scholarly journals Evaluation of Moisture Sensitivity Performance of Stone Mastic Asphalt Mixes with Additional Filler: A Laboratory Comparison of Dry and Wet Mixing Methods

2021 ◽  
Author(s):  
Altan CETIN
Keyword(s):  
Fly Ash ◽  
Hydrated Lime ◽  
Asphalt Mixtures ◽  
Filler Materials ◽  
Fine Aggregate ◽  
Moisture Susceptibility ◽  
Technical Specifications ◽  
Class C ◽  
Hot Mixed Asphalt ◽  
Class F

Gap-graded mixtures are one of the areas of improving the permanent deformation strength of hot-mixed asphalt mixtures. Additional filler materials can be needed due to the high bitumen amount and the less fine aggregate amount in the mixture. In this study, the effects of filler additives on moisture susceptibility of the gap-graded hot-mixed asphalt mixtures and mixing methods are investigated. Filler additives such as class C and class F fly ashes and hydrated lime are used 0.5 %, 1.0 %, 2.0 %, and 4 % of the total weight of mixture instead of mineral filler. Design mixtures are prepared according to the Turkish Highway Technical Specifications (THTS). To determine the effect of mixing methods, dry and wet (slurry) methods are used to mix the filler materials. Modified Lottman method (AASHTO T283) are used to determine the moisture susceptibility. An indirect tensile strength test is the measurement of bitumen film thickness which is also conducted. Test results showed that class C fly ash is significantly improved the moisture susceptibility of mixtures. While the slurry method does not give the expected improvement on class C fly ash added mixtures, it shows a positive effect on class F fly ash and hydrated lime added mixtures.

Influence of Cement Composition on Expansions Observed in Standard and Modified ASTM C1260 Test Procedures

2005 ◽  
Vol 1914 (1) ◽  
pp. 53-60 ◽  
Author(s):  
Prasada Rao Rangaraju ◽  
Ketan R. Sompura
Keyword(s):  
Fly Ash ◽  
Mitigation Measures ◽  
Fine Aggregate ◽  
Alkali Content ◽  
Test Procedures ◽  
Alkali Silica Reactivity ◽  
Class C ◽  
Class F Fly Ash ◽  
Different Sources ◽  
Class F

This paper presents the results of a laboratory study conducted to determine the influence of cement composition on the expansions observed in standard and modified ASTM C1260 tests. Also, the effectiveness of selected mitigation measures for alkali—silica reactivity was studied by using a modified ASTM C1260 test. Two different cements with substantially different alkali levels were used in combination with a Class F fly ash and a Class C fly ash. The results obtained from tests with 89 different sources of fine aggregate were analyzed. The results from this study indicate that cement composition has a distinct influence on the expansion levels observed in the ASTM C1260 study. For a majority of the aggregates tested in this study (88%), the use of a specific cement low in alkali content resulted in higher expansion than a cement with a relatively higher alkali content, regardless of the level of reactivity of the aggregate in the standard ASTM C1260 tests. Class F fly ash was found to be more effective than Class C fly ash in reducing the expansions in the modified ASTM C1260 tests. However, the cement used in the mixture influenced the percent reduction in expansion offered by both Class F fly ash and Class C fly ash. The use of low-alkali cement with Class F and Class C fly ashes yielded larger reductions in percent expansion.

scholarly journals Evaluations of Nano-Sized Hydrated Lime on the Moisture Susceptibility of Hot Mix Asphalt Mixtures

2012 ◽  
Vol 174-177 ◽  
pp. 82-90 ◽  
Author(s):  
Ju Nan Shen ◽  
Zhao Xing Xie ◽  
Fei Peng Xiao ◽  
Wen Zhong Fan
Keyword(s):  
Tensile Strength ◽  
Experimental Design ◽  
Hot Mix Asphalt ◽  
Hydrated Lime ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Moisture Resistance ◽  
Strength Ratio ◽  
Moisture Susceptibility ◽  
Indirect Tensile

The objective of this study was to evaluate the effect of nano-sized hydrated lime on the moisture susceptibility of the hot mix asphalt (HMA) mixtures in terms of three methodologies to introduce into the mixtures. The experimental design for this study included the utilizations of one binder source (PG 64-22), three aggregate sources and three different methods introducing the lime. A total of 12 types of HMA mixtures and 72 specimens were fabricated and tested in this study. The performed properties include indirect tensile strength (ITS), tensile strength ratio (TSR), flow, and toughness. The results indicated that the nano-sized lime exhibits better moisture resistance. Introducing process of the nano-sized lime will produce difference in moisture susceptibility.

Moisture susceptibility evaluation of asphalt mixtures containing Evonik, Zycotherm and hydrated lime

2018 ◽  
Vol 165 ◽  
pp. 958-965 ◽  
Author(s):  
Mahmoud Ameri ◽  
Mostafa Vamegh ◽  
Seyed Farhad Chavoshian Naeni ◽  
Mohammad Molayem
Keyword(s):  
Hydrated Lime ◽  
Asphalt Mixtures ◽  
Moisture Susceptibility ◽  
Susceptibility Evaluation

scholarly journals Experimental study on the properties of highperformance concrete made with class C fly ash

2019 ◽  
Vol 276 ◽  
pp. 01014
Author(s):  
I Made Alit Karyawan Salain ◽  
I Nyoman Sutarja ◽  
Teguh Arifmawan Sudhiarta
Keyword(s):  
Experimental Study ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Permeability Coefficient ◽  
Splitting Tensile Strength ◽  
Type I ◽  
Fine Aggregate ◽  
Hydration Time ◽  
Class C

This experimental study presents the properties of highperformance concrete (HPC) made by partially replacing type I Portland cement (OPC) with class C fly ash (CFA). The purpose of this study is to examine, with hydration time, the development of the compressive strength, the splitting tensile strength and the permeability of HPC utilizing different quantity of CFA. Four HPC mixtures, C1, C2, C3, and C4, were made by utilizing respectively 10%, 20%, 30% and 40% of CFA as replacement of OPC, by weight. One control mixture, C0, was made with 0% CFA. The mix proportion of HPC was 1.00 binder: 1.67 fine aggregate: 2.15 coarse aggregate with water to binder ratio 0.32. In each mixture, it was added 5% silica fume and 0.6% superplasticizer of the weight of the binder. Tests of HPC properties were realized at the age of 1, 3, 7, 28, and 90 days. The results indicate that CFA used to partially replace OPC in HPC shows adequate cementitious and pozzolanic properties. The compressive strength and the splitting tensile strength of HPC increase while the permeability coefficient decreases with increasing hydration time. It is found that the optimum replacement of OPC with CFA is 10%, however the replacement up to 20% is still acceptable to produce HPC having practically similar harden properties with control mixture. At this optimum replacement and after 90 days of hydration, the compressive strength, the splitting tensile strength and the permeability coefficient can reach 68.9 MPa, 8.3 MPa and 4.6 E-11 cm/sec respectively. These results are 109%, 101%, and 48% respectively of those of control mixture.

Evaluation of Moisture Susceptibility of Asphalt Mixtures: Conventional and New Methods

2000 ◽  
Vol 1728 (1) ◽  
pp. 43-51 ◽  
Author(s):  
N. Khosla ◽  
Brian G. Birdsall ◽  
Sachiyo Kawaguchi
Keyword(s):  
Tensile Strength ◽  
Friction Angle ◽  
Hydrated Lime ◽  
Asphalt Mixtures ◽  
Degree Of Saturation ◽  
Phosphate Ester ◽  
Simple Method ◽  
Moisture Sensitivity ◽  
Moisture Susceptibility ◽  
New Apparatus

Evaluation of a mixture’s moisture sensitivity is currently the final step in the Superpave® volumetric process. This step is accomplished by using AASHTO T-283, which tolerates a range of values in the test variables of sample air voids and degree of saturation. The tensile strength ratios determined for the mixes in this study varied with the air void level and degree of saturation. Although the levels of conditioning were within the specifications for AASHTO T-283, test results both passed and failed the 80 percent criterion, depending on the severity of conditioning. An alternative to measuring indirect tensile strength is a test that evaluates a mixture’s fundamental material properties. A relatively simple test is proposed that measures the cohesion and friction angle for asphalt mixtures. In addition, the Superpave shear tester (SST) was incorporated as a tool in evaluating moisture sensitivity. The proposed axial test determined the cohesion and angle of friction of the mix. The friction angle remained constant for the conditioned and unconditioned samples. Hence, conditioning of the samples had practically no effect on the mixture’s internal friction. The cohesion of the mix decreased when the mix was subjected to conditioning. The reduction in cohesion was greater in the case of the Fountain aggregate, which is known to be highly moisture susceptible. The shear tests to failure performed on the SST confirmed the results of the new apparatus, which provides a simple method for determining a mixture’s cohesion. The loss of cohesion due to conditioning can be used to determine a mixture’s moisture susceptibility. The three antistrip additives used in this study were hydrated lime, a liquid amine, and a liquid phosphate ester.

Effect of Partial Replacement of Fly Ash by Metakaolin on Strength Development of Fly Ash Based Geopolymer Mortar

2017 ◽  
Vol 744 ◽  
pp. 131-135 ◽  
Author(s):  
Muhammad Zahid ◽  
Nasir Shafiq ◽  
Mohd Fadhil Nuruddin ◽  
Ehsan Nikbakht ◽  
Asif Jalal
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide Solution ◽  
Base Material ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Partial Replacement ◽  
Strength Development ◽  
Class C ◽  
Class F

This article aims to investigate the compressive strength variation by the addition of metakaolin as a substitute of fly ash in the fly ash based geopolymer mortar. Five, ten and fifteen percent by weight of fly ash was replaced by highly reactive metakaolin. Two type of fly ashes namely, ASTM class F and ASTM class C were used as a base material for the synthesis of geopolymer mortar. Eight molar sodium hydroxide solution mixed with sodium silicate solution was used as alkaline activator. For optimum geopolymerization, mortar was cured at sixty degree Celsius for twenty four hours duration. Results show different behavior of metakaolin replacement on compressive strength for two different types of fly ash based geopolymer mortar. Improvement in compressive strength was seen by addition of metakaolin in ASTM class F fly ash based geopolymer. On the other hand compressive strength was decreased abruptly in fly ash class C based geopolymer up to certain replacement level.

Available Alkalis in Fly Ash

1985 ◽  
Vol 65 ◽  
Author(s):  
Chau Lee ◽  
Scott Schlorholtz ◽  
Turgut Demirel
Keyword(s):  
Fly Ash ◽  
Calcium Hydroxide ◽  
Fly Ashes ◽  
Class C ◽  
Time Required ◽  
Class F

ABSTRACTThe available alkalis of six Iowa fly ashes, four Class C and two Class F, have been studied as outlined by the procedures listed in ASTM C 311. The purposes of the study were to: (1) assess the significance of the test when it is used to analyze different fly ashes; (2) to investigate the possibility of decreasing the time required to complete the test (it currently requires 28 days for curing). When cured for 28 days at 38 C, the available alkalis were found to be about 60% and 30% of the total equivalent alkalis (equivalent alkalis = %Na20 + 0.658 × %K20) for Class C and Class F fly ashes, respectively. However, more than 85% and more than 40% of the total equivalent alkalis for the Class C and Class F fly ashes, respectively, were mobilized after 5 to 6 months of curing at 38 C. It was concluded that the available alkali test described in ASTM C 311 tends to underestimate the amount of equivalent alkalis present in Class C fly ash-calcium hydroxide mixtures after long periods of time.

Sign in / Sign up

Export Citation Format

Share Document