Investigation of cutting temperatures distribution in machining heat treated medium carbon steel on a lathe.

2012 ◽  
Vol 4 (1) ◽  
Author(s):  
A. G. F. Alabi
Keyword(s):  
Carbon Steel ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Heat Treated

scholarly journals Mechanical Properties of Heat-treated Medium Carbon Steel in Renewable and Biodegradable Oil

2019 ◽  
Vol 35 ◽  
pp. 229-235 ◽  
Author(s):  
Oluwagbenga T. Johnson ◽  
Enoch N. Ogunmuyiwa ◽  
Albert U. Ude ◽  
Norman Gwangwava ◽  
Richard Addo-Tenkorang
Keyword(s):  
Mechanical Properties ◽  
Carbon Steel ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Heat Treated

scholarly journals The morphology of cavitation damage of heat-treated medium carbon steel

2006 ◽  
Vol 71 (8-9) ◽  
pp. 977-984 ◽  
Author(s):  
Marina Dojcinovic ◽  
Srdjan Markovic
Keyword(s):  
Carbon Steel ◽  
Cavitation Erosion ◽  
Medium Carbon Steel ◽  
Cavitation Damage ◽  
Medium Carbon ◽  
Erosion Rates ◽  
Hydraulic Machinery ◽  
Heat Treated ◽  
Set Up ◽  
Microscopy Techniques

In this paper the morphology of the cavitation damage to heat-treated medium carbon steel was analyzed. The experiments were conducted using a modified vibratory cavitation test set up. The erosion rates were measured by an analytical method. The morphology of the cavitation damage was studied by the scanning electron microscopy and optical microscopy techniques. The present work was aimed at understanding the cavitation erosion behavior of heat-treated medium carbon steel under laboratory conditions. The results indicate that the heat-treated medium carbon steel is not to be recommended for the production of hydraulic machinery parts exposed to high hydrodynamic intensity.

Effects of NaBH4 and Heat-Treat on Corrosion Resistance of Electroless Plating Ni-B Coating

2014 ◽  
Vol 809-810 ◽  
pp. 604-609
Author(s):  
Chu Xu Dong ◽  
Wan Chang Sun ◽  
Ju Mei Zhang ◽  
Hui Cai ◽  
Li Bin Niu
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Low Temperature ◽  
Composite Coating ◽  
Electroless Plating ◽  
Composite Coatings ◽  
Medium Carbon Steel ◽  
Plating Bath ◽  
Medium Carbon ◽  
Heat Treated

Ni-B/Ni-B-B4C composite coatings on the substrate of medium-carbon steel (45#) were successfully fabricated by electroless plating in a low temperature bath. The corrosion resistance of Ni-B coating were examined by using electrochemical workstation. The results indicated that there are no pores and cracks and other defects at the interface between the substrate and composite coating. It was found that the corrosion resistance of Ni-B coating increased and then decreased with the addition of NaBH4 increasing, and the best addition in plating bath was about 0.9 g/L. While the corrosion resistance of Ni-B coating heat-treated at 400°C with NaBH4 addition 0.9 g/L was the worst.

Preparation of Ultra-Fine MgO•Al2O3 Spinel Powder and its Metallurgy Behavior in Medium Carbon Steel

2009 ◽  
Vol 79-82 ◽  
pp. 111-114 ◽  
Author(s):  
Yang Li ◽  
Wei Jun Zhi ◽  
Wei Jian Li ◽  
Liang You Wang ◽  
Zhou Hua Jiang
Keyword(s):  
Carbon Steel ◽  
Spinel Phase ◽  
Sol Gel ◽  
Fine Powder ◽  
Xrd Analysis ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Heat Treated ◽  
Average Size ◽  
Spinel Powder

Micron, sub-micron and nanometer sized MgO•Al2O3 ultra-fine powders were prepared by gel precipitation, solid-phrase synthesis, sol-gel and flame throwing pyrogenation methods. XRD analysis shows that the all of the ultra-fine powder is pure with a single MgO•Al2O3 spinel phase. The size is measured by laser granularity analyzer and the average size is 60, 505 and 1780 nm with quite uniform distribution. MgO•Al2O3 spinel powder with different granularity were sprayed into molten medium carbon steel in MgO crucible and MoSi2 furnace at 1873 K. Quantitative microscopic examination shows that big particle inclusions are reduced and small particle inclusions increased, and the average size is reduced. Data comparison from spraying different size powders shows that spraying MgO•Al2O3 of nanometer tends to cause more small inclusions. The sprayed steel samples were rolled and heat treated for the mechanical properties tests, which shows spraying nanometer MgO•Al2O3 is the best way to improve mechanical property.

scholarly journals Investigation of Heat Treatment on Mechanical Properties of Medium Carbon Steel

2021 ◽  
pp. 90-95
Author(s):  
R. Suresh
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Carbon Steel ◽  
Heat Treatments ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Standard Methods ◽  
Quenching Media ◽  
Heat Treated

The effect of various heat treatment operations (annealing, normalizing and hardening) on mechanical properties of medium carbon steel was investigated. The samples were prepared and heat-treated at 770 ºC subsequently was cooled by different quenching media. The mechanical properties of the treated and untreated samples were determined using standard methods. Results showed that the mechanical properties of carbon steel can be changed and improved by various heat treatments. It was also found that the annealed samples has the lowest tensile strength and hardness value and highest ductility, while hardened samples has the highest tensile strength and hardness value and lowest ductility value.

CARPENTER No. 5-317

Alloy Digest ◽  
1955 ◽  
Vol 4 (2) ◽  
Keyword(s):  
Carbon Steel ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Nickel Chromium ◽  
Treated Condition ◽  
Heat Treated ◽  
Heat Treated Condition

Abstract CARPENTER No. 5-317 is a nickel-chromium medium carbon steel for high combination of hardness and toughness in heat treated condition. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on forming, heat treating, machining, and joining. Filing Code: SA-27. Producer or source: Carpenter.

Sign in / Sign up

Export Citation Format

Share Document