scholarly journals Direct and Inverse Heat Transfer Problems in Dynamics of Plate and Tube Heat Exchangers

10.5772/13572 ◽  
2011 ◽  
Author(s):  
Dawid Taler
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Inverse Heat Transfer ◽  
Transfer Problems

scholarly journals Solution to Two-Dimensional Steady Inverse Heat Transfer Problems with Interior Heat Source Based on the Conjugate Gradient Method

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Shoubin Wang ◽  
Li Zhang ◽  
Xiaogang Sun ◽  
Huangchao Jia
Keyword(s):  
Heat Transfer ◽  
Heat Source ◽  
Conjugate Gradient Method ◽  
Conjugate Gradient ◽  
Gradient Method ◽  
Measuring Error ◽  
Two Dimensional ◽  
Inverse Heat Transfer ◽  
Heat Transfer System ◽  
Transfer Problems

The compound variable inverse problem which comprises boundary temperature distribution and surface convective heat conduction coefficient of two-dimensional steady heat transfer system with inner heat source is studied in this paper applying the conjugate gradient method. The introduction of complex variable to solve the gradient matrix of the objective function obtains more precise inversion results. This paper applies boundary element method to solve the temperature calculation of discrete points in forward problems. The factors of measuring error and the number of measuring points zero error which impact the measurement result are discussed and compared with L-MM method in inverse problems. Instance calculation and analysis prove that the method applied in this paper still has good effectiveness and accuracy even if measurement error exists and the boundary measurement points’ number is reduced. The comparison indicates that the influence of error on the inversion solution can be minimized effectively using this method.

Conjugate Heat Transfer in Air-to-Refrigerant Airfoil Heat Exchangers

2014 ◽  
Vol 136 (8) ◽  
Author(s):  
Yutaka Ito ◽  
Naoya Inokura ◽  
Takao Nagasaki
Keyword(s):  
Heat Transfer ◽  
Carbon Dioxide ◽  
Heat Exchangers ◽  
Transfer Coefficients ◽  
Exchange System ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Heat Exchange System ◽  
Inverse Heat Transfer ◽  
Transfer Method

A light and compact heat exchange system was realized using two air-to-refrigerant airfoil heat exchangers and a recirculated heat transport refrigerant. Its heat transfer performance was experimentally investigated. Carbon dioxide or water was used as a refrigerant up to a pressure of 30 MPa. Heat transfer coefficients on the outer air-contact and inner refrigerant-contact surfaces were calculated using an inverse heat transfer method. Correlations were developed for the Nusselt numbers of carbon dioxide and water on the inner refrigerant-contact surface. Furthermore, we proposed a method to evaluate a correction factor corresponding to the thermal resistance of the airfoil heat exchanger.

scholarly journals Inverse heat transfer problem in digital temperature control in plate fin and tube heat exchangers

2011 ◽  
Vol 32 (4) ◽  
pp. 17-32 ◽  
Author(s):  
Dawid Taler ◽  
Adam Sury
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Temperature Control ◽  
Heat Exchangers ◽  
Pid Controller ◽  
Transfer Problem ◽  
Heat Transfer Problem ◽  
Inverse Heat Transfer ◽  
Inverse Heat Transfer Problem ◽  
Exit Temperature

Inverse heat transfer problem in digital temperature control in plate fin and tube heat exchangersThe aim of the paper is a steady-state inverse heat transfer problem for plate-fin and tube heat exchangers. The objective of the process control is to adjust the number of fan revolutions per minute so that the water temperature at the heat exchanger outlet is equal to a preset value. Two control techniques were developed. The first is based on the presented mathematical model of the heat exchanger while the second is a digital proportional-integral-derivative (PID) control. The first procedure is very stable. The digital PID controller becomes unstable if the water volumetric flow rate changes significantly. The developed techniques were implemented in digital control system of the water exit temperature in a plate fin and tube heat exchanger. The measured exit temperature of the water was very close to the set value of the temperature if the first method was used. The experiments showed that the PID controller works also well but becomes frequently unstable.

scholarly journals SOLVING TRANSIENT INVERSE HEAT TRANSFER PROBLEMS IN COMPLEX GEOMETRIES USING PHYSICS-GUIDED NEURAL NETWORKS (PGNN)

2021 ◽  
Vol 2021 (3) ◽  
pp. 4540-4547
Author(s):  
D. Emonts ◽  
◽  
J. Yang ◽  
R. H. Schmitt ◽  
◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flow ◽  
Input Parameter ◽  
Temperature Fields ◽  
Elastic Behavior ◽  
Transient Temperature ◽  
Complex Geometries ◽  
Inverse Heat Transfer ◽  
Geometric Inspection ◽  
Transfer Problems

Temporally and spatially unstable thermal conditions lead to transient or inhomogeneous thermo-elastic behavior of workpieces during manufacturing or geometric inspection. Temperature monitoring by means of sensors consign transient temperature fields, but do not yield information about the heat flow acting as thermal boundary condition, which is a relevant input parameter for nearly any thermal simulation. Addressing the need for efficient methods, the authors propose an approach to solve inverse heat transfer problems in complex geometries. In the presented study, locally acting heat loads are experimentally investigated based on virtual demonstrators running in FEM. The conducted method shows high potential for transient heat flow modelling in terms of accuracy and computational efficiency.

Sign in / Sign up

Export Citation Format

Share Document