scholarly journals Experimental Study on Generation of Single Cavitation Bubble Collapse Behavior by a High Speed Camera Record

10.5772/38489 ◽  
2012 ◽  
Author(s):  
Sheng-Hsueh Yang ◽  
Shenq-Yuh Jaw ◽  
Keh-Chia Yeh
Keyword(s):  
Experimental Study ◽  
Cavitation Bubble ◽  
High Speed ◽  
Bubble Collapse ◽  
High Speed Camera ◽  
Collapse Behavior

Cavitation erosion behavior of hydraulic concrete under high-speed flow

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Xin Wang ◽  
Ting-Qiang Xie
Keyword(s):  
Cavitation Bubble ◽  
High Speed ◽  
Cavitation Erosion ◽  
Concrete Strength ◽  
Bubble Collapse ◽  
High Speed Flow ◽  
Content Type ◽  
Erosion Behavior ◽  
Hydraulic Concrete ◽  
Speed Flow

Purpose Cavitation erosion has always been a common technical problem in a hydraulic discharging structure. This paper aims to investigate the cavitation erosion behavior of hydraulic concrete under high-speed flow. Design/methodology/approach A high-speed and high-pressure venturi cavitation erosion generator was used to simulate the strong cavitation. The characteristics of hydrodynamic loads of cavitation bubble collapse zone, the failure characteristics and the erosion development process of concrete were investigated. The main influencing factors of cavitation erosion were discussed. Findings The collapse of the cavitation bubble group produced a high frequency, continuous and unsteady pulse load on the wall of concrete, which was more likely to cause fatigue failure of concrete materials. The cavitation action position and the main frequency of impact load were greatly affected by the downstream pressure. A power exponential relationship between cavitation load, cavitation erosion and flow speed was observed. With the increase of concrete strength, the degree of damage of cavitation erosion was approximately linearly reduced. Originality/value After cavitation erosion, a skeleton structure was formed by the accumulation of granular particles, and the relatively independent bulk structure of the surface differed from the flake structure formed after abrasion.

scholarly journals A Photographic Study of Spark-Induced Cavitation Bubble Collapse

1972 ◽  
Vol 94 (4) ◽  
pp. 825-832 ◽  
Author(s):  
C. L. Kling ◽  
F. G. Hammitt
Keyword(s):  
Cavitation Bubble ◽  
High Speed ◽  
Bubble Collapse ◽  
Solid Boundary ◽  
High Speed Photography ◽  
Minimum Volume ◽  
Cavitation Bubbles ◽  
Flowing System

The collapse of spark-induced cavitation bubbles in a flowing system was studied by means of high speed photography. The migration of cavitation bubbles toward a nearby solid boundary during collapse and rebound was observed. Near its minimum volume the bubble typically formed a high speed microjet, which struck the nearby surface causing individual damage craters on soft aluminum.

Experimental Study of Kick up Phenomenon in Thermosonic Wire-Bonding

2012 ◽  
Vol 160 ◽  
pp. 77-81
Author(s):  
Jing Jing Tian ◽  
Lei Han
Keyword(s):  
Image Processing ◽  
Experimental Study ◽  
High Speed ◽  
Gold Wire ◽  
Wire Bonding ◽  
Processing Method ◽  
Experimental Results ◽  
High Speed Camera ◽  
Depth Study ◽  
Thermosonic Wire Bonding

Kick-up phenomenon during looping is an important factor in thermosonic wire bonding. In this study, the loping process during wire bonding was recorded by using high-speed camera, and wire profiles evolution was obtained from images sequence by image processing method. With a polynomial fitting, the wire loop profiling was described by the curvature changing, and kick-up phenomenon on gold wire was found between the instant of 290th frame(0.0537s) to 380th frame (0.0703s), the change of curvature is divided into three phases, a looping phase, a mutation phase and a kick-up phase. While in the kick-up phase, the kick up phenomenon is the most obvious. These experimental results were useful for in-depth study of kick-up phenomenon by simulation.

Experimental Study on the Response Characteristics of Oilcans under High-Velocity Fragment Impact

2012 ◽  
Vol 510 ◽  
pp. 500-506
Author(s):  
Chang Hai Chen ◽  
Xi Zhu ◽  
Hai Liang Hou ◽  
Li Jun Zhang ◽  
Ting Tang
Keyword(s):  
Experimental Study ◽  
High Velocity ◽  
High Speed ◽  
Room Temperature ◽  
Experimental Results ◽  
Fuel Oil ◽  
High Speed Camera ◽  
Response Characteristics ◽  
Fuel Oils ◽  
The Impact

To explore the deflagration possibility of the warship cabin filled with fuel oil under impact of high-speed fragments in the condition of room temperature, experiments were carried out employing the small aluminium oilcans filled with fuel oil. Response processes of the oilcans were observed with the help of a high-speed camera. The disintegration as well as flying scattering of the oilcans were analyzed. The reasons for atomization of the fuel oils were presented. Finally, the deflagration possibility of warship oil cabin was analyzed. Results show that the pressure inside the oilcan is quite great under the impact of the high-speed fragment, which makes the oilcan disintegration and flying scattering. Simultaneously, fuel oils inside the oilcans are atomized quickly followed by ejected in front and back directions. Under the same condition as in present tests, deflagration will not occur for fuel oils used by warships. Experimental results will provide valuable references for the deflagration analysis of warship fuel oil cabins subjected to the impact of high-velocity fragments.

Fragmentation of acoustically levitating droplets by laser-induced cavitation bubbles

2016 ◽  
Vol 805 ◽  
pp. 551-576 ◽  
Author(s):  
Silvestre Roberto Gonzalez Avila ◽  
Claus-Dieter Ohl
Keyword(s):  
Shock Wave ◽  
Experimental Study ◽  
Surface Tension ◽  
Cavitation Bubble ◽  
High Speed ◽  
Size Range ◽  
Sound Field ◽  
Negative Pressures ◽  
Impulsive Pressure ◽  
Small Bubbles

We report on an experimental study on the dynamics and fragmentation of water droplets levitated in a sound field exposed to a single laser-induced cavitation bubble. The nucleation of the cavitation bubble leads to a shock wave travelling inside the droplet and reflected from pressure release surfaces. Experiments and simulations study the location of the high negative pressures inside the droplet which result into secondary cavitation. Later, three distinct fragmentation scenarios are observed: rapid atomization, sheet formation and coarse fragmentation. Rapid atomization occurs when the expanding bubble, still at high pressure, ruptures the liquid film separating the bubble from the surrounding air and a shock wave is launched into the surrounding air. Sheet formation occurs due to the momentum transfer of the expanding bubble; for sufficiently small bubbles, the sheet retracts because of surface tension, while larger bubbles may cause the fragmentation of the sheet. Coarse fragmentation is observed after the first collapse of the bubble, where high-speed jets emanate from the surface of the droplet. They are the result of surface instability of the droplet combined with the impulsive pressure generated during collapse. A parameter plot for droplets in the size range between 0.17 and 1.5 mm and laser energies between 0.2 and 4.0 mJ allows the separation of these three regimes.

scholarly journals Cavitation and bubble dynamics: the Kelvin impulse and its applications

2015 ◽  
Vol 5 (5) ◽  
pp. 20150017 ◽  
Author(s):  
John R. Blake ◽  
David M. Leppinen ◽  
Qianxi Wang
Keyword(s):  
Cavitation Bubble ◽  
High Speed ◽  
Bubble Dynamics ◽  
Clinical Medicine ◽  
Bubble Collapse ◽  
Rigid Boundary ◽  
Design Problems ◽  
Practical Applications ◽  
Wide Range ◽  
Naval Engineering

Cavitation and bubble dynamics have a wide range of practical applications in a range of disciplines, including hydraulic, mechanical and naval engineering, oil exploration, clinical medicine and sonochemistry. However, this paper focuses on how a fundamental concept, the Kelvin impulse, can provide practical insights into engineering and industrial design problems. The pathway is provided through physical insight, idealized experiments and enhancing the accuracy and interpretation of the computation. In 1966, Benjamin and Ellis made a number of important statements relating to the use of the Kelvin impulse in cavitation and bubble dynamics, one of these being ‘One should always reason in terms of the Kelvin impulse, not in terms of the fluid momentum…’. We revisit part of this paper, developing the Kelvin impulse from first principles, using it, not only as a check on advanced computations (for which it was first used!), but also to provide greater physical insights into cavitation bubble dynamics near boundaries (rigid, potential free surface, two-fluid interface, flexible surface and axisymmetric stagnation point flow) and to provide predictions on different types of bubble collapse behaviour, later compared against experiments. The paper concludes with two recent studies involving (i) the direction of the jet formation in a cavitation bubble close to a rigid boundary in the presence of high-intensity ultrasound propagated parallel to the surface and (ii) the study of a ‘paradigm bubble model’ for the collapse of a translating spherical bubble, sometimes leading to a constant velocity high-speed jet, known as the Longuet-Higgins jet.

Development of a test method and experimental study on cable unwinding

2020 ◽  
pp. 095440622095449
Author(s):  
Ji-Heon Kang ◽  
Kun-Woo Kim ◽  
Jae-Wook Lee ◽  
Yong-Jae Cho ◽  
Jin-Seok Jang
Keyword(s):  
Experimental Study ◽  
Textile Industry ◽  
High Speed ◽  
Translational Motion ◽  
Control Device ◽  
Test Method ◽  
Experimental Device ◽  
High Speed Camera

In addition to the textile industry, unwinding of cable or fiber is used in various fields such as electronics, communication, and guided weapons. The cable released from the package exhibit a complicated behavior, entailing a combination of rotational and translational motion. This causes problems such as entangling and fracture. Therefore, it is necessary to study boundary and adhesion conditions to prevent unwinding failure. In this study, an experimental device for the analysis of cable unwinding was developed, and unwinding behavior was analyzed experimentally under various unwinding conditions. The experimental device comprises a jig for high-speed camera measurements, control device, and cable unwinding device. Cable behavior was analyzed according to the unwinding velocity and the distance between the fiber package and the point where the fiber was released. In addition, unwinding behavior with respect of the tension acting on the cable was analyzed experimentally by applying the adhesive.

Sign in / Sign up

Export Citation Format

Share Document