scholarly journals Study on the Optimization Field Welding Conditions of Low Heat-Input Pluse MIG Welding Process for 5052 Aluminum Alloy Sheets

2011 ◽  
Vol 29 (1) ◽  
pp. 80-84
Author(s):  
Jae-Seong Kim ◽  
Young-Gi Lee ◽  
Ju-Sun An ◽  
Bo-Young Lee
Keyword(s):  
Aluminum Alloy ◽  
Heat Input ◽  
Welding Process ◽  
Mig Welding

scholarly journals Study the Effect of Welding Heat Input on the Microstructure, Hardness, and Impact Toughness of AISI 1015 Steel

2018 ◽  
Vol 14 (1) ◽  
pp. 118-127 ◽  
Author(s):  
Emad Kh. Hamd ◽  
Abbas Sh. Alwan ◽  
Ihsan Khalaf Irthiea
Keyword(s):  
Corrosion Rate ◽  
Weld Joint ◽  
Heat Input ◽  
Plate Thickness ◽  
Welding Process ◽  
Welding Current ◽  
Low Carbon ◽  
Mig Welding ◽  
The Impact ◽  
Weld Heat

In the present study, MIG welding is carried out on low carbon steel type (AISI 1015) by using electrode ER308L of 1.5mm diameter with direct current straight polarity (DCSP). The joint geometry is of a single V-butt joint with one pass welding stroke for different plate thicknesses of 6, 8, and 10 mm. In welding experiments, AISI 1015 plates with dimensions of 200×100mm and edge angle of 60o from both sides are utilized. In this work, three main parameters related to MIG welding process are investigated, which are welding current, welding speed, heat input and plate thickness, and to achieve that three groups of plates are employed each one consists of three plates. The results indicate that increasing the weld heat input (through changing the current and voltage) leads to an increase in widmanstatten ferrite (WF), acicular ferrite (AF) and polygonal ferrite (PF) in FZ region, and a reduction in grain size. It is observed that the micro-hardness of welded AISI 1015 plate increases as the weld heat input decreases. As well as increasing the weld heat input results in an increase in the width of WM and HAZ and a reduction in the impact energy of the weld joint of AISI 1015 at WM region. Also, it is noted the corrosion rate of weld joint increases with increase of Icorr due to increasing in welding current (heat input), corrosion rate increased up to (0.126µm/yr.) with increasing of heat input up to (1.27 KJ/mm).  

scholarly journals Multi-Objective Optimization of MIG Welding and Preheat Parameters for 6061-T6 Al Alloy T-Joints Using Artificial Neural Networks Based on FEM

Coatings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 998
Author(s):  
Qing Shao ◽  
Fuxing Tan ◽  
Kai Li ◽  
Tatsuo Yoshino ◽  
Guikai Guo
Keyword(s):  
Process Parameters ◽  
Welding Speed ◽  
Heat Input ◽  
Pareto Front ◽  
Welding Process ◽  
Residual Deformation ◽  
Welding Deformation ◽  
Mig Welding ◽  
Preheat Temperature ◽  
Multi Objective

To control the welding residual stress and deformation of metal inert gas (MIG) welding, the influence of welding process parameters and preheat parameters (welding speed, heat input, preheat temperature, and preheat area) is discussed, and a prediction model is established to select the optimal combination of process parameters. Thermomechanical numerical analysis was performed to obtain the residual welding deformation and stress according to a 100 × 150 × 50 × 4 mm aluminum alloy 6061-T6 T-joint. Owing to the complexity of the welding process, an optimal Latin hypercube sampling (OLHS) method was adopted for sampling with uniformity and stratification. Analysis of variance (ANOVA) was used to find the influence degree of welding speed (7.5–9 mm/s), heat input (1500–1700 W), preheat temperature (80–125 °C), and preheat area (12–36 mm). The range of research parameters are according to the material, welding method, thickness of the welding plate, and welding procedure specification. Artificial neural network (ANN) and multi-objective particle swarm optimization (MOPSO) was combined to find the effective parameters to minimize welding deformation and stress. The results showed that preheat temperature and welding speed had the greatest effect on the minimization of welding residual deformation and stress, followed by the preheat area, respectively. The Pareto front was obtained by using the MOPSO algorithm with ε-dominance. The welding residual deformation and stress are the minimum at the same time, when the welding parameters are selected as preheating temperature 85 °C and preheating area 12 mm, welding speed is 8.8 mm/s and heat input is 1535 W, respectively. The optimization results were validated by the finite element (FE) method. The error between the FE results and the Pareto optimal compromise solutions is less than 12.5%. The optimum solutions in the Pareto front can be chosen by designers according to actual demand.

Weld Width Control System for Pulsed MIG Welding of Aluminum Alloy

2011 ◽  
Vol 299-300 ◽  
pp. 908-911
Author(s):  
Li Hui Lu ◽  
Ding Fan ◽  
Jian Kang Huang ◽  
Ming Zhu ◽  
Yu Shi
Keyword(s):  
Aluminum Alloy ◽  
Control System ◽  
Welding Process ◽  
Pulse Method ◽  
High Energy ◽  
Double Pulse ◽  
Mig Welding ◽  
Heat Accumulation ◽  
Weld Width ◽  
Vision Sensing

Due to strong heat accumulation and low surface tension of aluminum alloy, weld width will become wider, even subsidence in pulsed MIG welding process of aluminum alloy at constant parameters. A variable double-pulse method for weld width control is proposed. Weld width control is realized by changing double-pulse duty cycle that is the ratio of high-energy pulse time in a double-pulse cycle to adjust heat input based on the vision sensing for weld width. A rapid prototyping control system is built on the basis of vision sensing and xPC Target real-time environment. Then variable double-pulse MIG welding process test is done and proves the feasibility of the control scheme. On this basis, weld width control test in pulsed MIG welding of aluminum alloy is carried out and obtains a good weld with beautiful formation and uniform weld width. The results show that weld width control can be realized well with the variable double-pulse method in pulsed MIG welding of aluminum alloy.

Comparison between Plasma-MIG and MIG Procedures on 5A06 Aluminum Alloy

2008 ◽  
Vol 575-578 ◽  
pp. 1382-1388 ◽  
Author(s):  
Hong Ming Gao ◽  
Yan Bai ◽  
Lin Wu
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Mechanical Performance ◽  
Weld Zone ◽  
Welding Process ◽  
Deposition Efficiency ◽  
Eutectic Structure ◽  
Melting Rate ◽  
Mig Welding ◽  
5A06 Aluminum Alloy

10mm-5A06 aluminum alloy was butt-welded in a single pass by the plasma-gas metal arc (plasma-MIG) welding procedure, the joints were subjected to X-ray inspection, the microstructure and mechanical performance of weld were also studied. The results indicate that plasma-MIG welding is superior to regular conventional MIG welding on the aspects of reducing weld porosity, increasing joint quality and improving deposition efficiency. Good weld joint with less porosity and excellent mechanical properties is obtained, which can reach as 92.62% tensile strength and 85.12% elongation percentage as base metal. Dimples in which the precipitated phase is the solid solution based on Al3Mg2 are observed in fracture scanning electron micrograph and the fracture mode is ductile rupture. α-Al and Al3Mg2 ,α-Al and eutectic structure are observed respectively in fusion area and in weld zone. The wire feed rate and melting rate can come to 14.5m/min and 80g/min respectively for the 1.6mm welding wire by the plasma-MIG welding process on the premise that the tensile strength of the joints meet the requirements.

scholarly journals Stability and Heat Input Controllability of Two Different Modulations for Double-Pulse MIG Welding

2019 ◽  
Vol 9 (1) ◽  
pp. 127 ◽  
Author(s):  
Jiaxiang Xue ◽  
Min Xu ◽  
Wenjin Huang ◽  
Zhanhui Zhang ◽  
Wei Wu ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Heat Input ◽  
Double Pulse ◽  
Fish Scale ◽  
Input Energy ◽  
Mig Welding ◽  
Pulse Modulation ◽  
Welding Arc ◽  
Input Control ◽  
Welding Processes

Aluminum alloy welding frequently experiences difficulties such as heat input control, poor weld formation, and susceptibility to pore generation. We compared the use of two different modulations for double-pulse metal inert gas (MIG) welding to reduce the heat input required to generate oscillations in the weld pool. The stabilities of rectangular wave-modulated and trapezoidal wave-modulated double-pulse MIG welding (DP-MIG and TP-MIG) were analyzed by examining their welding processes and weld profiles. We found that the transitional pulse in TP-MIG welding results in smoother current transitions, softer welding arc sounds, and a highly uniform fish-scale pattern. Therefore, TP-MIG welding is more stable than DP-MIG welding. The effects of these double-pulse modulation schemes on welding input energy are presented. We propose methods for reducing welding input energy by varying the number of pulses or the pulse base time of low-energy pulse train while keeping the welding current and welding arc stable and unchanged. Compared to DP-MIG welding, TP-MIG welding reduces the input energy by 12% and produces finer grain sizes, which increases weld hardness. Therefore, TP-MIG welding offers a new approach for heat input control in DP-MIG welding of aluminum alloys. The results of this work are significant for aluminum alloy welding.

Sign in / Sign up

Export Citation Format

Share Document