scholarly journals Power Output Characteristics of Transparent a-Si BiPV Window Module

10.5772/21469 ◽  
2011 ◽  
Author(s):  
Jongho Yoon
Keyword(s):  
Power Output ◽  
Output Characteristics

scholarly journals A Novel Design of Multi-Chambered Biomass Battery

2013 ◽  
Vol 2 (1) ◽  
pp. 31 ◽  
Author(s):  
K. Sudhakar ◽  
R. Ananthakrishnan ◽  
A. Goyal ◽  
H.K. Darji
Keyword(s):  
Power Generation ◽  
Power Output ◽  
Rural Household ◽  
Raw Material ◽  
Cow Dung ◽  
Battery Design ◽  
Output Characteristics ◽  
First Time ◽  
Novel Design

In this paper, a novel design of biomass battery has been introduced for providingelectricity to meet the lighting requirements of rural household using biomass. A biomass battery isdesigned, developed and tested using cow dung as the raw material. This is done via anaerobicdigestion of the cow dung, and power generation driven by the ions produced henceforth. Thevoltage and power output is estimated for the proposed system. It is for the first time that such ahigh voltage is obtained from cow dung fed biomass battery. The output characteristics of thisnovel battery design have also been compared with the previously designed battery.

A Novel Approach to Improving the Available Power Output of Piezoelectric Ultrasonic Motors

2004 ◽  
Author(s):  
R. M. Tieck ◽  
G. P. Carman
Keyword(s):  
Power Output ◽  
Contact Layer ◽  
Friction Forces ◽  
Ultrasonic Motors ◽  
Novel Approach ◽  
Baseline Testing ◽  
Limited Power ◽  
Industrial Use ◽  
Output Characteristics ◽  
Piezoelectric Ultrasonic Motor

Piezoelectric actuators have attractive operating properties because they do not generate electromagnetic fields and are not affected by them, and their power output characteristics scale linearly with decreasing size. These actuators have not seen widespread industrial use, however, because they have shown a limited power output. This work presents the initial efforts to increase the available power output of the Piezoelectric Ultrasonic Motor (PUSM). Commercially available PUSMs are limited by the small friction forces generated at the rotor/stator interface. Small friction is generated because current PUMs use rubber or polyimides on the rotor to create as the contact with the stator. Traditionally, PUSM contact material has consisted of rubber or reinforced polyimides. The authors intend to replace the traditional contact layer with a compliant super-elastic Nickel-Titanium (NiTi) thin film shape memory alloy (SMA) layer to increase the available power output by increasing the friction forces at the rotor/stator interface, without significantly increasing the size or weight of the actuator. The unmodified motors were baselined tested, modified, tested and the results compared. Recommendations are made with regard to the results of the modified baseline testing and possible implementation of micromachined ‘teeth’ configurations.

scholarly journals Analysis of Output Characteristics of Typical Distributed Wind Power

2019 ◽  
Vol 79 ◽  
pp. 03017
Author(s):  
Mingyu Dong ◽  
Dezhi Li ◽  
Fenkai Chen ◽  
Meiyan Wang ◽  
Rongjun Chen ◽  
...  
Keyword(s):  
Wind Power ◽  
Power Output ◽  
Power Distribution ◽  
Large Scale ◽  
Power Grid ◽  
Stable Operation ◽  
Smart Power ◽  
Power Exchange ◽  
The Future ◽  
Output Characteristics

With the development of smart power distribution technology in the future, a large range of power supply load (such as distributed wind power generation) will appear on the power receiving end. When distributed wind power is connected to the power grid on a large scale, it will have a certain impact on the safe and stable operation of the power grid. However, if the wind power output characteristics can be analyzed and the wind power output is properly regulated, the one-way flow of power from the distribution network to the user side will be broken, so that the future "network-load" has dual interaction characteristics based on response and substantial power exchange.

Sign in / Sign up

Export Citation Format

Share Document