Dual-fuel Operation of Compression-ignition Engine Using Biodiesel for Pilot Injection

2012 ◽  
Author(s):  
Kelvin D. H. Bob-Manuel ◽  
Roy J. Crookes ◽  
Theodosios Korakianitis ◽  
Ashand M. Namasivayam
Keyword(s):  
Natural Gas ◽  
Environmental Protection Agency ◽  
Power Plants ◽  
Gas Flow ◽  
Stable Condition ◽  
Pressure Rise ◽  
Pilot Injection ◽  
Compression Ignition ◽  
Maritime Industry ◽  
Compression Ignition Engine

Economic factor and stringent emission standards are imposing constraints on current and future operation of power plants in the maritime industry. Hence, research institutions have intensified investigation on technologies for emission control and economy using alternative and sustainable/renewable fuels to achieve friendly environment. In this study, the combustion characteristics of natural gas and hydrogen fuelled compression ignition engine operated under stable condition using either neat or emulsified rapeseed methyl ester (RME) for pilot ignition were investigated. Ignition delay and rate of cylinder pressure rise at 1000 and 1500 r/min were obtained at various gas flow rates while the emission of NOx, CO2 and HC were measured. NOx concentrations were compared with the regulated IMO MARPOL73/78 and United States Environmental Protection Agency (EPA) Tier 3 standards and were observed to be lower than the MARPOL 73/78 level at both speeds and the EPA standard at 1500 r/min for the minimum specification of category 1 engines. Emulsified RME fuel pilot injection reduced NOx emission at all test conditions using natural gas. The use of hydrogen subscribed mainly in the reduction of particulate matters (PM) and CO2 and hence will contribute in the reduction of greenhouse effect (climate change) on the environment.

Operation of a Compression Ignition Engine with a HEUI Injection System on Natural Gas with Diesel Pilot Injection

1999 ◽  
Author(s):  
Talus Park ◽  
Richard J. Atkinson ◽  
Nigel Clark ◽  
Michael L. Traver ◽  
Christopher M. Atkinson
Keyword(s):  
Natural Gas ◽  
Injection System ◽  
Pilot Injection ◽  
Compression Ignition ◽  
Compression Ignition Engine

Experimental Investigation of a Heavy-Duty Compression-Ignition Engine Retrofitted to Natural Gas Spark-Ignition Operation

2019 ◽  
Vol 141 (11) ◽  
Author(s):  
Jinlong Liu ◽  
Hemanth Kumar Bommisetty ◽  
Cosmin Emil Dumitrescu
Keyword(s):  
Natural Gas ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Compression Ignition ◽  
Heavy Duty ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Cycle Variation ◽  
Spark Timing ◽  
Ci Engines

Heavy-duty compression-ignition (CI) engines converted to natural gas (NG) operation can reduce the dependence on petroleum-based fuels and curtail greenhouse gas emissions. Such an engine was converted to premixed NG spark-ignition (SI) operation through the addition of a gas injector in the intake manifold and of a spark plug in place of the diesel injector. Engine performance and combustion characteristics were investigated at several lean-burn operating conditions that changed fuel composition, spark timing, equivalence ratio, and engine speed. While the engine operation was stable, the reentrant bowl-in-piston (a characteristic of a CI engine) influenced the combustion event such as producing a significant late combustion, particularly for advanced spark timing. This was due to an important fraction of the fuel burning late in the squish region, which affected the end of combustion, the combustion duration, and the cycle-to-cycle variation. However, the lower cycle-to-cycle variation, stable combustion event, and the lack of knocking suggest a successful conversion of conventional diesel engines to NG SI operation using the approach described here.

scholarly journals Impact of injection strategies on combustion characteristics, efficiency and emissions of gasoline compression ignition operation in a heavy-duty multi-cylinder engine

2018 ◽  
Vol 21 (8) ◽  
pp. 1426-1440 ◽  
Author(s):  
Buyu Wang ◽  
Michael Pamminger ◽  
Ryan Vojtech ◽  
Thomas Wallner
Keyword(s):  
High Temperature ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Pressure Rise ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Temperature Combustion ◽  
Gas Recirculation ◽  
Direct Fuel Injection

Gasoline compression ignition using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low-temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high-temperature combustion with reduced amounts of exhaust gas recirculation appears more practical. Furthermore, for high-temperature gasoline compression ignition, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high-temperature gasoline compression ignition combustion with port and direct injection. Engine testing was conducted at an engine speed of 1038 r/min and brake mean effective pressure of 1.4 MPa for three injection strategies, late pilot injection, early pilot injection, and port/direct fuel injection. The impact on engine performance and emissions with respect to varying the combustion phasing were quantified within this study. At the same combustion phasing, early pilot injection and port/direct fuel injection had an earlier start of combustion and higher maximum pressure rise rates than late pilot injection attributable to more premixed fuel from pilot or port injection; however, brake thermal efficiencies were higher with late pilot injection due to reduced heat transfer. Early pilot injection also exhibited the highest cylinder-to-cylinder variations due to differences in injector behavior as well as the spray/wall interactions affecting mixing and evaporation process. Overall, peak brake thermal efficiency of 46.1% and 46% for late pilot injection and port/direct fuel injection was achieved comparable to diesel baseline (45.9%), while early pilot injection showed the lowest brake thermal efficiency (45.3%).

Operating Characteristics of Natural Gas Fueled Homogeneous Charge Compression Ignition Engine

1999 ◽  
Author(s):  
Y. Kawabata ◽  
K. Nakagawa ◽  
F. Shoji
Keyword(s):  
Natural Gas ◽  
Homogeneous Charge Compression Ignition ◽  
Nox Emission ◽  
Compression Ignition ◽  
Operating Characteristics ◽  
Compression Ignition Engine ◽  
Gas Engine ◽  
Engine Combustion ◽  
Gas Fueled ◽  
Homogeneous Charge

Abstract Recently, a new design of engine combustion that achieves higher efficiency and less NOx emission has been proposed. Some researchers have started studying the concept, which is called Homogeneous Charge Compression Ignition (HCCI), but there have been few reports on investigations using a future prospective alternative fuel, natural gas. In this study, natural gas fueled operation of HCCI using a single cylinder gas engine was conducted. Operating and exhaust characteristics were obtained. Experimental data confirmed the potential of higher efficiency and less NOx emission, though THC and CO were higher. Based on these data, the feasibility of this concept for gas engines is also examined.

Assessment of a Syngas-Diesel Dual Fuelled Compression Ignition Engine

2010 ◽  
Author(s):  
Bibhuti B. Sahoo ◽  
Niranjan Sahoo ◽  
Ujjwal K. Saha
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Gas Flow ◽  
Direct Injection ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Exhaust Gas Temperature

Synthesis gas (Syngas), a mixture of hydrogen and carbon monoxide, can be manufactured from natural gas, coal, petroleum, biomass, and even from organic wastes. It can substitute fossil diesel as an alternative gaseous fuel in compression ignition engines under dual fuel operation route. Experiments were conducted in a single cylinder, constant speed and direct injection diesel engine fuelled with syngas-diesel in dual fuel mode. The engine is designed to develop a power output of 5.2 kW at its rated speed of 1500 rpm under variable loads with inducted syngas fuel having H2 to CO ratio of 1:1 by volume. Diesel fuel as a pilot was injected into the engine in the conventional manner. The diesel engine was run at varying loads of 20, 40, 60, 80 and 100%. The performance of dual fuel engine is assessed by parameters such as thermal efficiency, exhaust gas temperature, diesel replacement rate, gas flow rate, peak cylinder pressure, exhaust O2 and emissions like NOx, CO and HC. Dual fuel operation showed a decrease in brake thermal efficiency from 16.1% to a maximum of 20.92% at 80% load. The maximum diesel substitution by syngas was found 58.77% at minimum exhaust O2 availability condition of 80% engine load. The NOx level was reduced from 144 ppm to 103 ppm for syngas-diesel mode at the best efficiency point. Due to poor combustion efficiency of dual fuel operation, there were increases in CO and HC emissions throughout the range of engine test loads. The decrease in peak pressure causes the exhaust gas temperature to rise at all loads of dual fuel operation. The present investigation provides some useful indications of using syngas fuel in a diesel engine under dual fuel operation.

Performance and Emissions Characteristics of Bio-Diesel (B100)-Ignited Methane and Propane Combustion in a Four Cylinder Turbocharged Compression Ignition Engine

2012 ◽  
Vol 134 (8) ◽  
Author(s):  
N. T. Shoemaker ◽  
C. M. Gibson ◽  
A. C. Polk ◽  
S. R. Krishnan ◽  
K. K. Srinivasan
Keyword(s):  
Natural Gas ◽  
Fuel Efficiency ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Propane Combustion ◽  
Compression Ignition Engine ◽  
Engine Knock ◽  
Performance And Emissions ◽  
Cylinder Compression ◽  
Dual Fueling

Different combustion strategies and fuel sources are needed to deal with increasing fuel efficiency demands and emission restrictions. One possible strategy is dual fueling using readily available resources. Propane and natural gas are readily available with the current infrastructure and biodiesel is growing in popularity as a renewable fuel. This paper presents experimental results from dual fuel combustion of methane (as a surrogate for natural gas) and propane as primary fuels with biodiesel pilots in a 1.9 liter, turbocharged, 4-cylinder compression ignition engine at 1800 rev/min. Experiments were performed with different percentage energy substitutions (PES) of propane and methane and at different brake mean effective pressures (BMEP/bmep). Brake thermal efficiency (BTE) and emissions (NOx, HC, CO, CO2, O2 and smoke) were also measured. Maximum PES levels for B100-methane dual fueling were limited to 70% at 2.5 bars bmep and 48% at 10 bars bmep, and corresponding values for B100-propane dual fueling were 64% and 43%, respectively. Maximum PES was limited by misfire at 2.5 bars bmep and the onset of engine knock at 10 bars bmep. Dual fuel BTEs approached straight B100 values at 10 bars bmep while they were significantly lower than B100 values at 2.5 bars bmep. In general, dual fueling was beneficial in reducing NOx and smoke emissions by 33% and 50%, respectively, from baseline B100 levels; however, both CO and THC emissions were significantly higher than baseline B100 levels at all PES and loads.

Sign in / Sign up

Export Citation Format

Share Document