Numerical Modeling of Hydrodynamic Impact and Local Slamming Effects

2015 ◽  
Author(s):  
Ali Mohtat ◽  
Ravi Challa ◽  
Solomon C. Yim ◽  
Carolyn Q. Judge
Keyword(s):  
Numerical Method ◽  
Impact Velocity ◽  
High Speed ◽  
Impact Behavior ◽  
Analytical Prediction ◽  
Arbitrary Lagrangian Eulerian ◽  
Hydrodynamic Impact ◽  
Ale Formulation ◽  
Wide Range ◽  
The Impact

Numerical simulation and prediction of short duration hydrodynamic impact loading on a generic wedge impacting a water free-surface is investigated. The fluid field is modeled using a finite element (FE) based arbitrary Lagrangian-Eulerian (ALE) formulation and the structure is modeled using a standard Lagrangian FE approximation. Validation of the numerical method against experimental test data and closed form analytical solutions shows that the ALE-FE/FE continuum approach captures the impact behavior accurately. A detailed sensitivity analysis is conducted to study the role of air compressibility, deadrise angle, and impact velocity in estimation of maximum impact pressures. The pressure field is found to be insensitive to air compressibility effect for a wide range of impact velocities and deadrise angles. A semi-analytical prediction model is developed for estimation of maximum impact pressures that correlates deadrise angle, impact velocity, and a nonlinear interaction term that couples hydrodynamic effects between these parameters. The numerical method is also used to examine the intrinsic physics of water impact on a high-speed planing hull with the goal of predicting slamming loads and resulting motions.

Brain Deformation in Linear Head Impact

2009 ◽  
Author(s):  
Kaveh Laksari ◽  
Kurosh Darvish
Keyword(s):  
Finite Element ◽  
High Speed ◽  
Single Point ◽  
Arbitrary Lagrangian Eulerian ◽  
Brain Deformation ◽  
Ale Formulation ◽  
Point Integration ◽  
Inertial Loading ◽  
Experimental Values ◽  
The Impact

In this study, a 2D model of the head underwent linear impact and the experiments were simulated by finite element models. A cylinder with a diameter of 100mm and height of 20mm was filled with 5% gelatin, which was used as the brain surrogate material. The physical model was mounted onto a High Speed Computer Controlled Impact System to generate inertial loading of approximately 50 G average deceleration. The deformation of the samples was studied through image processing. Finite element (FE) analysis was used to simulate the experiments. The impact tests were modeled with two methods: a Lagrangian formulation with single point integration and an Arbitrary Lagrangian Eulerian (ALE) formulation with single point integration and void using LS-Dyna FE code. In the model with slip contact, the normal and shear strains reached more than 20% in some regions, which confirmed the risk of axonal injury in the linear impacts applied in this study. It was seen that in the Lagrangian models, in order to stabilize the simulation, high bulk moduli needed to be used; however, this resulted in much smaller void generation in the posterior region of the model. It was shown that the void generation reaches the experimental values by introducing 1–2 mm initial gaps between brain and skull. The ALE model was more stable and less sensitive to the bulk modulus, but showed smaller deformations.

scholarly journals Air mediates the impact of a compliant hemisphere on a rigid smooth surface

Soft Matter ◽  
2021 ◽  
Author(s):  
Siqi Zheng ◽  
Sam Dillavou ◽  
John M. Kolinski
Keyword(s):  
Elastic Body ◽  
Elastic Properties ◽  
Impact Velocity ◽  
Solid Surface ◽  
High Speed ◽  
Smooth Surface ◽  
High Speed Imaging ◽  
The Impact ◽  
Rigid Smooth

When a soft elastic body impacts upon a smooth solid surface, the intervening air fails to drain, deforming the impactor. High-speed imaging with the VFT reveal rich dynamics and sensitivity to the impactor's elastic properties and the impact velocity.

scholarly journals A smart passive MR damper with a hybrid powering system for impact mitigation: An experimental study

2021 ◽  
pp. 1045389X2098808
Author(s):  
S. Jin ◽  
L. Deng ◽  
J. Yang ◽  
S. Sun ◽  
D. Ning ◽  
...  
Keyword(s):  
Impact Velocity ◽  
Mr Damper ◽  
Damping Force ◽  
Softening Effect ◽  
Impact Speed ◽  
Impact Mitigation ◽  
Passive Damper ◽  
Comparison Results ◽  
Wide Range ◽  
The Impact

This paper presents a smart passive MR damper with fast-responsive characteristics for impact mitigation. The hybrid powering system of the MR damper, composed of batteries and self-powering component, enables the damping of the MR damper to be negatively proportional to the impact velocity, which is called rate-dependent softening effect. This effect can keep the damping force as the maximum allowable constant force under different impact speed and thus improve the efficiency of the shock energy mitigation. The structure, prototype and working principle of the new MR damper are presented firstly. Then a vibration platform was used to characterize the dynamic property and the self-powering capability of the new MR damper. The impact mitigation performance of the new MR damper was evaluated using a drop hammer and compared with a passive damper. The comparison results demonstrate that the damping force generated by the new MR damper can be constant over a large range of impact velocity while the passive damper cannot. The special characteristics of the new MR damper can improve its energy dissipation efficiency over a wide range of impact speed and keep occupants and mechanical structures safe.

Diamond-Like Carbon Coating—It'S Application for Polymeric Substrates

1991 ◽  
Vol 239 ◽  
Author(s):  
Fred M. Kimock ◽  
Alex J. Hsieh ◽  
Peter G. Dehmer ◽  
Pearl W. Yip
Keyword(s):  
High Speed ◽  
Protective Coatings ◽  
Ion Beam ◽  
Chemical Exposure ◽  
Optical Systems ◽  
Impact Behavior ◽  
Organic Liquids ◽  
Diamond Like Carbon ◽  
Dlc Coating ◽  
The Impact

ABSTRACTWe report on a recently commercialized Diamond-Like Carbon (DLC) coating that has been deposited on polycarbonate at near room temperature, via a unique ion beam system. Aspects of high speed impact behavior, chemical resistance, abrasion resistance, and thermal stability of the coating are examined. Results of scanning electron microscopy studies indicate that adhesion of the DLC coating is very good; no delamination of the coating was found on ballistically tested specimens. The well-bonded DLC coating did not cause the impact performance of polycarbonate to become brittle. Chemical exposure test results show that the DLC coating is capable of protecting polycarbonate from chemical attack by aggressive organic liquids. These ion beam deposited DLC coatings have considerable potential as protective coatings for optical systems.

Experimental investigation of the quasi-static and impact tests on the energy absorption characteristics of coupler rubber buffers used in railway vehicles

2018 ◽  
Vol 233 (9) ◽  
pp. 937-950 ◽  
Author(s):  
Shuguang Yao ◽  
Zhixiang Li ◽  
Wen Ma ◽  
Ping Xu ◽  
Quanwei Che
Keyword(s):  
Energy Absorption ◽  
Impact Velocity ◽  
High Speed ◽  
Compression Tests ◽  
Static Compression ◽  
Static Tests ◽  
Impact Tests ◽  
High Speed Trains ◽  
The Impact ◽  
Absorption Characteristics

Coupler rubber buffers are widely used in high-speed trains, to dissipate the impact energy between vehicles. The rubber buffer consists of two groups of rubbers, which are pre-compressed and then installed into the frame body. This paper specifically focuses on the energy absorption characteristics of the rubber buffers. Firstly, quasi-static compression tests were carried out for one and three pairs of rubber sheets, and the relationship between the energy absorption responses, i.e. Eabn  =  n ×  Eab1, Edissn =  n ×  Ediss1, and Ean =  Ea1, was obtained. Next, a series of quasi-static tests were performed for one pair of rubber sheet to investigate the energy absorption performance with different compression ratios of the rubber buffers. Then, impact tests with five impact velocities were conducted, and the coupler knuckle was destroyed when the impact velocity was 10.807 km/h. The results of the impact tests showed that with the increase of the impact velocity, the Eab, Ediss, and Ea of the rear buffer increased significantly, but the three responses of the front buffer did not increase much. Finally, the results of the impact tests and quasi-static tests were contrastively analyzed, which showed that with the increase of the stroke, the values of Eab, Ediss, and Ea increased. However, the increasing rates of the impact tests were higher than that of the quasi-static tests. The maximum value of Ea was 68.76% in the impact tests, which was relatively a high value for the vehicle coupler buffer. The energy capacity of the rear buffer for dynamic loading was determined as 22.98 kJ.

scholarly journals Experimental and Numerical Impact Analysis of Automotive Bumper Brackets Made of 2D Triaxially Braided CFRP Composites

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3554
Author(s):  
Robert Böhm ◽  
Andreas Hornig ◽  
Tony Weber ◽  
Bernd Grüber ◽  
Maik Gude
Keyword(s):  
High Speed ◽  
Impact Analysis ◽  
Damage Model ◽  
Drop Tower ◽  
Structural Deformation ◽  
Impact Behavior ◽  
Speed Test ◽  
Damage Models ◽  
The Impact ◽  
Carbon Fiber Epoxy

The impact behavior of carbon fiber epoxy bumper brackets reinforced with 2D biaxial and 2D triaxial braids was experimentally and numerically analyzed. For this purpose, a phenomenological damage model was modified and implemented as a user material in ABAQUS. It was hypothesized that all input parameters could be determined from a suitable high-speed test program. Therefore, novel impact test device was designed, developed and integrated into a drop tower. Drop tower tests with different impactor masses and impact velocities at different bumper bracket configurations were conducted to compare the numerically predicted deformation and damage behavior with experimental evidence. Good correlations between simulations and tests were found, both for the global structural deformation, including fracture, and local damage entities in the impact zone. It was proven that the developed phenomenological damage models can be fully applied for present-day industrial problems.

Numerical Simulation of the Cold Spray Deposition Process for Aluminium and Copper

2012 ◽  
Author(s):  
Jing Xie ◽  
Daniel Nelias ◽  
Hélène Walter-le Berre ◽  
Yuji Ichikawa ◽  
Kazuhiro Ogawa
Keyword(s):  
Reference Frame ◽  
Cold Spray ◽  
High Speed ◽  
Gas Flow ◽  
Heat Dissipation ◽  
Spray Deposition ◽  
Deposition Process ◽  
Arbitrary Lagrangian Eulerian ◽  
Systematic Analysis ◽  
The Impact

Cold spray is a rapidly developing coating technology for depositing materials in the solid state. In this deposition process, the spray particles are accelerated to a high velocity by a high-speed gas flow, and then form a dense and high quality coating due to plastic deformation of particles impinged upon the solid surface of substrate. 2D and 3D modelling of particle impacting behaviours in cold spray deposition process by using ABAQUS/Explicit was conducted for four couples of materials (i.e. impacting particle/impacted substrate): copper/aluminium, aluminium/copper, copper/copper, and aluminium/aluminium. A systematic analysis of a single impact was carried out considering different parameters, such as the initial impact velocity, initial temperature and contact angle, which affect the deposition process and subsequently the mechanical properties of coating. Three numerical methods have been evaluated and their performances are discussed for various simulation settings: (i) modelling in a Lagrangian reference frame; (ii) modelling using adaptive remeshing in an Arbitrary Lagrangian Eulerian (ALE) reference frame; and (iii), modelling in a CEL reference frame. It is found that the Coupled Eulerian Lagrangian (CEL) method has more advantages to simulate the large deformation of materials, and is also more efficient to prevent the excessive distortion of the mesh. A comparison between simulation results and experimental data from the literature was performed. Nevertheless, the CEL method is implicitly isothermal for ABAQUS v6.10, whereas the modelling in the classical Lagrangian reference frame does include coupled thermo-mechanical effects with a local increase of the temperature near the interface — due to friction — and for the highly plastically deformed elements — due to the heat dissipation linked to plasticity. A local rise of temperature at the impact surface may also be observed for oblique impacts. Finally a first attempt to simulate the deposition of several particles is made with a 3D CEL model, resulting in the creation of porosity at the interface between particles.

Free Space Optical Communication System under Different Weather Conditions

2019 ◽  
Vol 0 (0) ◽  
Author(s):  
Mohammad Yawar Wani ◽  
Hitesh Pathak ◽  
Karamjit Kaur ◽  
Anil Kumar
Keyword(s):  
Attenuation Coefficient ◽  
Optical Communication ◽  
Free Space ◽  
Communication Systems ◽  
High Speed ◽  
Free Space Optical Communication ◽  
Free Space Optical ◽  
Wide Range ◽  
Space Optical Communication ◽  
The Impact

AbstractFree space optical communication systems (FSO’s) have surfaced as admired means of communication in the past few years. High speed of operation, low bandwidth requirements and system reliability are the major factors responsible for their wide range of applications. These communication systems use air as a medium of transmission. Since there is no component like fiber or cable, but air is only medium, the variations in atmospheric conditions play a vital role in performance of these networks. The reason behind is that the conditions like presence of humidity, haze, snowfall, rain, dust or smoke changes the attenuation coefficient of medium. The raised attenuation levels results in increased losses and need to be carefully monitored. The present work analyzes the influence of rain on the performance of FSO network in terms of quality of transmission. The paper discusses the impact of rainfall on attenuation coefficient of air. Then impact of this attenuation on network transmission is presented in terms of BER and Q-factor. In order to demonstrate the impact, BER and Q-value is calculated for 10 Gbps FSO link for clear weather and rainfall conditions.

Improved Two-Dimensional Dynamic Stall Prediction with Structured and Hybrid Numerical Methods

2011 ◽  
Vol 56 (4) ◽  
pp. 1-12 ◽  
Author(s):  
K. Richter ◽  
A. Le Pape ◽  
T. Knopp ◽  
M. Costes ◽  
V. Gleize ◽  
...  
Keyword(s):  
Numerical Methods ◽  
Numerical Method ◽  
High Speed ◽  
Turbulence Modeling ◽  
Turbulence Models ◽  
Boundary Layer Transition ◽  
Dynamic Stall ◽  
Two Dimensional ◽  
Layer Transition ◽  
The Impact

A joint comprehensive validation activity on the structured numerical method elsA and the hybrid numerical method TAU was conducted with respect to dynamic stall applications. To improve two-dimensional prediction, the influence of several factors on the dynamic stall prediction was investigated. The validation was performed for three deep dynamic stall test cases of the rotor blade airfoil OA209 against experimental data from two-dimensional pitching airfoil experiments, covering low-speed and high-speed conditions. The requirements for spatial discretization and for temporal resolution in elsA and TAU are shown. The impact of turbulence modeling is discussed for a variety of turbulence models ranging from one-equation Spalart–Allmaras-type models to state-of-the-art, seven-equation Reynolds stress models. The influence of the prediction of laminar/turbulent boundary layer transition on the numerical dynamic stall simulation is described. Results of both numerical methods are compared to allow conclusions to be drawn with respect to an improved prediction of dynamic stall.

Sign in / Sign up

Export Citation Format

Share Document