scholarly journals Aircraft Gas-Turbine Engine’s Control Based on the Fuel Injection Control

10.5772/17986 ◽  
2011 ◽  
Author(s):  
Alexandru-Nicolae Tudosie
Keyword(s):  
Gas Turbine ◽  
Fuel Injection ◽  
Injection Control

Modeling of Gas Turbine Fuel Nozzle Spray

1997 ◽  
Vol 119 (1) ◽  
pp. 34-44 ◽  
Author(s):  
N. K. Rizk ◽  
J. S. Chin ◽  
M. K. Razdan
Keyword(s):  
Gas Turbine ◽  
Fuel Injection ◽  
Near Field ◽  
Continuous Phase ◽  
Liquid Sheet ◽  
Vapor Concentration ◽  
Fuel Vapor ◽  
Fuel Injector ◽  
Gas Temperature ◽  
Sheet Breakup

Satisfactory performance of the gas turbine combustor relies on the careful design of various components, particularly the fuel injector. It is, therefore, essential to establish a fundamental basis for fuel injection modeling that involves various atomization processes. A two-dimensional fuel injection model has been formulated to simulate the airflow within and downstream of the atomizer and address the formation and breakup of the liquid sheet formed at the atomizer exit. The sheet breakup under the effects of airblast, fuel pressure, or the combined atomization mode of the airassist type is considered in the calculation. The model accounts for secondary breakup of drops and the stochastic Lagrangian treatment of spray. The calculation of spray evaporation addresses both droplet heat-up and steady-state mechanisms, and fuel vapor concentration is based on the partial pressure concept. An enhanced evaporation model has been developed that accounts for multicomponent, finite mass diffusivity and conductivity effects, and addresses near-critical evaporation. The presents investigation involved predictions of flow and spray characteristics of two distinctively different fuel atomizers under both nonreacting and reacting conditions. The predictions of the continuous phase velocity components and the spray mean drop sizes agree well with the detailed measurements obtained for the two atomizers, which indicates the model accounts for key aspects of atomization. The model also provides insight into ligament formation and breakup at the atomizer exit and the initial drop sizes formed in the atomizer near field region where measurements are difficult to obtain. The calculations of the reacting spray show the fuel-rich region occupied most of the spray volume with two-peak radial gas temperature profiles. The results also provided local concentrations of unburned hydrocarbon (UHC) and carbon monoxide (CO) in atomizer flowfield, information that could support the effort to reduce emission levels of gas turbine combustors.

Development and Integration of the Dual Fuel Combustion System for the MGT Gas Turbine Family

2021 ◽  
Author(s):  
Bernhard Ćosić ◽  
Frank Reiss ◽  
Marc Blümer ◽  
Christian Frekers ◽  
Franklin Genin ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Distribution System ◽  
Gas Turbines ◽  
Liquid Fuel ◽  
Fuel Injection ◽  
Liquid Fuels ◽  
Dual Fuel ◽  
Gaseous Fuels ◽  
Supply And Distribution ◽  
Industrial Gas Turbines

Abstract Industrial gas turbines like the MGT6000 are often operated as power supply or as mechanical drives. In these applications, liquid fuels like 'Diesel Fuel No.2' can be used either as main fuel or as backup fuel if natural gas is not reliably available. The MAN Gas Turbines (MGT) operate with the Advanced Can Combustion (ACC) system, which is capable of ultra-low NOx emissions for gaseous fuels. This system has been further developed to provide dry dual fuel capability. In the present paper, we describe the design and detailed experimental validation process of the liquid fuel injection, and its integration into the gas turbine package. A central lance with an integrated two-stage nozzle is employed as a liquid pilot stage, enabling ignition and start-up of the engine on liquid fuel only. The pilot stage is continuously operated, whereas the bulk of the liquid fuel is injected through the premixed combustor stage. The premixed stage comprises a set of four decentralized nozzles based on fluidic oscillator atomizers, wherein atomization of the liquid fuel is achieved through self-induced oscillations. We present results illustrating the spray, hydrodynamic, and emission performance of the injectors. Extensive testing of the burner at atmospheric and full load high-pressure conditions has been performed, before verification within full engine tests. We show the design of the fuel supply and distribution system. Finally, we discuss the integration of the dual fuel system into the standard gas turbine package of the MGT6000.

Low-Emissions Technology Development for Auxiliary Power Unit Combustion Systems

2021 ◽  
Author(s):  
Thomas Bronson ◽  
Rudy Dudebout ◽  
Nagaraja Rudrapatna
Keyword(s):  
Gas Turbine ◽  
Power Unit ◽  
Fuel Injection ◽  
Oxides Of Nitrogen ◽  
Combustion System ◽  
Auxiliary Power Unit ◽  
Criteria Pollutants ◽  
Auxiliary Power ◽  
Combustion Systems ◽  
Aircraft Application

Abstract The aircraft Auxiliary Power Unit (APU) is required to provide power to start the main engines, conditioned air and power when there are no facilities available and, most importantly, emergency power during flight operation. Given the primary purpose of providing backup power, APUs have historically been designed to be extremely reliable while minimizing weight and fabrication cost. Since APUs are operated at airports especially during taxi operations, the emissions from the APUs contribute to local air quality. There is clearly significant regulatory and public interest in reducing emissions from all sources at airports, including from APUs. As such, there is a need to develop technologies that reduce criteria pollutants, namely oxides of nitrogen (NOx), unburned hydrocarbons (UHC), carbon monoxide (CO) and smoke (SN) from aircraft APUs. Honeywell has developed a Low-Emissions (Low-E) combustion system technology for the 131-9 and HGT750 family of APUs to provide significant reduction in pollutants for narrow-body aircraft application. This article focuses on the combustor technology and processes that have been successfully utilized in this endeavor, with an emphasis on abating NOx. This paper describes the 131-9/HGT750 APU, the requirements and challenges for small gas turbine engines, and the selected strategy of Rich-Quench-Lean (RQL) combustion. Analytical and experimental results are presented for the current generation of APU combustion systems as well as the Low-E system. The implementation of RQL aerodynamics is well understood within the aero-gas turbine engine industry, but the application of RQL technology in a configuration with tangential liquid fuel injection which is also required to meet altitude ignition at 41,000 ft is the novelty of this development. The Low-E combustion system has demonstrated more than 25% reduction in NOx (dependent on the cycle of operation) vs. the conventional 131-9 combustion system while meeting significant margins in other criteria pollutants. In addition, the Low-E combustion system achieved these successes as a “drop-in” configuration within the existing envelope, and without significantly impacting combustor/turbine durability, combustor pressure drop, or lean stability.

scholarly journals Compensation of sub-harmonic vibrations during engine idle by variable fuel injection control

2008 ◽  
Vol 41 (2) ◽  
pp. 9459-9466 ◽  
Author(s):  
Andreas Walter ◽  
Mustafa Murt ◽  
Uwe Kiencke ◽  
Stephen Jones ◽  
Thomas Winkler
Keyword(s):  
Fuel Injection ◽  
Harmonic Vibrations ◽  
Injection Control

Model Simulation and Design Optimization of a Can Combustor with Methane/Syngas Fuels for a Micro Gas Turbine

2018 ◽  
Vol 0 (0) ◽  
Author(s):  
Chi-Rong Liu ◽  
Ming-Tsung Sun ◽  
Hsin-Yi Shih
Keyword(s):  
Gas Turbine ◽  
Turbulent Flows ◽  
Film Cooling ◽  
Fuel Injection ◽  
Model Simulation ◽  
Combustion Process ◽  
Three Dimensional ◽  
Future Application ◽  
Detailed Chemical Kinetics ◽  
Micro Gas Turbine

Abstract The design and model simulation of a can combustor has been made for future syngas combustion application in a micro gas turbine. An improved design of the combustor is studied in this work, where a new fuel injection strategy and film cooling are employed. The simulation of the combustor is conducted by a computational model, which consists of three-dimensional, compressible k-ε model for turbulent flows and PPDF (Presumed Probability Density Function) model for combustion process invoking a laminar flamelet assumption generated by detailed chemical kinetics from GRI 3.0. Thermal and prompt NOx mechanisms are adopted to predict the NO formation. The modeling results indicated that the high temperature flames are stabilized in the center of the primary zone by radially injecting the fuel inward. The exit temperatures of the modified can combustor drop and exhibit a more uniform distribution by coupling film cooling, resulting in a low pattern factor. The combustion characteristics were then investigated and the optimization procedures of the fuel compositions and fuel flow rates were developed for future application of methane/syngas fuels in the micro gas turbine.

An Acoustic Time-of-Flight Approach for Unsteady Temperature Measurements: Characterization of Entropy Waves in a Model Gas Turbine Combustor

2016 ◽  
Vol 139 (4) ◽  
Author(s):  
Dominik Wassmer ◽  
Bruno Schuermans ◽  
Christian Oliver Paschereit ◽  
Jonas P. Moeck
Keyword(s):  
Gas Turbine ◽  
Acoustic Waves ◽  
Fuel Injection ◽  
Acoustic Pulse ◽  
Time Of Flight ◽  
Phase Lag ◽  
Mean Flow ◽  
Unsteady Temperature ◽  
Arrival Times ◽  
Flow Velocities

Lean premixed combustion promotes the occurrence of thermoacoustic phenomena in gas turbine combustors. One mechanism that contributes to the flame–acoustic interaction is entropy noise. Fluctuations of the equivalence ratio in the mixing section cause the generation of hot spots in the flame. These so-called entropy waves are convectively transported to the first stage of the turbine and generate acoustic waves that travel back to the flame; a thermoacoustic loop is closed. However, due to the lack of experimental tools, a detailed investigation of entropy waves in gas turbine combustion systems has not been possible up to now. This work presents an acoustic time-of-flight based temperature measurement method which allows the measurement of temperature fluctuations in the relevant frequency range. A narrow acoustic pulse is generated with an electric spark discharge close to the combustor wall. The acoustic response is measured at the same axial location with an array of microphones circumferentially distributed around the combustion chamber. The delay in the pulse arrival times corresponds to the line-integrated inverse speed of sound. For the measurement of entropy waves in an atmospheric combustion test rig, fuel is periodically injected into the mixing tube of a premixed combustor. The subsequently generated entropy waves are measured for different forcing frequencies of the fuel injection and for different mean flow velocities in the combustor. The amplitude decay and phase lag of the entropy waves adhere well to a Strouhal number scaling for different mean flow velocities.

Sign in / Sign up

Export Citation Format

Share Document