scholarly journals Heat transfer and entropy generation for natural convection by adiabatic obstacles inside a cavity heated on the left side

2020 ◽  
Vol 48 (4) ◽  
pp. 825-832
Author(s):  
Jamal Baliti ◽  
Mohamed Hssikou ◽  
Youssef Elguennouni ◽  
Ahmed Moussaoui ◽  
Mohammed Alaoui
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Entropy Generation ◽  
Temperature Gradients ◽  
Large Temperature ◽  
Square Cavity ◽  
Transfer Rates ◽  
Thermal Fields ◽  
Rayleigh Numbers

By using finite difference method, the problem of heat transfer and entropy generation for natural convection of a fluid inside a square cavity with inner adiabatic bodies has been investigated numerically. Calculations have been made for Rayleigh numbers ranging from 102 to 5·104 for two obstacles with different heights. Results are presented as streamlines, isotherm contours and Nusselt number for Prandtl number of 0.71 (assuming the cavity is filled with air). The obtained results demonstrate the effects of pertinent parameters on the fluid flow, thermal fields and heat transfer inside the cavity. The results show that the heat transfer rates generally increase with the shrink of the obstacle size and with the increase of Rayleigh number. The entropy generation is higher at locations with large temperature gradients. Excellent agreement is obtained with previous results in the literature.

Laminar Natural Convection Heat Transfer in a Differentially Heated Square Cavity Due to a Thin Fin on the Hot Wall

2003 ◽  
Vol 125 (4) ◽  
pp. 624-634 ◽  
Author(s):  
Xundan Shi ◽  
J. M. Khodadadi
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Computational Study ◽  
Convection Heat Transfer ◽  
Square Cavity ◽  
Left Wall ◽  
Flow Modification ◽  
Laminar Natural Convection ◽  
Rayleigh Numbers ◽  
Blockage Effect

A finite-volume-based computational study of steady laminar natural convection (using Boussinesq approximation) within a differentially heated square cavity due to the presence of a single thin fin is presented. Attachment of highly conductive thin fins with lengths equal to 20, 35 and 50 percent of the side, positioned at 7 locations on the hot left wall were examined for Ra=104,105,106, and 107 and Pr=0.707 (total of 84 cases). Placing a fin on the hot left wall generally alters the clockwise rotating vortex that is established due to buoyancy-induced convection. Two competing mechanisms that are responsible for flow and thermal modifications are identified. One is due to the blockage effect of the fin, whereas the other is due to extra heating of the fluid that is accommodated by the fin. The degree of flow modification due to blockage is enhanced by increasing the length of the fin. Under certain conditions, smaller vortices are formed between the fin and the top insulated wall. Viewing the minimum value of the stream function field as a measure of the strength of flow modification, it is shown that for high Rayleigh numbers the flow field is enhanced regardless of the fin’s length and position. This suggests that the extra heating mechanism outweighs the blockage effect for high Rayleigh numbers. By introducing a fin, the heat transfer capacity on the anchoring wall is always degraded, however heat transfer on the cold wall without the fin can be promoted for high Rayleigh numbers and with the fins placed closer to the insulated walls. A correlation among the mean Nu, Ra, fin’s length and its position is proposed.

Numerical Simulation of Natural Convection Flow in a Cube With a Horizontal Heated Strip

2008 ◽  
Author(s):  
Esam M. Alawadhi
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Nusselt Number ◽  
High Temperature ◽  
Natural Convection ◽  
Vertical Wall ◽  
Convection Flow ◽  
Front Wall ◽  
Natural Convection Flow ◽  
Rayleigh Numbers

Natural convection flow in a cube with a heated strip is solved numerically. The heated strip is attached horizontally to the front wall and maintained at high temperature, while the entire opposite wall is maintained at low temperature. The heated strip simulates an array of electronic chips The Rayleigh numbers of 104, 105, and 106 are considered in the analysis and the heated strip is horizontally attached to the wall. The results indicate that the heat transfer strongly depends on the position of the heated strip. The maximum Nusselt number can be achieved if the heater is placed at the lower half of the vertical wall. Increasing the Rayleigh number significantly promotes heat transfer in the enclosure. Flow streamlines and temperature contours are presented, and the results are validated against published works.

Effects of Thermal Boundary Conditions on Entropy Generation During Natural Convection in a Differentially Heated Square Cavity

2010 ◽  
Author(s):  
Ram Satish Kaluri ◽  
Tanmay Basak ◽  
A. R. Balakrishnan
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Boundary Conditions ◽  
Entropy Generation ◽  
Bottom Wall ◽  
Convection Flow ◽  
Uniform Heating ◽  
Square Cavity ◽  
Fluid Friction ◽  
Thermal Boundary Conditions

Natural convection is a widely occurring phenomena which has important applications in material processing, energy storage devices, electronic cooling, building ventilation etc. The concept of ‘entropy generation minimization’, which is a thermodynamic approach for optimization, may be very useful in designing efficient thermal systems. In the current study, entropy generation in steady laminar natural convection flow in a square cavity is studied with following isothermal boundary conditions: (1) Bottom wall is uniformly heated (2) Bottom wall is sinusoidally heated. The side walls are maintained cold and the top wall is maintained adiabatic. The thermal boundary condition in non-uniform heating case (case 2) is such that the dimensionless average temperature of the bottom wall is equal to that of uniform heating case (case 1). The prime objective of this work is to investigate the influence of uniform and non-uniform heating on entropy generation. The governing mass, momentum and energy equations are solved using Galerkin finite element method. Streamlines, isotherms, contour maps of entropy generation due to heat transfer and fluid friction are studied for Pr = 0.01 (molten metals) and 7 (water) in range of Ra = 103–105. Detailed analysis on the effect of uniform and non-uniform thermal boundary conditions on entropy generation due to heat transfer and fluid friction has been presented. Also, the average Bejan’s number which indicates the relative dominance of entropy generation due to heat transfer or fluid friction and the total entropy generation are studied for each case.

Laminar Natural Convection Heat Transfer From a Horizontal Circular Cylinder to Liquid Metals

1991 ◽  
Vol 113 (1) ◽  
pp. 91-96 ◽  
Author(s):  
K. Sugiyama ◽  
Y. Ma ◽  
R. Ishiguro
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Circular Cylinder ◽  
Liquid Metals ◽  
Convection Heat Transfer ◽  
Boussinesq Approximation ◽  
Large Temperature ◽  
Transfer Rates ◽  
Laminar Natural Convection ◽  
Horizontal Circular Cylinder

The objective of the present study is to clarify the heat transfer characteristics of natural convection around a horizontal circular cylinder immersed in liquid metals. Experimental work concerning liquid metals sometimes involves such a degree of error that it is impossible to understand the observed characteristics in a measurement. Numerical analysis is a powerful means to overcome this experimental disadvantage. In the present paper we first show that the Boussinesq approximation is more applicable to liquid metals than to ordinary fluids and that the present analysis gives accurate heat transfer rates, even for a cylinder with a relatively large temperature difference (>100 K) between the heat transfer surface and fluid. It is found from a comparison of the present results with previous work that the correlation equations that have already been proposed predict values lower than the present ones.

Natural Convection Inside a Square Cavity Heated From Below and Symmetrically Cooled at Both Sides: Effects of Various Dirichlet Boundary Conditions at the Bottom Wall

2005 ◽  
Author(s):  
Satyajit Roy ◽  
Tanmay Basak
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Boundary Conditions ◽  
Transfer Rate ◽  
Dirichlet Boundary ◽  
Dirichlet Boundary Conditions ◽  
Bottom Wall ◽  
Uniform Heating ◽  
Square Cavity ◽  
Rayleigh Numbers

A numerical study is performed to investigate the steady laminar natural convection flow in a square cavity with uniformly and non-uniformly heated bottom wall, and adiabatic top wall maintaining constant temperature of cold vertical walls. A penalty finite element method with bi-quadratic rectangular elements has been used to solve the governing mass, momentum and energy equations. The numerical procedure adopted in the present study yields consistent performance over the range of parameters (Rayleigh number Ra, 103 ≤ Ra ≤ 105 and Prandtl number Pr, 0.7 ≤ Pr ≤ 10) with respect to continuous and discontinuous Dirichlet boundary conditions. Non-uniform heating of the bottom wall produces greater heat transfer rate at the center of the bottom wall than uniform heating case for all Rayleigh numbers but average Nusselt number shows overall lower heat transfer rate for non-uniform heating case. Critical Rayleigh numbers for conduction dominant heat transfer cases have been obtained.

Numerical Investigation of Variable Property Effects on Laminar Natural Convection of Gases Between Two Horizontal Isothermal Concentric Cylinders

1986 ◽  
Vol 108 (4) ◽  
pp. 783-789 ◽  
Author(s):  
D. N. Mahony ◽  
R. Kumar ◽  
E. H. Bishop
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Boussinesq Approximation ◽  
Variable Properties ◽  
Transfer Rates ◽  
Concentric Cylinders ◽  
Weighted Mean Temperature ◽  
Laminar Natural Convection ◽  
Rayleigh Numbers ◽  
Gap Width

A numerical finite difference investigation has been conducted to determine the effects of variable properties on the laminar natural convection of gases between horizontal isothermal concentric cylinders. Velocity profiles, temperature profiles, and heat transfer rates have been computed for diameter ratios of 1.5, 2.28, 2.6, and 5.0 and Rayleigh numbers based on gap width up to 1.8 × 105. The temperature difference ratio θo was varied from 0.2 to 3.0, and the range of validity of the Boussinesq approximation was determined to be θo = 0.2. A volume-weighted mean temperature was shown to be the most effective reference temperature to reduce the heat transfer data for each diameter ratio to a single curve of the form keq = C RaLn, for 0.2 ≤ θo ≤ 3.0 and RaL = 2.0 × 105.

A Numerical Study of Natural Convection in a Cavity With Two Fins Attached to Its Vertical Walls

2007 ◽  
Author(s):  
G. A. Sheikhzadeh ◽  
M. Pirmohammadi ◽  
M. Ghassemi
Keyword(s):  
Nusselt Number ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Numerical Study ◽  
Convection Heat Transfer ◽  
Square Cavity ◽  
Vertical Walls ◽  
The Mean ◽  
Energy Equations ◽  
Rayleigh Numbers

Numerical study natural convection heat transfer inside a differentially heated square cavity with adiabatic horizontal walls and vertical isothermal walls is investigated. Two perfectly conductive thin fins are attached to the isothermal walls. To solve the governing differential mass, momentum and energy equations a finite volume code based on Pantenkar’s simpler method is developed and utilized. The results are presented in form of streamlines, isotherms as well as Nusselt number for Rayleigh number ranging from 104 up to 107. It is shown that the mean Nusselt number is affected by the position of the fins and length of the fins as well as the Rayleigh number. It is also observed that maximum Nusselt number occurs about the middle of the enclosure where Lf is grater the 0.5. In addition the Nusselt number stays constant and does not varies with width of the cavity (lf) when Lf is equal to 0.5 and Rayleigh number is equal to 104 and 107 as well as when Lf is equal to 0.6 and low Rayleigh numbers.

scholarly journals Effect of Various Tilted Positions of a Thin Fin on Natural Convection of Laminar Viscous Flow in a Square Cavity

2021 ◽  
Vol 39 (5) ◽  
pp. 1634-1642
Author(s):  
Syed Fazuruddin ◽  
Seelam Sreekanth ◽  
G Sankara Sekhar Raju
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Finite Difference ◽  
Average Nusselt Number ◽  
Vertical Position ◽  
Inclination Angles ◽  
Rayleigh Numbers

An exhaustive numerical investigation is carried out to analyze the role of an isothermal heated thin fin on fluid flow and temperature distribution visualization in an enclosure. Natural convection within square enclosures finds remarkable pragmatic applications. In the present study, a finite difference approach is performed on two-dimensional laminar flow inside an enclosure with cold side walls and adiabatic horizontal walls. The fluid flow equations are reconstructed into vorticity - stream function formulation and these equations are employed utilizing the finite-difference strategy with incremental time steps. The parametric study includes a wide scope of Rayleigh number, Ra, and inclination angle ϴ of the thin fin. The effect of different Rayleigh numbers ranging Ra = 104-106 with Pr=0.71 for all the inclination angles from 0°-360° with uniform rotational length of angle 450 of an inclined heated fin on fluid flow and heat transfer have been investigated. The heat transfer rate within the enclosure is measured by means of local and average Nusselt numbers. Regardless of inclination angles of the thin fin, a slight enhancement in the average Nusselt number is observed when Rayleigh number increased for both the cases of the horizontal and vertical position of the thin fin. When the fin has inclined no change in average Nusselt number is noticed for distinct Rayleigh numbers.

MHD natural convection and entropy analysis of a nanofluid inside T-shaped baffled enclosure

2018 ◽  
Vol 28 (12) ◽  
pp. 2916-2941 ◽  
Author(s):  
Taher Armaghani ◽  
A. Kasaeipoor ◽  
Mohsen Izadi ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Entropy Generation ◽  
Hartmann Number ◽  
Content Type ◽  
Thermal Indexes ◽  
The Impact

Purpose The purpose of this paper is to numerically study MHD natural convection and entropy generation of Al2O3-water alumina nanofluid inside of T-shaped baffled cavity which is subjected to a magnetic field. Design/methodology/approach Effect of various geometrical, fluid and flow factors such as aspect ratio of enclosure and baffle length, Rayleigh and Hartmann number of nanofluid have been considered in detail. The hydrodynamics and thermal indexes of nanofluid have been described using streamlines, isotherms and isentropic lines. Findings It is found that by enhancing Hartmann number, symmetrical streamlines gradually lose symmetry and their values decline. It is found that by enhancing Hartmann number, symmetrical streamlines gradually lose symmetry and their values decline. The interesting finding is an increase in the impact of Hartmann number on heat transfer indexes with augmenting Rayleigh number. However, with augmenting Rayleigh number and, thus, strengthening the buoyant forces, the efficacy of Hartmann number one, an index indicating the simultaneous impact of natural heat transfer to entropy generation increases. It is clearly seen that the efficacy of nanofluid on increased Nusselt number enhances with increasing aspect ratio of the enclosure. Based on the results, the Nusselt number generally enhances with the larger baffle length in the enclosure. Finally, with larger Hartmann number and lesser Nusselt one, entropy production is reduced. Originality/value The authors believe that all the results, both numerical and asymptotic, are original and have not been published elsewhere.

Sign in / Sign up

Export Citation Format

Share Document