scholarly journals Investigation of the Structure and Properties of PVD and PACVD-Coated Magnesium Die Cast Alloys

10.5772/48165 ◽  
2012 ◽  
Author(s):  
Tomasz Taski
Keyword(s):  
Structure And Properties ◽  
Die Cast ◽  
Cast Alloys

Microstructure of die-cast alloys Mg–Zn–Al(–Ca): a study by electron microscopy and small-angle neutron scattering

2003 ◽  
Vol 94 (5) ◽  
pp. 564-571 ◽  
Author(s):  
Michael Vogel ◽  
Oliver Kraft ◽  
Peter Staron ◽  
Helmut Clemens ◽  
Rainer Rauh ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Neutron Scattering ◽  
Small Angle ◽  
Small Angle Neutron Scattering ◽  
Die Cast ◽  
Cast Alloys

Influence of Sr and TiB on the Microstructure and Eutectic Temperature of Al-12Si Die-Cast Alloys

2017 ◽  
Vol 27 (10) ◽  
pp. 544-551
Author(s):  
Yong-Lak Choi ◽  
◽  
Seon-Hwa Kim ◽  
Dong-Hyun Kim ◽  
Sang-Il Yoon ◽  
...  
Keyword(s):  
Eutectic Temperature ◽  
Die Cast ◽  
Cast Alloys

scholarly journals The development of low-temperature heat-treatable high-pressure die-cast Al–Mg–Fe–Mn alloys with Zn

2021 ◽  
Author(s):  
Xiangzhen Zhu ◽  
Fuchu Liu ◽  
Shihao Wang ◽  
Shouxun Ji
Keyword(s):  
Heat Treatment ◽  
Low Temperature ◽  
Mechanical Test ◽  
Equilibrium Phase ◽  
Solution Temperature ◽  
Tem Analysis ◽  
Die Cast ◽  
Zn Concentration ◽  
Temperature Heat ◽  
Cast Alloys

AbstractIn the present work, a novel low-temperature heat-treatable recycled die-cast Al–Mg alloy was developed by adding Zn into non-heat-treatable Al–5Mg–1.5Fe–0.5Mn alloy. The results showed that Zn additions resulted in the formation of equilibrium phase T-Mg32(Al, Zn)49 under as-cast condition, which can be dissolved into the α-Al matrix at a relatively low solution temperature (430 °C) and thus set the base for the low-temperature heat treatment. The mechanical test results indicated that Zn additions had a smooth liner improvement in the strength of all as-cast alloys and T6-state alloys with 1% and 2% Zn as its concentration increased but resulted in a sharp improvement on the strength of T6-state alloy when Zn concentration increased from 2 to 3%. TEM analysis revealed that the precipitate in T6-state Al–5Mg–1.5Fe–0.5Mn–3Zn alloy is η′ phase, rather than the widely reported T″ or T′ phase in other Al–Mg–Zn alloys with approximately same Mg and Zn concentrations. After the optimized low-temperature T6 heat treatment (solution at 430 °C for 60 min and ageing at 120 °C for 16 h), the Al–5Mg–1.5Fe–0.5Mn–3Zn alloy exhibits the yield strength of 321 MPa, ultimate tensile strength of 445 MPa and elongation of 6.2%.

Phase Transformation and Creep of Mg-Al-Ca Based Die-Cast Alloys

2014 ◽  
pp. 291-296
Author(s):  
Akane Suzuki ◽  
Nicholas D. Saddock ◽  
J. Wayne Jones ◽  
Tresa M. Pollock
Keyword(s):  
Phase Transformation ◽  
Die Cast ◽  
Cast Alloys

Evaluation of Young's modulus of high stiffness aluminium die cast alloys using nanoindentation technique

2008 ◽  
Vol 21 (1-4) ◽  
pp. 180-185
Author(s):  
M. Yabushita ◽  
T. Goda ◽  
Y. Ono ◽  
H. Tezuka ◽  
T. Sato ◽  
...  
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
High Stiffness ◽  
Nanoindentation Technique ◽  
Die Cast ◽  
Cast Alloys

Effect of alloying elements on the structure and properties of Al-Li-Cu cast alloys

2009 ◽  
Vol 2009 (4) ◽  
pp. 338-344 ◽  
Author(s):  
A. A. Il’in ◽  
S. L. Nikitin ◽  
O. E. Osintsev ◽  
Yu. V. Borisov
Keyword(s):  
Alloying Elements ◽  
Structure And Properties ◽  
Cast Alloys ◽  
Effect Of Alloying

Structure and Properties of New Heat-Resistant Cast Alloys Based on the Al–Cu–Y and Al–Cu–Er Systems

2021 ◽  
Vol 122 (9) ◽  
pp. 908-914
Author(s):  
S. M. Amer ◽  
R. Yu. Barkov ◽  
A. S. Prosviryakov ◽  
A. V. Pozdniakov
Keyword(s):  
Structure And Properties ◽  
Heat Resistant ◽  
Cast Alloys

Phase Transformation and Creep of Mg-Al-Ca Based Die-Cast Alloys

2016 ◽  
pp. 291-296 ◽  
Author(s):  
Akane Suzuki ◽  
Nicholas D. Saddock ◽  
J. Wayne Jones ◽  
Tresa M. Pollock
Keyword(s):  
Phase Transformation ◽  
Die Cast ◽  
Cast Alloys
Sign in / Sign up

Export Citation Format

Share Document