scholarly journals Influence of Laying Angles in Reinforcement of Epoxy in Sisal Plain Woven Structures

2021 ◽  
Author(s):  
Palani GOPINATH ◽  
Paramasivam SURESH
Keyword(s):  
Flexural Strength ◽  
Flexural Modulus ◽  
Strain Engineering ◽  
New Method ◽  
Epoxy Composites ◽  
Sisal Fiber ◽  
Engineering System ◽  
Data Sets ◽  
Displacement Force ◽  
Sisal Fibers

This study is about microstructure characterization and understanding the flexural properties of plain-woven sisal fabric reinforced epoxy composites. Vibrational Spectroscopy (FTIR) and SEM (Scanning Electron Microscopy) were used to describe the plain-woven sisal fabric and sisal fiber reinforced epoxy composites. Two laying angles were incorporated into the epoxy resin (10 percent), i.e. [0°/90°] and [0°/45°]. To isolate the effect of epoxy type and whether woven sisal fibers were used, an analytical design that is based on [0°/90°] and [0°/45°] orientation used the results. Epoxy treated with woven sisal fibers had a higher tensile (0.62 GPa) and flexural modulus (0.69 GPa) with tensile (17 MPa) and flexural strength (14 MPa) while being applied to a surface that is sloped at 0°/45° and which generates a displacement force of approximately 12 mm and strain 15.8 %. While conventional Weibull failure theory has long been widely used to explain the failure of brittle bulk materials, this new equation integrates that theory with the lay angle effect on flexural strength in plain sisal to calculate flexural strength reinforcement in epoxy. This new method can be applied to any fiber reinforcement, regardless of the type, and in terms of the failure of that reinforcement, which is governed by linear elastic fracture mechanics, and agreement between experimental data sets is excellent. According to our expectations, this theoretical study is going to provide a new method for the advanced strain engineering system to be built using reinforced fibers.

Effects of Weave Type and Fiber Content on Physical Properties of Sisal Fiber/Epoxy Composites

2010 ◽  
Vol 123-125 ◽  
pp. 1139-1142 ◽  
Author(s):  
Sawitri Srisuwan ◽  
Pranee Chumsamrong
Keyword(s):  
Impact Strength ◽  
Physical Properties ◽  
Epoxy Resin ◽  
Flexural Modulus ◽  
Fiber Content ◽  
Epoxy Composites ◽  
Sisal Fiber ◽  
Pure Epoxy ◽  
Sisal Fibers ◽  
The Impact

In this study, the effects of weave type and fiber content on the physical properties of woven sisal fiber/epoxy composites were investigated. Sisal fibers used in this work were obtained from Nakhon Ratchasima, Thailand. Both untreated and alkali-treated fibers were employed. The woven sisal fibers were manufactured by hand weaving process. The fiber content in sisal fiber/epoxy composites were 3 wt.%, 5 wt.% and 10 wt.%. The composites were cured at room temperatures. In order to determine mechanical properties of the composites, flexural and impact tests were applied. Flexural strength and flexural modulus of all composites were higher than those of pure epoxy resin and tended to increase with increasing fiber content. The impact strength of all composites was lower than that of pure epoxy resin. The composites containing 10 wt.% sisal fibers showed the highest impact strength. There was no definite influence of weave type on flexural properties of the composites. At 3 and 5 wt.% fiber, the composites containing plain weave fibers seemed to show a higher impact strength than the composites containing other weave types.

The Effects of Fiber Architecture and Fiber Surface Treatment on Physical Properties of Woven Sisal Fiber/Epoxy Composites

2011 ◽  
Vol 410 ◽  
pp. 39-42
Author(s):  
Sawitri Srisuwan ◽  
Pranee Chumsamrong
Keyword(s):  
Surface Treatment ◽  
Flexural Modulus ◽  
Fiber Surface ◽  
Epoxy Composites ◽  
Sisal Fiber ◽  
Fiber Architecture ◽  
Untreated Fiber ◽  
Fiber Surface Treatment ◽  
Sisal Fibers ◽  
Twill Weave

The aim of this work was to investigate the effects of fiber architecture and fiber surface treatment on flexural and impact properties of woven sisal fiber/epoxy composites. The woven sisal fibers with three different weave types including plain weave (P-weave), harness satin weave (S-weave) and right hand twill weave (R-weave) were used. For untreated fiber/epoxy composites, the fiber contents in the composite were 0, 5, 10 and 15% by weight (%wt). The untreated S-weave sisal fiber/epoxy composites showed the best overall properties and the composites with 15% fiber loading showed the highest properties. When compared to pure epoxy, flexural strength, flexural modulus and impact strength of the composite with 15% wt fiber increased by 4.5%, 60.6% and 150% respectively. Therefore, the composite of 15% wt silane treated S-weave and epoxy was prepared in order to study the effect of fiber surface treatment. The results showed that the composite containing 15% wt silane treated fiber possessed nearly the same properties with the untreated fiber/epoxy composite.

scholarly journals Enhanced flexural properties of aramid fiber/epoxy composites by graphene oxide

2019 ◽  
Vol 8 (1) ◽  
pp. 484-492 ◽  
Author(s):  
Yinqiu Wu ◽  
Bolin Tang ◽  
Kun Liu ◽  
Xiaoling Zeng ◽  
Jingjing Lu ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Flexural Strength ◽  
Interfacial Shear Strength ◽  
Flexural Modulus ◽  
Weight Fraction ◽  
Interfacial Shear ◽  
Aramid Fiber ◽  
Epoxy Composites ◽  
Flexural Properties ◽  
Pure Epoxy

Abstract The reinforcing effect of graphene oxide (GO) in enhancing the flexural strength and flexural modulus of aramid fiber (AF)/epoxy composites were investigated with GO-AFs at a weight fraction of 0.1-0.7%. The flexural strength and flexural modulus of the composite reached 87.16 MPa and 1054.7 MPa, respectively, which were about 21.19% and 40.86% higher than those of the pure epoxy resin, respectively. In addition, the flexural properties and interfacial shear strength (IFSS) of composite reinforced by GO-AFs were much higher than the composites reinforced by AFs due to GO improved the interfacial bonding between the reinforcement material and matrix.

Test Comparison Research Mechanics Performance between Sisal Fiber Concrete and Rubber Powder Concrete

2011 ◽  
Vol 243-249 ◽  
pp. 494-498
Author(s):  
Hui Ming Bao
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Sisal Fiber ◽  
Environment Friendly ◽  
Rubber Powder ◽  
Comparison Research ◽  
Mechanics Performance ◽  
Fiber Concrete ◽  
Sisal Fibers

By means of the tests on the mechanics performance of the reinforcing concrete mixed with sisal fibers or rubber powder of certain content are investigated. The compressive strength, tensile strength and flexural strength, etc. are compared. The test indicates that when the test condition is same, the compressive strength, tensile strength and flexural strength of the sisal fibers concrete are better than those of the rubber powder’s. The sisal fiber concrete is environment friendly than the rubber powder concrete. And it has widely value of spread and utilization.

scholarly journals Mechanical Characterization of Epoxy Filled with Seed Shells as Reinforcement

2019 ◽  
Vol 8 (4) ◽  
pp. 6972-6977
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Sodium Hydroxide ◽  
Natural Fiber ◽  
Fiber Composite ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
Epoxy Composites ◽  
The Matrix ◽  
Sunflower Seed Shells

The use of natural fiber composite has been widely promoted in many industries such as construction, automotive and even aerospace. Natural fibers can be extracted from plants that are abundantly available in the form of waste such as sunflower seed shells (SSS) and groundnut shells (GNS). These fibers were chosen as the reinforcement in epoxy to form composites. The performance of composites was evaluated following the ASTM D3039 and ASTM D790 for tensile and flexural tests respectively. Eight types of composites were prepared using SSS and GNS fibers as reinforcement and epoxy as the matrix with the fiber content of 20wt %. The fibers were untreated and treated with Sodium Hydroxide (NaOH) at various concentrations (6%, 10%, 15%, and 20%) and soaking time (24, 48 and 72 hours). The treatment has successfully enhanced the mechanical properties of both composites, namely SSS/epoxy and GNS/epoxy composites. The SSS/epoxy composite has the best mechanical properties when the fibers were treated for 48 hours using 6% of NaOH that produced 22 MPa and 13 MPa of tensile and flexural strength respectively. Meanwhile, the treatment on groundnut shells with 10% sodium Hydroxide for 24 hours has increased the Flexural strength tremendously (53%), however no significant effect on the tensile strength. The same trend was also observed on the tensile and flexural modulus. The increase of 41% in flexural modulus after treatment with 10% NaOH for 24 hours was also the evidence of mechanical properties enhancement. The evidence of improved fiber and matrix bonding after fiber treatment was also observed using a scanning electron microscope (SEM). The SSS/epoxy composites performed better in tensile application, meanwhile the GNS/epoxy composites are good in flexural application.

scholarly journals Injection Molded of Bio-Micro-Composites from Natural Fibers and Polylactic Acid

2017 ◽  
Vol 2 (1) ◽  
pp. 21-26
Author(s):  
Subyakto Subyakto ◽  
Euis Hermiati ◽  
Nanang Masruchin ◽  
Ismadi Ismadi ◽  
Kurnia Wiji Prasetiyo ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
Polylactic Acid ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
Tensile Modulus ◽  
Optimum Composition ◽  
Automotive Application ◽  
Composition Ratio ◽  
Sisal Fibers

Green composites were needed by automotive industries because they are environmentally friendly, recyclable, lightweight and strong. Natural fibers such as bamboo and sisal are potential source of these materials and can be used as substitutes of fiber glass which is hard to recycle and not renewable.  In this experiment, bio-composites made from micro fibers of betung bamboo (Dendrocalamus asper) and sisal (Agave sisalana) mixed with a natural polymer of polylactic acid (PLA) were developed that may used for automotive application. Bamboo or sisal fibers were converted into pulp and processed using a disc refiner to produce microfibrillated cellulose (MFC) with fiber diameter around 10 µm. MFC was mixed with PLA and triacetin and dried. The mixture was processed in a mixer at temperature of 170ºC, speed of 60 rpm for 20 min. The compound mixture was removed and processed into pellets using a pelletizer at 170ºC. Pellets were processed using injection molding machine. The compositions of fibers/PLA were 10/90, 20/80, and 30/70. The mechanical properties were tested in accordance with ASTM standards. Result shown that optimum composition ratio of bamboo fibers/PLA was 20/80 which gave flexural strength of 62.30 MPa, flexural modulus of 3.89 GPa, tensile strength of 44.55 MPa, tensile modulus of 1.20 GPa, and hardness of 112.90 R. While the optimum composition ratio of sisal fibers/PLA was 30/70 which gave flexural strength of 67.83 MPa, flexural modulus of 4.43 GPa, tensile strength of 48.18 MPa, tensile modulus of 1.13 GPa, and hardness of 110.50 R.

scholarly journals Halloysite reinforced epoxy composites with improved mechanical properties

2016 ◽  
Vol 18 (1) ◽  
pp. 133-135 ◽  
Author(s):  
Muhammad Jawwad Saif ◽  
Muhammad Asif ◽  
Muhammad Naveed ◽  
Khalid Mahmood Zia ◽  
Waheed -uz- Zaman ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Flexural Modulus ◽  
Halloysite Nanotubes ◽  
Epoxy Composites ◽  
Gravimetric Analysis ◽  
Thermal Gravimetric ◽  
Interfacial Coupling ◽  
Uniform Dispersion

Abstract Halloysite nanotubes (HNTs) reinforced epoxy composites with improved mechanical properties were prepared. The prepared HNTs reinforced epoxy composites demonstrated improved mechanical properties especially the fracture toughness and flexural strength. The flexural modulus of nanocomposite with 6% mHNTs loading was 11.8% higher than that of neat epoxy resin. In addition, the nanocomposites showed improved dimensional stability. The prepared halloysite reinforced epoxy composites were characterized by thermal gravimetric analysis (TGA). The improved properties are attributed to the unique characteristics of HNTs, uniform dispersion of reinforcement and interfacial coupling.

scholarly journals MECHANICAL PROPERTIES OF THE VIET NAM SISAL FIBRE REINFORCED POLYPROPYLENE COMPOSITE

2011 ◽  
Vol 14 (2) ◽  
pp. 29-36
Author(s):  
Nieu Huu Nguyen ◽  
Binh Thanh Phan ◽  
Sau Huynh
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Loss Modulus ◽  
Flexural Modulus ◽  
Dynamic Mechanical Properties ◽  
Sisal Fiber ◽  
Sisal Fibre ◽  
Dynamic Mechanical ◽  
Sisal Fibers ◽  
The Impact

The static mechanical and dynamic mechanical properties of the treated sisal fiber reinforced polypropylene composites were improved by adding the compatiblizer PPgMA (polypropylene-grafted-maleic anghydride). The mechanical properties of the composites have been evaluated. By increasing PPgMA dosages from 2% and 3.5% by weight of PP matrix; the impact strength of the composites were significantly improved by 27% and 38%; the elongation increased by 21% and 36%; the tensile strength increased by 35% and 95%; the elastic modulus increased by 21% and 94% and the flexural modulus increased by 2% and 83% respectively. The dynamic mechanical properties (the storage modulus E’, the loss modulus E” and the loss factor tanδ) have been investigated in relation to the compatibility between the PP matrix and the treated sisal fibers. E’ and E” increased by increasing dosage of PPgMA and Tg decreased a little when increasing the contents of PPgMA. At higher temperatures, tanδ increased and at lower temperature tanδ decreased when increasing dosage of PPgMA. It is shown that PP/treated sisal fibers/PPgMA composites have shown the effects of cohesion when increasing the PPgMA. The fiber dispersion was studied by the transmission optical microscope (TOM). The morphology of the composites samples fractured by the impact strength tests have been studied using scanning electronic microscopy (SEM). The results show the improvement of the interaction forces between treated sisal fibers and PP matrix at higher levels of PPgMA.

Degradation of Mechanical Properties of Conventional and Nanophased Carbon/Epoxy Composites in Seawater

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
M. K. Hossain ◽  
K. A. Imran ◽  
M. V. Hosur ◽  
S. Jeelani
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Flexural Modulus ◽  
Microscopy Study ◽  
Epoxy Composites ◽  
Molding Process ◽  
Bending Tests ◽  
Three Point Bending ◽  
Degradation Of Mechanical Properties ◽  
Marine Applications

Composites used for marine applications are subjected to various environmental effects, such as moisture, temperature, UV radiation, and seawater. In this study, effect of seawater on the degradation of mechanical properties of conventional and nanophased carbon/epoxy composites was investigated. Epoxy resin was modified using 1 wt. %, 2 wt. %, and 3 wt. % nanoclay. Carbon/epoxy composites were fabricated by vacuum assisted resin transfer molding process and compared with neat samples with and without exposure to seawater. Nanoclay was dispersed into matrix by using magnetic stirring. Mechanical characterization performed through three point bending tests showed that 2 wt. % nanoclay loading was optimum. Flexural strength and modulus were increased by 25% and 12.51%, respectively, compared to neat system for samples not exposed to seawater. Flexure samples exposed to the seawater for 30-, 60-, and 180-day periods revealed that samples with nanoclay retained better mechanical properties compared to neat samples. After 30-day exposure to seawater, there was no significant reduction in the strength and modulus. However, flexural strength was reduced by 10.24%, 7.08%, 5.28%, and 7.13% for neat, 1 wt. %, 2 wt. %, and 3 wt. % nanoclay-infused samples, respectively, after the samples were exposed to seawater for 180-day. At the same time flexural modulus was reduced by 12.61%, 7.16%, 4.59%, and 6.11%, respectively. From scanning electron microscopy (SEM) studies, it was found that failure occurred due to delimitation and initiated from the compression side. Nanophased composites exhibited better bonding between fiber and matrix. SEM micrographs also revealed that both unconditioned and conditioned nanophased epoxy, which produce relatively rougher fracture surfaces compared to neat samples. Optical microscopy study revealed no significant physical change in outer surfaces of the samples conditioned up to a 90-day period.

Mechanical and Physical Properties of Recycled Cellulose Fibre-Reinforced Epoxy Eco-Composites

2008 ◽  
Vol 41-42 ◽  
pp. 317-322 ◽  
Author(s):  
J. Sommers ◽  
H.S. Kho ◽  
R. Al-Ghamedi ◽  
It Meng Low ◽  
Ian J. Davies ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Impact Toughness ◽  
Flexural Strength ◽  
Flexural Modulus ◽  
Cellulose Fibre ◽  
Epoxy Composites ◽  
Ex Situ ◽  
Moderate Increase ◽  
Mechanical And Physical Properties

Epoxy composites reinforced with recycled cellulose fibre (RCF) have been synthesized and characterized. The reinforcement by RCF has resulted in a significant increase in the strain at break, fracture toughness and impact toughness but moderate increase in flexural strength and flexural modulus. The effect of seawater soaking on the flexural and impact properties has also been investigated. The micromechanisms of toughening and crack-tip failure processes are identified and discussed in the light of observed microstructures from in-situ and ex-situ fracture.

Sign in / Sign up

Export Citation Format

Share Document