigue properties measured with ultrasonic and conventional equipment are comparable. Aluminium alloys are not strain-rate sensitive. A weaker influence of air humidity at ultrasonic frequencies may lead to prolonged lifetimes in some alloys, and tests in high humidity or distilled water can better approximate environmental conditions at low frequencies. High-strength steels are insensitive to the cycling frequency. Strain rate sensitivity of ferrite causes prolonged lifetimes in those steels that show crack initiation in the ferritic phase. Austenitic stainless steels are less prone to frequency effects. Fatigue properties of titanium alloys and nickel alloys are insensitive to testing frequency. Limited data for magnesium alloys and graphite suggest no frequency influence. Ultrasonic fatigue tests of a glass fibre-reinforced polymer delivered comparable lifetimes to servo-hydraulic tests, suggesting that high-frequency testing is, in principle, applicable to fibre-reinforced polymer composites. The use of equipment with closed-loop control of vibration amplitude and resonance frequency is strongly advised since this guarantees high accuracy and reproducibility of ultrasonic tests. Pulsed loading and appropriate cooling serve to avoid specimen heating.

Sign in / Sign up

Export Citation Format

Share Document