scholarly journals Processing of Graphene/CNT-Metal Powder

2018 ◽  
Author(s):  
Prashantha Kumar HG ◽  
Anthony Xavior M
Keyword(s):  
Metal Powder

ANCORSTEEL 4600V

Alloy Digest ◽  
2012 ◽  
Vol 61 (6) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
Tensile Properties ◽  
Metal Powder ◽  
Heat Treating ◽  
Powder Metal

Abstract Ancorsteel 4600V alloy is a water-atomized low-alloy sinter-hardening metal powder. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as fracture toughness. It also includes information on heat treating and powder metal forms. Filing Code: SA-655. Producer or source: Hoeganaes Corporation.

scholarly journals Carbon Particle In-Situ Alloying of the Case-Hardening Steel 16MnCr5 in Laser Powder Bed Fusion

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 896
Author(s):  
Matthias Schmitt ◽  
Albin Gottwalt ◽  
Jakob Winkler ◽  
Thomas Tobie ◽  
Georg Schlick ◽  
...  
Keyword(s):  
Laser Beam ◽  
Mechanical Strength ◽  
Carbon Content ◽  
Metal Powder ◽  
Case Hardening ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Carbon Particles ◽  
Case Hardening Steel

The carbon content of steel affects many of its essential properties, e.g., hardness and mechanical strength. In the powder bed fusion process of metals using a laser beam (PBF-LB/M), usually, pre-alloyed metal powder is solidified layer-by-layer using a laser beam to create parts. A reduction of the carbon content in steels is observed during this process. This study examines adding carbon particles to the metal powder and in situ alloying in the PBF-LB/M process as a countermeasure. Suitable carbon particles are selected and their effect on the particle size distribution and homogeneity of the mixtures is analysed. The workability in PBF-LB is then shown. This is followed by an evaluation of the resulting mechanical properties (hardness and mechanical strength) and microstructure in the as-built state and the state after heat treatment. Furthermore, potential use cases like multi-material or functionally graded parts are discussed.

Development and characterization of AISI 316L micro parts produced by metal powder hot embossing

2021 ◽  
Vol 113 (1-2) ◽  
pp. 407-417
Author(s):  
Omid Emadinia ◽  
Maria Teresa Vieira ◽  
Manuel Fernando Vieira
Keyword(s):  
Metal Powder ◽  
Hot Embossing ◽  
Aisi 316L ◽  
Micro Parts

scholarly journals Combustion Synthesis of Aluminum Oxynitride in Loose Powder Beds

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4182
Author(s):  
Alan Wilmański ◽  
Magdalena Zarzecka-Napierała ◽  
Zbigniew Pędzich
Keyword(s):  
Combustion Synthesis ◽  
Metal Powder ◽  
Weight Ratio ◽  
Nitrogen Pressure ◽  
Alumina Powder ◽  
Metal Powders ◽  
Aluminum Oxynitride ◽  
Synthesis Conditions ◽  
Aluminum Metal ◽  
Loose Powder

This paper describes combusting loose powder beds of mixtures of aluminum metal powders and aluminum oxide powders with various grain sizes under various nitrogen pressure. The synthesis conditions required at least 20/80 weight ratio of aluminum metal powder to alumina powder in the mix to reach approximately 80 wt% of γ-AlON in the products. Finely ground fused white alumina with a mean grain size of 5 μm was sufficient to achieve results similar to very fine alumina with 0.3 μm grains. A lower nitrogen pressure of 1 MPa provided good results, allowing a less robust apparatus to be used. The salt-assisted combustion synthesis upon addition of 10 wt% of ammonium nitrite resulted in a slight increase in product yield and allowed lower aluminum metal powder content in mixes to be ignited. Increasing the charge mass five times resulted in a very similar γ-AlON yield, providing a promising technology for scaling up. Synthesis in loose powder beds could be utilized for effective production of relatively cheap and uniform AlON powder, which could be easily prepared for forming and sintering without intensive grounding and milling, which usually introduce serious contamination.

Toward Metamodels for Composable and Reusable Additive Manufacturing Process Models

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Paul Witherell ◽  
Shaw Feng ◽  
Timothy W. Simpson ◽  
David B. Saint John ◽  
Pan Michaleris ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Metal Powder ◽  
Manufacturing Process ◽  
Process Model ◽  
Model Development ◽  
Process Models ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Future Work ◽  
Am Processes

In this paper, we advocate for a more harmonized approach to model development for additive manufacturing (AM) processes, through classification and metamodeling that will support AM process model composability, reusability, and integration. We review several types of AM process models and use the direct metal powder bed fusion AM process to provide illustrative examples of the proposed classification and metamodel approach. We describe how a coordinated approach can be used to extend modeling capabilities by promoting model composability. As part of future work, a framework is envisioned to realize a more coherent strategy for model development and deployment.

Sign in / Sign up

Export Citation Format

Share Document