scholarly journals Cyclic voltammetry: a simple method for determining contents of total and free iron ions in sodium ferric gluconate complex

2020 ◽  
Author(s):  
Hong Liu ◽  
Qiao Yu ◽  
Yixuan Ma ◽  
Baoyu Liu ◽  
Hongchun Pan
Keyword(s):  
Cyclic Voltammetry ◽  
Iron Content ◽  
Total Iron ◽  
Iron Ions ◽  
Experimental Conditions ◽  
Simple Method ◽  
Free Iron ◽  
Linear Relationships ◽  
Technological Level ◽  
Cv Measurements

<p class="PaperAbstract">Sodium ferric gluconate complex (SFGC) is the third generation of iron supplement of polysaccharide iron (III) complex (PIC). For evaluation of technological level and application value of the prepared SFGC, it would be of great significance to determine the iron content in SFGC in a simple but effective way. This paper introduces the cyclic voltammetry (CV) method for determination of iron content in SFGC. Under established optimal experimental conditions, the content of free iron ions can be directly scanned and calculated, while the total iron content can also be determined by completely acidifying SFGC into Fe<sup>3+</sup> ions. After optimizing and screening, the optimal scanning conditions are determined as pH 3 and 0.05 V/s of the scanning rate. Prior CV measurements, 0.4 V of the enrichment potential, and 3 min of the enrichment time are found optimal. It has also been verified that CO<sub>3</sub><sup>2-</sup> ions present in the solution show little interference in the system within the experimental range of investigation. The contents of free Fe<sup>3+</sup>, Fe<sup>2+</sup> ions and the total iron determined after acid-hydrolysis of SFGC can be accurately calculated according to the corresponding linear relationships between peak currents and iron concentrations. In this paper, the repeatability and accuracy of the method are verified, and its feasibility as a convenient and effective method to determine the iron supplements is confirmed.</p>

scholarly journals Suitability of the Cyclic Voltammetry Measurements and DPPH• Spectrophotometric Assay to Determine the Antioxidant Capacity of Food-Grade Oenological Tannins

Molecules ◽  
2019 ◽  
Vol 24 (16) ◽  
pp. 2925 ◽  
Author(s):  
Arianna Ricci ◽  
Giuseppina Paola Parpinello ◽  
Nemanja Teslić ◽  
Paul Andrew Kilmartin ◽  
Andrea Versari
Keyword(s):  
Cyclic Voltammetry ◽  
Colorimetric Assay ◽  
Radical Scavenging ◽  
Calibration Graph ◽  
Spectrophotometric Assay ◽  
Experimental Conditions ◽  
Fast Analysis ◽  
Cv Measurements ◽  
And Control ◽  
Analytical Approaches

Twenty commercially available oenological tannins (including hydrolysable and condensed) were assessed for their antiradical/reducing activity, comparing two analytical approaches: The 2,2-diphenyl-1-picrylhydrazyl (DPPH•) radical scavenging spectrophotometric assay and the cyclic voltammetry (CV) electrochemical method. Electrochemical measurements were performed over a −200 mV–500 mV scan range, and integrated anodic currents to 500 mV were used to build a calibration graph with (+)-catechin as a reference standard (linear range: From 0.0078 to 1 mM, R2 = 0.9887). The CV results were compared with the DPPH• assay (expressed as % of radical scavenged in time), showing high correlation due to the similarity of the chemical mechanisms underlying both methods involving polyphenolic compounds as reductants. Improved correlation was observed by increasing the incubation time with DPPH• to 24 h (R2 = 0.925), demonstrating that the spectrophotometric method requires a long-term incubation to complete the scavenging reaction when high-molecular weight tannins are involved; this constraint has been overcome by using instant CV measurements. We concluded that the CV represents a valid alternative to the DPPH• colorimetric assay, taking advantage of fast analysis and control on the experimental conditions and, because of these properties, it can assist the quality control along the supply chain.

scholarly journals Roles of Agrobacterium tumefaciens membrane-bound ferritin (MbfA) in iron transport and resistance to iron under acidic conditions

Microbiology ◽  
2014 ◽  
Vol 160 (5) ◽  
pp. 863-871 ◽  
Author(s):  
Sakkarin Bhubhanil ◽  
Jareeya Chamsing ◽  
Panida Sittipo ◽  
Paweena Chaoprasid ◽  
Rojana Sukchawalit ◽  
...  
Keyword(s):  
Agrobacterium Tumefaciens ◽  
Iron Content ◽  
Iron Transport ◽  
Protein Localization ◽  
Total Iron ◽  
Total Iron Content ◽  
Iron Storage ◽  
Free Iron ◽  
Membrane Bound ◽  
Acidic Conditions

Agrobacterium tumefaciens membrane-bound ferritin (MbfA) is a member of the erythrin (Er)–vacuolar iron transport family. The MbfA protein has an Er or ferritin-like domain at its N terminus and has been predicted to have five transmembrane segments in its C-terminal region. Analysis of protein localization using PhoA and LacZ reporter proteins supported the view that the N-terminal di-iron site is located in the cytoplasm whilst the C-terminal end faces the periplasm. An A. tumefaciens mbfA mutant strain had 1.5-fold higher total iron content than the WT strain. Furthermore, multi-copy expression of mbfA reduced total iron content two- and threefold in WT and mbfA mutant backgrounds, respectively. These results suggest that MbfA may function as an iron exporter rather than an iron storage protein. The mbfA mutant showed 10-fold increased sensitivity to the iron-activated antibiotic streptonigrin, implying that the mutant had increased accumulation of intracellular free iron. Growth of the mbfA mutant was reduced in the presence of high iron under acidic conditions. The expression of mbfA was induced highly in cells grown in iron-replete medium at pH 5.5, further supporting the view that mbfA is involved in the response to iron under acidic conditions. A. tumefaciens MbfA may play a protective role against increased free iron in the cytoplasm through iron binding and export, thus preventing iron-induced toxicity via the Fenton reaction.

A Simple Method for Estimation of Lipoxygenase and Cyclo-Oxygenase Pathways in Human Platelets - the Use of Thiobarbituric Acid Reaction

1980 ◽  
Vol 44 (02) ◽  
pp. 111-114 ◽  
Author(s):  
Hiroshi Takayama ◽  
Minoru Okuma ◽  
Haruto Uchino
Keyword(s):  
Time Course ◽  
Normal Values ◽  
Human Platelet ◽  
Thiobarbituric Acid ◽  
Human Platelets ◽  
Optimal Conditions ◽  
Experimental Conditions ◽  
Simple Method ◽  
Acid Reaction ◽  
Optimal Ph

SummaryTo develop a simple method for estimation of platelet lipoxygenase (PLO) and cyclo-oxygenase (PCO) pathways, the arachidonic acid (AA) metabolism of human platelet was investigated under various experimental conditions by the use of the thiobarbituric acid (TBA) reaction and a radioisotope technique. A TBA-reactive substance different from malondialdehyde (MDA) via PCO pathway was detected and shown to be derived from the PLO pathway. Since the optimal pH and time course of its formation were different from those of MDA formation via PCO pathway, PLO and PCO pathways were estimated by quantitating the TBA-reactive substances produced by the incubation of AA either with aspirin-treated platelets or with untreated ones, respectively, each under optimal conditions. Normal values expressed in terms of nmol MDA/108 platelets were 1.17±0.34 (M±SD, n = 31) and 0.79±0.15 (n = 31) for PLO and PCO pathways, respectively.

THE IMPACT OF WIND CONDITIONS ON THE LEVELS OF TOTAL IRON CONTENT IN THE SEA OF AZOV

2017 ◽  
Author(s):  
Yuri Fedorov ◽  
Yuri Fedorov ◽  
Irina Dotsenko ◽  
Irina Dotsenko ◽  
Leonid Dmitrik ◽  
...  
Keyword(s):  
Bottom Sediments ◽  
Iron Content ◽  
Iron Concentration ◽  
Total Iron ◽  
Sea Of Azov ◽  
Open Area ◽  
The Sea Of Azov ◽  
Dissolved Iron ◽  
The Impact ◽  
Taganrog Bay

The distribution and behavior of certain of trace elements in sea water is greatly affected by both physical, chemical and hydrometeorological conditions that are showed in the scientific works of prof. Yu.A. Fedorov with coauthors (1999-2015). Due to the shallow waters last factor is one of the dominant, during the different wind situation changes significantly the dynamics of water masses and interaction in the system “water – suspended matter – bottom sediments”.Therefore, the study of the behavior of the total iron in the water of the sea at different wind situation is relevant. The content of dissolved iron forms migration in The Sea of Azov water (open area) varies from 0.017 to 0.21 mg /dm3 (mean 0.053 mg /dm3) and in Taganrog Bay from 0.035 to 0.58 mg /dm3 (mean 0.11 mg /dm3) and it is not depending on weather conditions.The reduction in the overall iron concentration in the direction of the Taganrog Bay → The Sea of Azov (open area) is observed on average more than twice. The dissolved iron content exceeding TLV levels and their frequency of occurrence in the estuary, respectively, were higher compared with The Sea of Azov (open area).There is an increase in the overall iron concentration in the water of the Azov Sea on average 1.5 times during the storm conditions, due to the destruction of the structure of the upper layer and resuspension of bottom sediments, intensifying the transition of iron compounds in the solution.

scholarly journals Experimental Study on the Water Selective Dense Membrane under an Absolute Pressure Difference with Simplified Test Method

2021 ◽  
Vol 11 (4) ◽  
pp. 1710
Author(s):  
Jinwook Lee ◽  
Hyo-Sun Kim ◽  
Donik Ku ◽  
Jihun Lim ◽  
Minkyu Jung ◽  
...  
Keyword(s):  
Measurement Methods ◽  
Test Method ◽  
Coefficient Of Performance ◽  
Absolute Pressure ◽  
Air Conditioner ◽  
Experimental Conditions ◽  
Simple Method ◽  
Performance Factors ◽  
Dense Membrane ◽  
Before And After

Membrane-based vacuum dehumidification technology is currently being actively studied. In most studies, the performance of the membrane-based systems is evaluated under the assumption that the membrane can achieve ideal separation, which results in ideal coefficient of performance (COP) values. However, the performance factors for membranes vary depending on the experimental conditions and measurement methods. Therefore, relevant values can only be calculated if the data are measured in an environment close to that of the application conditions. The cup measurement method is a simple method to measure the permeability, however, there are limitations regarding adding variables during the experiment. To overcome these limitations, a new experimental device was constructed that combines pressurized cell with the cup method. Using the device, the performance of polyethylene-amide-bonded dense membranes was evaluated under conditions where absolute pressure differentials occurred before and after the membrane, such as in air conditioner dehumidification systems.

Effect of Domestic Processing and Cooking Methods on Total, HCl Extractable Iron and in vitro availability of Iron in Spinach and Amaranth Leaves

2002 ◽  
Vol 16 (2) ◽  
pp. 113-120 ◽  
Author(s):  
S.K. Yadav ◽  
S. Sehgal
Keyword(s):  
Iron Content ◽  
Dry Weight ◽  
Total Iron ◽  
Cooking Methods ◽  
In Vitro Availability ◽  
Domestic Processing ◽  
Polyethylene Bags ◽  
And Storage ◽  
Extractable Iron

Spinach ( Spinacia oleracia) and amaranth ( Amaranthus tricolor) leaves were stored in polyethylene bags and without packing for 24 and 48 hours in a refrigerator at 5°C and 30°C in polyethylene bags. The fresh leaves were also dried (oven and sun), blanched (5, 10 and 15 min) and cooked in an open pan and a pressure cooker. The processed leaves were analysed for total iron, its availability and antinutrient content. The iron content of these leaves varied from 26.54 to 34.14 mg/l00g, dry weight and its HCl-extractability and in vitro availability were 62.11–67.18% and 3.03–3.97% of total respectively. Drying and storage had no significant effect on total iron content, Hel-extractability and availability ( in vitro), while blanching and cooking resulted in significant improvement of iron availability, and a significant reduction in oxalic acid content, while only blanching significantly reduced phytic acid and polyphenol contents. Thus cooking and blanching are good ways to improve HCl-extractability and in vitro availability of iron.

Clay mineralogy of parent materials derived from uppermost Cretaceous and Tertiary sedimentary rocks in southern Saskatchewan

1993 ◽  
Vol 73 (4) ◽  
pp. 447-457 ◽  
Author(s):  
W. E. Dubbin ◽  
A. R. Mermut ◽  
H. P. W. Rostad
Keyword(s):  
Organic Carbon ◽  
Iron Content ◽  
Sedimentary Rocks ◽  
Clay Mineralogy ◽  
Total Iron ◽  
Total Iron Content ◽  
Parent Materials ◽  
Surface Areas ◽  
General Chemical ◽  
Detailed Chemical

Soils developed from parent materials derived from uppermost Cretaceous and Tertiary sedimentary rocks have been delineated from those which do not contain any of these younger sediments. The present study was initiated to determine the validity of this delineation. Parent materials from six locations in southwestern Saskatchewan were collected to determine their general chemical and physical properties. Clay fractions from each of these six parent materials were then subjected to detailed chemical and mineralogical analyses. The two parent materials containing the greatest amount of post-Bearpaw bedrock sediments (Jones Creek, Scotsguard) were characterized by substantially more organic carbon and less CaCO3. The presence of coal and the absence of carbonates in local bedrocks were considered to be the source of these deviations. In general, fine clays were comprised of 64–69% smectite, 14–21% illite and 10–13% kaolinite and coarse clay contained 32–39% smectite, 25–34% illite and 11–14% kaolinite. An exception was found in two fine clays which had less smectite but 3–6% vermiculite. Total iron content of the fine clays ranged from 7.16 to 8.11% expressed as Fe2O3. However, only a small fraction of this iron was extractable using the CDB technique. There were no substantial differences in surface areas or CECs of the clay fractions. Despite minor differences in the chemistry and mineralogy of these six parent materials, a separation of the soil associations does not appear to be warranted. Key words: Parent materials, uppermost Cretaceous, Tertiary, bedrock, clay mineralogy

Sign in / Sign up

Export Citation Format

Share Document