scholarly journals Optimization of Maxillofacial Prosthesis

Prosthesis ◽  
2020 ◽  
Author(s):  
Faraedon M. Zardawi ◽  
Kaida Xiao
Keyword(s):  
Maxillofacial Prosthesis

Eye Replacement by Acrylic Maxillofacial Prosthesis

1945 ◽  
Vol 96 (6) ◽  
pp. 469-478 ◽  
Author(s):  
Phelps J. Murphey ◽  
Leon Schlossberg
Keyword(s):  
Maxillofacial Prosthesis

Disinfectant effects of Brazilian green propolis alcohol solutions on the Staphylococcus aureus biofilm of maxillofacial prosthesis polymers

2021 ◽  
Author(s):  
Mariana Neves de Azevedo ◽  
Nathalia Teixeira Marques ◽  
Maria Fernanda Lopes Fonseca ◽  
Lauren Frenzel Schuch ◽  
José Alcides Almeida de Arruda ◽  
...  
Keyword(s):  
Staphylococcus Aureus ◽  
Maxillofacial Prosthesis ◽  
Brazilian Green Propolis

scholarly journals A Case Report of Maxillofacial Prosthesis

1965 ◽  
Vol 9 (1) ◽  
pp. 94-97
Author(s):  
Yoshihiko Okuno ◽  
Yasushi Ohara ◽  
Norishige Torii
Keyword(s):  
Case Report ◽  
Maxillofacial Prosthesis

Types of Maxillofacial Prosthesis

2003 ◽  
pp. 696-696
Author(s):  
Deepak Veeraiyan ◽  
Karthikeyan Ramalingam ◽  
Vinaya Bhat
Keyword(s):  
Maxillofacial Prosthesis

Three-dimensional printing technologies in the fabrication of maxillofacial prosthesis: A case report

2019 ◽  
Vol 43 (5) ◽  
pp. 343-347 ◽  
Author(s):  
Pinar Cevik ◽  
Mustafa Kocacikli
Keyword(s):  
Case Report ◽  
Three Dimensional ◽  
Acrylic Resin ◽  
Three Dimensional Printing ◽  
Silicone Prosthesis ◽  
Optical Scanner ◽  
Maxillofacial Prosthesis ◽  
Cast Model ◽  
Healthy Side ◽  
Dimensional Printing

Purpose: Patients with maxillofacial deformities always seek for aesthetic prosthesis. Recently, three-dimensional printing technologies have been used for dental treatments on such patients. Case report: A 24-year-old man reported to the Department of Prosthodontics for replacement of his missing right ear induced by a trauma. A magnet-retained auricular prosthesis was planned for the patient. Three-dimensional scanning was performed on the healthy side by using a three-dimensional optical scanner and the data were mirrored. The mirrored image was then imported to a software and a virtual model of the future prosthesis was obtained for the defect side. A three-dimensional printer was used to fabricate a negative mold for the mirrored image by using additive manufacturing. Initially, an impression of the defect side was made; then, the cast model was obtained in a dental flask. Magnets of the prosthesis were inserted to the acrylic resin framework on the cast model. Room temperature vulcanized silicone elastomer was mixed and poured into the three-dimensionally fabricated mold. Then, the flask was placed over the negative mold firmly. After polymerization of the silicone, the auricular prosthesis was delivered to the patient and the patient was instructed to clean the prosthesis daily. Conclusions: Three-dimensional printing technology was used for the fabrication of the patient’s missing ear. This method eliminated the conventional laboratory steps and reduced the number of stages of the fabrication of a silicone prosthesis. The negative mold of the defect side allowed us a direct fabrication of the silicone prosthesis without a need for waxing or flasking procedures.

Sign in / Sign up

Export Citation Format

Share Document