Influential Parameters to the Database Performance — A Study by Means of Design of Experiments (DoE)

Correction: "Stochastic interpolation of rainfall data from rain gages and radar using Corkriging 1. Design of experiments"

Water Resources Research ◽

10.1029/90wr00788 ◽

1990 ◽

Vol 26 (5) ◽

pp. 1111-1111

Author(s):

Dong-Jun Seo ◽

Witold F. Krajewski ◽

David S. Bowles

Keyword(s):

Design Of Experiments ◽

Rainfall Data ◽

Stochastic Interpolation

Download Full-text

Projektowanie dla jakości metodami Shainina i Taguchiego

Przegląd Organizacji ◽

10.33141/po.2008.01.09 ◽

2008 ◽

pp. 36-38

Author(s):

Jarosław Sęp ◽

Andrzej Pacana

Keyword(s):

Design Of Experiments

Zespół metod wykorzystywanych do planowania eksperymentów określa się jako Design of Experiments -DOE. Celem stosowania DOE jest uzyskanie jak największej ilości wartościowych i wiarygodnych informacji o badanym wyrobie lub procesie na podstawie jak najmniejszej liczby doświadczeń. W artykule zwrócono uwagę na stosunkowo mało znane metody opracowane przez Shainina oraz Taguchiego. Przedstawiono dobór parametrów metodą Shainina i Taguchiego na przykładzie procesu toczenia.

Download Full-text

Performance study of RTV-2 Silicone Rubber Material For Soft Actuator by Experimental and Numerical methods: The Effect of Inflation Pressure and Wall Thickness

International Journal of Automotive and Mechanical Engineering ◽

10.15282/ijame.17.1.2020.01.0556 ◽

2020 ◽

Vol 17 (1) ◽

pp. 7524-7532 ◽

Cited By ~ 1

Author(s):

Deepak D. ◽

Nitesh Kumar ◽

Shreyas P. Shetty ◽

Saurabh Jain ◽

Manoj Bhat

Keyword(s):

Numerical Methods ◽

Wall Thickness ◽

Silicone Rubber ◽

Inflation Pressure ◽

Performance Study ◽

Rubber Material ◽

Soft Actuator ◽

Alternative Materials ◽

Load Carrying ◽

Influential Parameters

The expensive nature of currently used materials in the soft robotic industry demands the consideration of alternative materials for fabrication. This work investigates the performance of RTV-2 grade silicone rubber for fabrication of a soft actuator. Initially, a cylindrical actuator is fabricated using this material and its performance is experimentally assessed for different pressures. Further, parametric variations of the effect of wall thickness and inflation pressure are studied by numerical methods. Results show that, both wall thickness and inflation pressure are influential parameters which affect the elongation behaviour of the actuator. Thin (1.5 mm) sectioned actuators produced 76.97% more elongation compared to thick sectioned, but the stress induced is 89.61 % higher. Whereas, the thick sectioned actuator (6 mm) showed a higher load transmitting capability. With change in wall thickness from 1.5 mm to 6 mm, the elongation is reduced by 76.97 %, 38.35 %, 21.05 % and 11.43 % at pressure 100 kPa, 75 kPa, 50 kPa and 25 kPa respectively. The induced stress is also found reduced by 89.61 %, 86.66 %, 84.46 % and 68.68 % at these pressures. The average load carrying capacity of the actuator is found to be directly proportional to its wall thickness and inflation pressure.

Download Full-text

A THEORETICAL ITERATION FOR PREDICTING THE FEASIBILITY FOR IMMEDIATE FUNCTIONAL DENTAL IMPLANT LOADING

Journal of Oral Implantology ◽

10.1563/aaid-joi-d-20-00194 ◽

2020 ◽

Author(s):

Dennis Flanagan ◽

Alessandro Fisher BS ◽

Carmen Ciardiello ◽

Vito Moreno ◽

Alen Uvalic ◽

...

Keyword(s):

Bone Density ◽

Dental Implant ◽

Cortical Thickness ◽

Load Capacity ◽

Functional Load ◽

Implant Crown ◽

Technical Issues ◽

Implant Loading ◽

Influential Parameters ◽

Functional Loading

When planning an implant supported restoration the dentist is faced with the surgical and prosthetic technical issues as well as the patient’s expectations. Many patients wish an immediate solution to an edentulous condition. This is especially may be true in the esthetic zone. The extent of the zone is determined by the patient. The dentist may consider when it is feasible to load the supporting implants with definitive or provisional prosthetics. For the work herein, consideration of many parameters were theoretically assessed for inclusion: bone density, cortical thickness, seating torque, parafunction, bite load capacity, number of implants under load, implant/crown ratio, implant diameter and length. After assessment, the most influential parameters were selected. An iteration, using patient age, implant diameter, bite load capacity and cortical thickness, is now presented to aid the implant dentist in determining the feasibility for immediate functional loading of a just placed dental implant in a healed site. Extensive testing is required to develop this concept. According to this iteration, most immediate functional loaded implants would fail. A future refined and definitive formula may enable the clinician to safely immediately functional load an implant with a definitive prosthesis.

Download Full-text