Determination of the Optimum Lime Content for Asphalt Concrete Using Marshall Mix Design

2016 ◽  
Vol 5 (1) ◽  
pp. 9-14
Author(s):  
Olumide Moses Ogundipe ◽  
Sukanmi Sukanmi
Keyword(s):  
Asphalt Concrete ◽  
Mix Design ◽  
Lime Content

Initial Approach to Performance (Balanced) Mix Design: The Virginia Experience

2019 ◽  
Vol 2673 (2) ◽  
pp. 335-345 ◽  
Author(s):  
Stacey D. Diefenderfer ◽  
Benjamin F. Bowers
Keyword(s):  
Performance Testing ◽  
Performance Criteria ◽  
Mix Design ◽  
Department Of Transportation ◽  
Innovative Methods ◽  
Asphalt Mix ◽  
Performance Additives ◽  
Virginia Department ◽  
Selection Of

Performance mix design (PMD) of asphalt mixtures, often referred to as balanced mix design, is a design methodology that incorporates performance testing into the mix design process. The Virginia Department of Transportation (DOT), like many owner agencies, is interested in ways to specify asphalt mix designs better in an effort to make its roadway network more sustainable, longer lasting, and more economical. By adding performance criteria through a PMD framework, that goal can be achieved. Further, a PMD framework should allow for the development of new, innovative methods to increase pavement recyclability, new performance additives, and other means to enhance pavement performance. This paper provides details and documentation of the approach being taken by the Virginia DOT in their efforts to develop a PMD specification. Aspects of development presented include PMD method options, selection of performance tests, and determination of acceptance criteria. A discussion about validating specifications with in-service performance data and addressing quality control and quality assurance is also provided. Although additional work is needed for full development and implementation, the methodology being applied has been found to provide useful outcomes for the Virginia DOT even in the initial stages of development.

scholarly journals Determination of Construction Parameters of Porous Ultra-Thin Overlays Based on Laboratory Compaction Studies

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4496
Author(s):  
Jiahao Tian ◽  
Sang Luo ◽  
Ziming Liu ◽  
Xu Yang ◽  
Qing Lu
Keyword(s):  
Asphalt Concrete ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Combination Method ◽  
Compaction Temperature ◽  
Pavement Maintenance ◽  
Energy Equivalence ◽  
New Type ◽  
Better Than

To address the severe distresses of asphalt pavement, a new type of pavement maintenance treatment, porous ultra-thin overlay (PUTO) with small particle size was proposed. The PUTO has a thickness of 1.5–2.5 cm and a large void ratio of 18–25%. As a newly asphalt mixture, the structure characteristics differ from poor traditional pavement. Therefore, it is necessary to investigate the fabrication schemes in laboratory and on-site, respectively. In this study, the optimal fabrication schemes, including compaction temperature and number of blows of PUTO were determined based on Cantabro test and volumetric parameters. Then, the corresponding relationship between laboratory and on-site compaction work was then established based on the energy equivalent principle. On this basis, the numbers of on-site rolling passes and the combination method were calculated. The results show that increased compaction temperature and number of blows reduce the height and enhance the compaction of the Marshall sample. With the same temperature and number of blows, the raveling resistance of coarse gradation, Pavement Asphalt Concrete-1 (PAC-1) is better than that of fine gradation, Pavement Asphalt Concrete-2 (PAC-2), and the increased asphalt viscosity significantly improves the raveling resistance of the asphalt mixture. To ensure the scattering resistance and volumetric characteristic, the initial compaction temperature of the PAC-1 and PAC-2 should not be lower than 150 °C and 165 °C, respectively. Then, the laboratory compaction work and on-site compaction work were calculated and converted based on the principle of energy equivalence. Consequently, the on-site compaction combination of rolling machines for four asphalt mixtures was determined. According to the volumetric parameters, the paving test section proved that the construction temperature and the on-site rolling combination determined by laboratory tests are reasonable, and ultra-thin overlay has good structural stability, drainage, and skid resistance.

scholarly journals Effect of Hydrated Lime on Indirect Tensile Stiffness Modulus of Asphalt Concrete Produced in Half-Warm Mix Technology

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4731
Author(s):  
Mateusz M. Iwański
Keyword(s):  
Asphalt Concrete ◽  
Permanent Deformation ◽  
Active Agent ◽  
Hydrated Lime ◽  
Partial Replacement ◽  
Stiffness Modulus ◽  
Limestone Filler ◽  
Tensile Stiffness ◽  
Lime Content ◽  
Indirect Tensile

Half-warm mix asphalt (HWMA) mixtures can be produced at temperatures ranging from 100 °C to 130 °C, depending on the production methods used. The lowest mixing temperature can be achieved by using water-foamed bitumen. The mixture should be characterized by a long service life, defined by the resistance to permanent deformation and high stiffness modulus at temperatures above zero. It is therefore important to ensure the adequately high quality of the bitumen binder. Bitumen 50/70 was provided with appropriate quality foaming characteristics (expansion ratio, ER, half-life, t1/2) by adding a surface-active agent (SAA) at 0.6 wt % before foaming. Then asphalt concrete (AC) 8 S was designed and produced with the recommended water-foamed binder. Hydrated lime, an additive substantially affecting asphalt concrete mechanical parameters, was used at 0, 15, 30, and 45 wt % as a partial replacement for the limestone filler. The influence of the amount of hydrated lime on the content of voids, indirect tensile stiffness modulus at −10 °C, 0 °C, +10 °C, +20 °C, and +30 °C, and the resistance to permanent deformation was investigated. Statistical analysis of the test results showed the quantity of 30% to be the optimum hydrated lime content. The AC 8 S resistance to permanent deformation was determined at the optimum hydrated lime content. The comprehensive evaluation revealed a synergistic effect between bitumen 50/70, modified before foaming with 0.6 wt % SAA and 30 wt % hydrated lime as the limestone filler replacement, and the half warm mixture AC 8 S, in terms of the standard requirements and durability of the HWMA concrete in pavement applications.

Sign in / Sign up

Export Citation Format

Share Document