scholarly journals Effect of Flow Rate and Viscosity on Complex Fracture Development in UFM Model

10.5772/56406 ◽  
2013 ◽  
Author(s):  
Olga Kresse ◽  
Xiaowei Weng ◽  
Dimitry Chuprakov ◽  
Romain Prioul ◽  
Charles Cohe
Keyword(s):  
Flow Rate ◽  
Complex Fracture ◽  
Fracture Development

Numerical Simulation of Complex Fracture Network Development by Hydraulic Fracturing in Naturally Fractured Ultratight Formations

2013 ◽  
Author(s):  
Hannes Hofmann ◽  
Tayfun Babadagli ◽  
Günter Zimmermann
Keyword(s):  
Fracture Network ◽  
Natural Fracture ◽  
Fracture Networks ◽  
Network Development ◽  
Complex Fracture ◽  
Fracture Patterns ◽  
Fracture Systems ◽  
Fracture Development ◽  
Complex Fracture Network ◽  
Treatment Designs

The creation of large complex fracture networks by hydraulic fracturing is imperative for enhanced oil recovery from tight sand or shale reservoirs, tight gas extraction, and Hot-Dry-Rock (HDR) geothermal systems to improve the contact area to the rock matrix. Although conventional fracturing treatments may result in bi-wing fractures, there is evidence by microseismic mapping that fracture networks can develop in many unconventional reservoirs, especially when natural fracture systems are present and the differences between the principle stresses are low. However, not much insight is gained about fracture development as well as fluid and proppant transport in naturally fractured tight formations. In order to clarify the relationship between rock and treatment parameters, and resulting fracture properties, numerical simulations were performed using a commercial Discrete Fracture Network (DFN) simulator. A comprehensive sensitivity analysis is presented to identify typical fracture network patterns resulting from massive water fracturing treatments in different geological conditions. It is shown how the treatment parameters influence the fracture development and what type of fracture patterns may result from different treatment designs. The focus of this study is on complex fracture network development in different natural fracture systems. Additionally, the applicability of the DFN simulator for modeling shale gas stimulation and HDR stimulation is critically discussed. The approach stated above gives an insight into the relationships between rock properties (specifically matrix properties and characteristics of natural fracture systems) and the properties of developed fracture networks. Various simulated scenarios show typical conditions under which different complex fracture patterns can develop and prescribe efficient treatment designs to generate these fracture systems. Hydraulic stimulation is essential for the production of oil, gas, or heat from ultratight formations like shales and basement rocks (mainly granite). If natural fracture systems are present, the fracturing process becomes more complex to simulate. Our simulation results reveal valuable information about main parameters influencing fracture network properties, major factors leading to complex fracture network development, and differences between HDR and shale gas/oil shale stimulations.

Numerical Investigation of Complex Hydraulic Fracture Development in Naturally Fractured Reservoirs

2015 ◽  
Author(s):  
Wu Kan ◽  
Jon E. Olson
Keyword(s):  
Fracture Propagation ◽  
Injection Pressure ◽  
Natural Fracture ◽  
Hydraulic Fractures ◽  
Differential Stress ◽  
Complex Fracture ◽  
Fracture Patterns ◽  
Fracture Development ◽  
Fracture Complexity ◽  
Shale Reservoirs

Abstract Complex fracture networks have become more evident in shale reservoirs due to the interaction between pre-existing natural and hydraulic fractures. Accurate characterization of fracture complexity plays an important role in optimizing fracturing design, especially for shale reservoirs with high-density natural fractures. In this study, we simulated simultaneous multiple fracture propagation within a single fracturing stage using a complex hydraulic fracture development model. The model was developed to simulate complex fracture propagation by coupling rock mechanics and fluid mechanics. A simplified three-dimensional displacement discontinuity method was implemented to more accurately calculate fracture displacements and fracture-induced dynamic stress changes than our previously developed pseudo-3d model. The effects of perforation cluster spacing, differential stress (SHmax - Shmin) and various geometry natural fracture patterns on injection pressure and fracture complexity were investigated. The single stage simulation results shown that (1) higher differential stress suppresses fracture length and increases injection pressure; (2) there is an optimal choice for the number of fractures per stage to maximize effective fracture surface area, beyond which increasing the number of fractures actually decreases effective fracture area; and (3) fracture complexity is a function of natural fracture patterns (various regular pattern geometries were investigated). Natural fractures with small relative angle to hydraulic fractures are more likely to control fracture propagation path. Also, natural fracture patterns with more long fractures tend to increase the likelihood to dominate the preferential fracture trend of fracture trajectory. Our numerical model can provide a physics-based complex fracture network that can be imported into reservoir simulation models for production analysis. The overall sensitivity results presented should serve as guidelines for fracture complexity analysis.

Numerical Simulation of Complex Fracture Network Development by Hydraulic Fracturing in Naturally Fractured Ultratight Formations

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
Hannes Hofmann ◽  
Tayfun Babadagli ◽  
Günter Zimmermann
Keyword(s):  
Fracture Network ◽  
Natural Fracture ◽  
Fracture Networks ◽  
Network Development ◽  
Complex Fracture ◽  
Fracture Patterns ◽  
Fracture Systems ◽  
Fracture Development ◽  
Complex Fracture Network ◽  
Treatment Designs

The creation of large complex fracture networks by hydraulic fracturing is imperative for enhanced oil recovery from tight sand or shale reservoirs, tight gas extraction, and hot-dry-rock (HDR) geothermal systems to improve the contact area to the rock matrix. Although conventional fracturing treatments may result in biwing fractures, there is evidence by microseismic mapping that fracture networks can develop in many unconventional reservoirs, especially when natural fracture systems are present and the differences between the principle stresses are low. However, not much insight is gained about fracture development as well as fluid and proppant transport in naturally fractured tight formations. In order to clarify the relationship between rock and treatment parameters, and resulting fracture properties, numerical simulations were performed using a commercial discrete fracture network (DFN) simulator. A comprehensive sensitivity analysis is presented to identify typical fracture network patterns resulting from massive water fracturing treatments in different geological conditions. It is shown how the treatment parameters influence the fracture development and what type of fracture patterns may result from different treatment designs. The focus of this study is on complex fracture network development in different natural fracture systems. Additionally, the applicability of the DFN simulator for modeling shale gas stimulation and HDR stimulation is critically discussed. The approach stated above gives an insight into the relationships between rock properties (specifically matrix properties and characteristics of natural fracture systems) and the properties of developed fracture networks. Various simulated scenarios show typical conditions under which different complex fracture patterns can develop and prescribe efficient treatment designs to generate these fracture systems. Hydraulic stimulation is essential for the production of oil, gas, or heat from ultratight formations like shales and basement rocks (mainly granite). If natural fracture systems are present, the fracturing process becomes more complex to simulate. Our simulations suggest that stress state, in situ fracture networks, and fluid type are the main parameters influencing hydraulic fracture network development. Major factors leading to more complex fracture networks are an extensive pre-existing natural fracture network, small fracture spacings, low differences between the principle stresses, well contained formations, high tensile strength, high Young’s modulus, low viscosity fracturing fluid, and large fluid volumes. The differences between 5 km deep granitic HDR and 2.5 km deep shale gas stimulations are the following: (1) the reservoir temperature in granites is higher, (2) the pressures and stresses in granites are higher, (3) surface treatment pressures in granites are higher, (4) the fluid leak-off in granites is less, and (5) the mechanical parameters tensile strength and Young’s modulus of granites are usually higher than those of shales.

Characterize Fracture Development Through Strain Rate Measurements by Distributed Acoustic Sensor DAS

2022 ◽  
Author(s):  
Jin Tang ◽  
Ding Zhu
Keyword(s):  
Hydraulic Fracturing ◽  
Strain Rate ◽  
Fiber Optic ◽  
Fracture Propagation ◽  
Acoustic Sensor ◽  
Observation Well ◽  
Complex Fracture ◽  
Multistage Hydraulic Fracturing ◽  
Fracture Development ◽  
Fracture Growth

Abstract In multistage hydraulic fracturing treatments, the combination of extreme large-scale pumping (high rate and volume) and the high heterogeneity of the formation (because of large contact area) normally results in complex fracture growth that cannot be simply modeled with conventional fracture models. Lack of understanding of the fracturing mechanism makes it difficult to design and optimize hydraulic fracturing treatments. Many monitoring, testing and diagnosis technologies have been applied in the field to describe hydraulic fracture development. Strain rate measured by distributed acoustic sensor (DAS) is one of the tools for fracture monitoring in complex completion scenarios. DAS measures far-field strain rate that can be of assistance for fracture characterization, cross-well fracture interference identification, and well stimulation efficiency evaluation. Many field applications have shown DAS responses on observation wells or surrounding producers when a well in the vicinity is fractured. Modeling and interpreting DAS strain rate responses can help quantitatively map fracture propagation. In this work, a methodology is developed to generate the simulated strain-rate responds to assumed fracture systems. The physical domain contains a treated well that the generate strain variation in the domain because of fracturing, and an observation well that has fiber-optic sensor installed along it to measure the strain rate responses to the fracture propagation. Instead of using a complex fracture model to forward simulate fracture propagation, this work starts from a simple 2D fracture propagation model to provide hypothetical fracture geometries in a relatively reasonable and acceptable range for both single fracture case and multiple fracture case. Displacement discontinuity method (DDM) is formulated to simulate rock deformation and strain rate responds on fiber-optic sensors. At each time step, fracture propagation is first allowed, then stress, displacement and strain field are estimated as the fracture approaches to the observation well. Afterward, the strain rate is calculated as fracture growth to generate patterns as fracture approaching. Extended simulation is conducted to monitor fracture propagation and strain rate responses. The patterns of strain rate responses can be used to recognize fracture development. Examples of strain rate responses for different fracturing conditions are presented in this paper. The relationship of injection rate distribution and strain rate responses is investigated to show the potential of using DAS measurements to diagnose multistage hydraulic fracturing treatments.

A Novel Reconstitution Method for Inducing the Formation of Regular 2-Dimensional Arrays of Membrane Proteins and Lipids

1988 ◽  
Vol 46 ◽  
pp. 152-153 ◽  
Author(s):  
A. Engel ◽  
A. Holzenburg ◽  
K. Stauffer ◽  
J. Rosenbusch ◽  
U. Aebi
Keyword(s):  
Membrane Proteins ◽  
Flow Rate ◽  
Lipid Membranes ◽  
Functional Characterization ◽  
Dimensional Structure ◽  
Electron Crystallography ◽  
Peltier Element ◽  
Protein Ratio ◽  
Precise Control ◽  
3 Dimensional

Reconstitution of solubilized and purified membrane proteins in the presence of phospholipids into vesicles allows their functions to be studied by simple bulk measurements (e.g. diffusion of differently sized solutes) or by conductance measurements after transformation into planar membranes. On the other hand, reconstitution into regular protein-lipid arrays, usually forming at a specific lipid-to-protein ratio, provides the basis for determining the 3-dimensional structure of membrane proteins employing the tools of electron crystallography.To refine reconstitution conditions for reproducibly inducing formation of large and highly ordered protein-lipid membranes that are suitable for both electron crystallography and patch clamping experiments aimed at their functional characterization, we built a flow-dialysis device that allows precise control of temperature and flow-rate (Fig. 1). The flow rate is generated by a peristaltic pump and can be adjusted from 1 to 500 ml/h. The dialysis buffer is brought to a preselected temperature during its travel through a meandering path before it enters the dialysis reservoir. A Z-80 based computer controls a Peltier element allowing the temperature profile to be programmed as function of time.

Novel epoxy/anhydride alternatives for biological electron microscopy: Physical and performance characteristis of embed 812 and LX 112 in combination with NSA/NMA/DMAE

1989 ◽  
Vol 47 ◽  
pp. 1000-1001
Author(s):  
Joe A. Mascorro ◽  
Gerald S. Kirby
Keyword(s):  
Electron Microscopy ◽  
Flow Rate ◽  
Succinic Anhydride ◽  
Volume Flow Rate ◽  
Mass Density ◽  
Uranyl Acetate ◽  
Volume Flow ◽  
Base Resin ◽  
And Performance ◽  
Acid Anhydrides

Embedding media based upon an epoxy resin of choice and the acid anhydrides dodecenyl succinic anhydride (DDSA), nadic methyl anhydride (NMA), and catalyzed by the tertiary amine 2,4,6-Tri(dimethylaminomethyl) phenol (DMP-30) are widely used in biological electron microscopy. These media possess a viscosity character that can impair tissue infiltration, particularly if original Epon 812 is utilized as the base resin. Other resins that are considerably less viscous than Epon 812 now are available as replacements. Likewise, nonenyl succinic anhydride (NSA) and dimethylaminoethanol (DMAE) are more fluid than their counterparts DDSA and DMP- 30 commonly used in earlier formulations. This work utilizes novel epoxy and anhydride combinations in order to produce embedding media with desirable flow rate and viscosity parameters that, in turn, would allow the medium to optimally infiltrate tissues. Specifically, embeding media based on EmBed 812 or LX 112 with NSA (in place of DDSA) and DMAE (replacing DMP-30), with NMA remaining constant, are formulated and offered as alternatives for routine biological work.Individual epoxy resins (Table I) or complete embedding media (Tables II-III) were tested for flow rate and viscosity. The novel media were further examined for their ability to infilftrate tissues, polymerize, sectioning and staining character, as well as strength and stability to the electron beam and column vacuum. For physical comparisons, a volume (9 ml) of either resin or media was aspirated into a capillary viscocimeter oriented vertically. The material was then allowed to flow out freely under the influence of gravity and the flow time necessary for the volume to exit was recored (Col B,C; Tables). In addition, the volume flow rate (ml flowing/second; Col D, Tables) was measured. Viscosity (n) could then be determined by using the Hagen-Poiseville relation for laminar flow, n = c.p/Q, where c = a geometric constant from an instrument calibration with water, p = mass density, and Q = volume flow rate. Mass weight and density of the materials were determined as well (Col F,G; Tables). Infiltration schedules utilized were short (1/2 hr 1:1, 3 hrs full resin), intermediate (1/2 hr 1:1, 6 hrs full resin) , or long (1/2 hr 1:1, 6 hrs full resin) in total time. Polymerization schedules ranging from 15 hrs (overnight) through 24, 36, or 48 hrs were tested. Sections demonstrating gold interference colors were collected on unsupported 200- 300 mesh grids and stained sequentially with uranyl acetate and lead citrate.

Severe Drooling and Treatment With Botulinum Toxin

2012 ◽  
Vol 21 (1) ◽  
pp. 15-21
Author(s):  
Merete Bakke ◽  
Allan Bardow ◽  
Eigild Møller
Keyword(s):  
Botulinum Toxin ◽  
Side Effects ◽  
Health Risk ◽  
Flow Rate ◽  
Clinical Evidence ◽  
Acetylcholine Release ◽  
Psychosocial Problems ◽  
Rate Reduction ◽  
Local Inhibition ◽  
Surgical Treatments

Severe drooling is associated with discomfort and psychosocial problems and may constitute a health risk. A variety of different surgical and non-surgical treatments have been used to diminish drooling, some of them with little or uncertain effect and others more effective but irreversible or with side effects. Based on clinical evidence, injection with botulinum toxin (BTX) into the parotid and submandibular glands is a useful treatment option, because it is local, reversible, and with few side effects, although it has to be repeated. The mechanism of BTX is a local inhibition of acetylcholine release, which diminishes receptor-coupled secretion and results in a flow rate reduction of 25–50% for 2–7 months.

EFFECT OF BODY MASS INDEX ON PEAK EXPIRATORY FLOW RATE

2019 ◽  
Vol 3 (9) ◽  
Author(s):  
K. Subramanyam ◽  
Dr. P. Subhash Babu
Keyword(s):  
Body Mass Index ◽  
Body Mass ◽  
Peak Expiratory Flow ◽  
Flow Rate ◽  
Peak Expiratory Flow Rate ◽  
Normal Weight ◽  
The Body ◽  
Health Care Centre ◽  
Expiratory Flow ◽  
Group B

Obesity has become one of the major health issues in India. WHO defines obesity as “A condition with excessive fat accumulation in the body to the extent that the health and wellbeing are adversely affected”. Obesity results from a complex interaction of genetic, behavioral, environmental and socioeconomic factors causing an imbalance in energy production and expenditure. Peak expiratory flow rate is the maximum rate of airflow that can be generated during forced expiratory manoeuvre starting from total lung capacity. The simplicity of the method is its main advantage. It is measured by using a standard Wright Peak Flow Meter or mini Wright Meter. The aim of the study is to see the effect of body mass index on Peak Expiratory Flow Rate values in young adults. The place of a study was done tertiary health care centre, in India for the period of 6 months. Study was performed on 80 subjects age group 20 -30 years, categorised as normal weight BMI =18.5 -24.99 kg/m2 and overweight BMI =25-29.99 kg/m2. There were 40 normal weight BMI (Group A) and 40 over weight BMI (Group B). BMI affects PEFR. Increase in BMI decreases PEFR. Early identification of risk individuals prior to the onset of disease is imperative in our developing country. Keywords: BMI, PEFR.

SCIENTIFIC AND ENGINEERING PRINCIPLES OF EFFICIENT FUEL USE AND ENVIRONMENTALLY FRIENDLY GAS COMBUSTION IN STOVE PLATES. PART 1. MODERN STATE-OF-THE-ART AND DIRECTIONS FOR IMPROVEMENT THE GAS BURNING IN DOMESTIC GAS COOKERS

2017 ◽  
pp. 3-18 ◽  
Author(s):  
B.S. Soroka ◽  
V.V. Horupa
Keyword(s):  
Natural Gas ◽  
Flow Rate ◽  
Gas Flow ◽  
Renewable Energy Sources ◽  
Combustion Process ◽  
Orifice Diameter ◽  
Firing Process ◽  
Gas Flow Rate ◽  
Gas Combustion ◽  
Gas Stoves

Natural gas NG consumption in industry and energy of Ukraine, in recent years falls down as a result of the crisis in the country’s economy, to a certain extent due to the introduction of renewable energy sources along with alternative technologies, while in the utility sector the consumption of fuel gas flow rate enhancing because of an increase the number of consumers. The natural gas is mostly using by domestic purpose for heating of premises and for cooking. These items of the gas utilization in Ukraine are already exceeding the NG consumption in industry. Cooking is proceeding directly in the living quarters, those usually do not meet the requirements of the Ukrainian norms DBN for the ventilation procedures. NG use in household gas stoves is of great importance from the standpoint of controlling the emissions of harmful components of combustion products along with maintenance the satisfactory energy efficiency characteristics of NG using. The main environment pollutants when burning the natural gas in gas stoves are including the nitrogen oxides NOx (to a greater extent — highly toxic NO2 component), carbon oxide CO, formaldehyde CH2O as well as hydrocarbons (unburned UHC and polyaromatic PAH). An overview of environmental documents to control CO and NOx emissions in comparison with the proper norms by USA, EU, Russian Federation, Australia and China, has been completed. The modern designs of the burners for gas stoves are considered along with defining the main characteristics: heat power, the natural gas flow rate, diameter of gas orifice, diameter and spacing the firing openings and other parameters. The modern physical and chemical principles of gas combustion by means of atmospheric ejection burners of gas cookers have been analyzed from the standpoints of combustion process stabilization and of ensuring the stability of flares. Among the factors of the firing process destabilization within the framework of analysis above mentioned, the following forms of unstable combustion/flame unstabilities have been considered: flashback, blow out or flame lifting, and the appearance of flame yellow tips. Bibl. 37, Fig. 11, Tab. 7.

Sign in / Sign up

Export Citation Format

Share Document