scholarly journals Application of Infrared Spectroscopy in Biomedical Polymer Materials

10.5772/48060 ◽  
2012 ◽  
Author(s):  
Zhang Li ◽  
Wang Minzhu ◽  
Zhen Jian ◽  
Zhou Ju
Keyword(s):  
Infrared Spectroscopy ◽  
Polymer Materials ◽  
Biomedical Polymer

Investigation into the Differences Chemical Properties of Laser Sintering Polymer Powders Using Fourier Transform Infrared Spectroscopy

2014 ◽  
Vol 548-549 ◽  
pp. 133-136
Author(s):  
Yusoff Way ◽  
Hadi Puwanto ◽  
Farizahani ◽  
P.T. Pham
Keyword(s):  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Chemical Composition ◽  
Fourier Transform Infrared Spectroscopy ◽  
Surface Finish ◽  
Chemical Properties ◽  
Fourier Transform Infrared ◽  
Laser Sintering ◽  
Polymer Materials ◽  
Powder Materials

Selective Laser Sintering (SLS) or Laser Sintering (LS) allows functional parts to be produced in a wide range of powdered materials using a dedicated machine, and is thus gaining popularity within the field of Rapid Prototyping (RP). One of the advantages of employing LS is that the loose powder of the building chamber can be recycled. The properties of polymer powder significantly influence the melt viscosity and sintering mechanism during Laser Sintering (LS) processes which results in a good surface finish. The objective of this research is to investigate the chemical composition of fresh polymer materials used in Laser Sintering. There are seven virgin SLS materials which are PA2200, GF3200, Alumide, PrimeCast, PrimePart, Duraflex and CastForm. Fourier Transform Infrared Spectroscopy (FTIR) was used to analyze the chemical composition of the materials by using infrared radiation and absorbed frequency. The spectra show that similar functional groups were found in the materials apart from PrimePart and Duraflex. Obtained data from this analysis could be used to investigate on how the fresh and recycled powder materials with different chemical properties would affect the part surface finish.

Comparison of the dose perturbation arising from conventional and the novel PEEK prosthesis materials during high energy radiotherapy with 15 MV photons

2021 ◽  
pp. 1-7
Author(s):  
Najmeh Mohammadi
Keyword(s):  
High Energy ◽  
Polymer Materials ◽  
Hip Prostheses ◽  
Metal Implants ◽  
Depth Dose ◽  
Before And After ◽  
New Material ◽  
Biomedical Polymer ◽  
Dose Perturbation ◽  
The Impact

Abstract Aim: This study aimed to evaluate the dosimetric effects of the metal prosthesis in radiotherapy by Siemens Primus 15 MV linac accelerator. In addition, it proposed the new material could lead to less dose perturbation. Materials and methods: The depth dose distributions of typical hip prostheses were calculated for 15 MV photons by MCNP-4C code. Five metal prostheses were selected to reveal the correlation between material type, density and dose perturbations of prostheses. Furthermore, the effects of the location and thickness of the prosthesis on the dose perturbation were also discussed and analysed. Results: The results showed that the Co-Cr-Mo alloy as the prosthesis had more influence on the dose at the interface of metal tissue. The dose increased at the entrance of this prosthesis and experienced the reduction when passed through it. Finally, the impact of the new PEEK biomedical polymer materials was also investigated, and the lowest dose perturbations were introduced based on the obtained results. Conclusion: It was found that the mean relative dose before and after of PEEK prosthesis was 99·2 and 97·1%, respectively. Therefore, this new biomedical polymer material was proposed to replace the current metal implants.

Electrical-thermal aging characteristic research of polymer materials by infrared spectroscopy,

2014 ◽  
Vol 25 (12) ◽  
pp. 1396-1405 ◽  
Author(s):  
Wei Wang ◽  
Dongxin He ◽  
Jiefeng Gu ◽  
Jian Lu ◽  
Jiazhen Du
Keyword(s):  
Infrared Spectroscopy ◽  
Thermal Aging ◽  
Polymer Materials ◽  
Aging Characteristic

Electron-diffraction studies in synthetic polymer materials

1983 ◽  
Vol 41 ◽  
pp. 362-365
Author(s):  
D.T. Grubb
Keyword(s):  
Electron Diffraction ◽  
Synthetic Polymer ◽  
Polymer Materials ◽  
Crystallographic Structure ◽  
High Dose ◽  
Electron Dose ◽  
Dose Rates ◽  
First Case ◽  
Diffraction Patterns ◽  
The Many

Diffraction studies in polymeric and other beam sensitive materials may bring to mind the many experiments where diffracted intensity has been used as a measure of the electron dose required to destroy fine structure in the TEM. But this paper is concerned with a range of cases where the diffraction pattern itself contains the important information.In the first case, electron diffraction from paraffins, degraded polyethylene and polyethylene single crystals, all the samples are highly ordered, and their crystallographic structure is well known. The diffraction patterns fade on irradiation and may also change considerably in a-spacing, increasing the unit cell volume on irradiation. The effect is large and continuous far C94H190 paraffin and for PE, while for shorter chains to C 28H58 the change is less, levelling off at high dose, Fig.l. It is also found that the change in a-spacing increases at higher dose rates and at higher irradiation temperatures.

Structure-property relationships of PE/PP sandwiched films

1987 ◽  
Vol 45 ◽  
pp. 454-455
Author(s):  
J. Petermann ◽  
G. Broza ◽  
U. Rieck ◽  
A. Jaballah ◽  
A. Kawaguchi
Keyword(s):  
Mechanical Tests ◽  
Polymer Materials ◽  
Ionic Crystals ◽  
Structure Property ◽  
Polymer Systems ◽  
Structure Property Relationships ◽  
Oriented Films ◽  
Materials Used ◽  
Polymer Laminates ◽  
Heated Glass

Oriented overgrowth of polymer materials onto ionic crystals is well known and recently it was demonstrated that this epitaxial crystallisation can also occur in polymer/polymer systems, under certain conditions. The morphologies and the resulting physical properties of such systems will be presented, especially the influence of epitaxial interfaces on the adhesion of polymer laminates and the mechanical properties of epitaxially crystallized sandwiched layers.Materials used were polyethylene, PE, Lupolen 6021 DX (HDPE) and 1810 D (LDPE) from BASF AG; polypropylene, PP, (PPN) provided by Höchst AG and polybutene-1, PB-1, Vestolen BT from Chemische Werke Hüls. Thin oriented films were prepared according to the method of Petermann and Gohil, by winding up two different polymer films from two separately heated glass-plates simultaneously with the help of a motor driven cylinder. One double layer was used for TEM investigations, while about 1000 sandwiched layers were taken for mechanical tests.

Sign in / Sign up

Export Citation Format

Share Document