Strain Relaxation and Recovery Test (SRRT) on Waspaloy for Measuring Irreversible Strain Rate Equivalent to Minimum Creep Rate

2003 ◽  
Vol 49 (4) ◽  
pp. 173-178 ◽  
Author(s):  
N K Sinha ◽  
T. Terada ◽  
P. Au
Keyword(s):  
Creep Rate ◽  
Strain Rate ◽  
Minimum Creep Rate ◽  
Strain Relaxation ◽  
Recovery Test ◽  
Irreversible Strain

Extrapolation of Imaginal Minimum Creep Rate in Compression by a Concept of SATO-Index

2017 ◽  
Vol 741 ◽  
pp. 99-104
Author(s):  
Hiroyuki Sato
Keyword(s):  
Steady State ◽  
Creep Rate ◽  
Strain Rate ◽  
Creep Curve ◽  
Minimum Creep Rate ◽  
Steady State Creep ◽  
Steady State Creep Rate ◽  
Strain Rate Change ◽  
Primary Stage ◽  
Strain Dependence

Creep characteristics of alloys and compounds have been evaluated mainly by the minimum creep rate or the steady-state creep rate, and by its stress and temperature dependences. In some cases, however, direct comparison of the minimum creep rate or the steady-state creep rate are not practically easy due to difficulties of experiment, i.e., a long duration of primary stage of creep deformation. The minimum creep rates are not always precise representative value, which is directly evaluated from experiments. It should be valuable, if one could estimate the minimum creep rate from creep curve in primary stage. I have proposed a method of quantitative evaluation of creep curve based on the evaluation of strain rate change and its strain dependence during creep [1-3]. The value that reflects a shape of creep curve is named “Strain Acceleration and Transition Objective-Index (SATO-Index)” [4]. SATO-Index and related differential equation show a strain dependence of strain rate and lead entre creep curve by numerical integration. This concept provides quantitative information of shape of each creep curve, and information of the entire creep curve. In this paper, examples of evaluation and extrapolation of creep rate from primary stage in compression are presented. It is concluded that the extrapolation with the concept of SATO-Index reasonably provides imaginal minimum creep rate. Usability of extrapolation of creep curve by the concept is presented.

scholarly journals Effect of Low-Temperature Annealing on Creep Properties of AlSi10Mg Alloy Produced by Additive Manufacturing: Experiments and Modeling

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 179
Author(s):  
Chiara Paoletti ◽  
Emanuela Cerri ◽  
Emanuele Ghio ◽  
Eleonora Santecchia ◽  
Marcello Cabibbo ◽  
...  
Keyword(s):  
Creep Rate ◽  
Applied Stress ◽  
Minimum Creep Rate ◽  
Annealing Treatment ◽  
Constant Load ◽  
Experimental Conditions ◽  
Creep Properties ◽  
Low Temperature Annealing ◽  
Physically Based ◽  
Excellent Description

The effects of postprocessing annealing at 225 °C for 2 h on the creep properties of AlSi10Mg alloy were investigated through constant load experiments carried out at 150 °C, 175 °C and 225 °C. In the range of the experimental conditions here considered, the annealing treatment resulted in an increase in minimum creep rate for a given stress. The reduction in creep strength was higher at the lowest temperature, while the effect progressively vanished as temperature increased and/or applied stress decreased. The minimum creep rate dependence on applied stress was modeled using a physically-based model which took into account the ripening of Si particles at high temperature and which had been previously applied to the as-deposited alloy. The model was successfully validated, since it gave an excellent description of the experimental data.

Evaluation of Creep Deformation Property of Grade 91 Steels

2015 ◽  
Author(s):  
Kazuhiro Kimura ◽  
Kota Sawada ◽  
Hideaki Kushima
Keyword(s):  
Creep Rate ◽  
Creep Deformation ◽  
Minimum Creep Rate ◽  
Deformation Property ◽  
Time Dependent ◽  
Tertiary Creep ◽  
Total Strain ◽  
Dominant Factor ◽  
Creep Equation ◽  
Time To Rupture

Creep deformation property of Grade T91 steels over a range of temperatures from 550 to 625°C was analyzed by means of the empirical creep equation reported in the previous study [1]. The creep equation consists of four time dependent terms and one constant and time to rupture is estimated as a time to total strain of 10%. Accuracy of the creep equation to represent creep curve and to predict time to rupture and minimum creep rate was indicated. Times to minimum creep rate, total strain of 1%, initiation of tertiary creep and rupture were evaluated by the creep equation. Stress dependence of strains at minimum creep rate and the initiation of tertiary creep were analyzed. Contribution of four time dependent terms to the strains at minimum creep rate, total strain of 1% and initiation of tertiary creep was investigated. Three parameters to determine a temperature and time-dependent stress intensity limit, St, were compared and a dominant factor of St was examined. Heat-to-heat variation of the creep deformation property was investigated on two heats of T91 steels contain low and high nickel concentrations.

Investigation on Creep Behavior of Grade 91 Heat-Resistant Steel at 923K

2016 ◽  
Vol 853 ◽  
pp. 163-167
Author(s):  
Fa Cai Ren ◽  
Xiao Ying Tang
Keyword(s):  
Creep Rate ◽  
Creep Behavior ◽  
Creep Deformation ◽  
Deformation Behavior ◽  
Minimum Creep Rate ◽  
Resistant Steel ◽  
Creep Tests ◽  
Heat Resistant Steel ◽  
Heat Resistant ◽  
Grade 91

Creep deformation behavior of SA387Gr91Cl2 heat-resistant steel used for steam cooler has been investigated. Creep tests were carried out using flat creep specimens machined from the normalized and tempered plate at 973K with stresses of 100, 125 and 150MPa. The minimum creep rate and rupture time dependence on applied stress was analyzed. The analysis showed that the heat-resistant steel obey Monkman-Grant and modified Monkman-Grant relationships.

Creep Deformation Behavior and Microstructural Degradation During Creep of Pre-Strained 25Cr-20Ni-Nb-N Steel

2007 ◽  
Author(s):  
Nobuhiko Saito ◽  
Nobuyoshi Komai
Keyword(s):  
Creep Rate ◽  
Creep Deformation ◽  
Deformation Behavior ◽  
Minimum Creep Rate ◽  
Strengthening Mechanism ◽  
Creep Rupture ◽  
Microstructural Degradation ◽  
Solution Treated ◽  
Long Time ◽  
Strained Materials

The purpose of this study is to clarify the creep deformation behavior and microstructural degradation during creep of pre-strained 25Cr-20Ni-Nb-N steel (TP310HCbN), which has the highest creep strength among austenite stainless steels used for boiler tubes. The creep rupture strengths of the 20% pre-strained materials tested at 650°C under 210 MPa and 180 MPa were higher than those of solution-treated materials. However, the long time creep rupture strengths of the 20% pre-strained materials tested at 700°C and 750°C were lower than those of solution-treated materials. Thus, the creep strengths of the prestrained materials depend on test temperature and stress. Furthermore, the minimum creep rate of the 20% pre-strained materials and re-solution-treated materials tested at 650°C under 300MPa were 1.2 × 10−9 and 1.6 × 10−8 s−1, respectively. Thus, the minimum creep rate of the 20% pre-strained materials was lower than for re-solution-treated materials. The creep strengthening mechanism of the pre-strained materials at 650°C was considered to be that high-density dislocations were maintained until the late stage of creep. On the other hand, the creep rupture strengths of the 20% pre-strained materials were lower than those of solution-treated materials tested at over 700°C because of agglomeration and coarsening of precipitates and the recovery of dislocations.

The Creep Deformation and Elevated Temperature Microstructural Stability of a Two-Phase TiAl/Ti3Al Lamellar Alloy.

1994 ◽  
Vol 364 ◽  
Author(s):  
M. F. Bartholomeusz ◽  
J. A. Wert
Keyword(s):  
Elevated Temperature ◽  
Creep Rate ◽  
Microstructural Evolution ◽  
Creep Deformation ◽  
Minimum Creep Rate ◽  
Single Phase ◽  
Lamellar Microstructure ◽  
Microstructural Stability ◽  
Two Phase ◽  
The Individual

AbstractEnhanced work hardening of the phases in the lamellar microstructure has been cited as an explanation for the lower minimum creep rates of a two-phase TiAl/Ti3Al lamellar alloy compared with the minimum creep rates of the individual TiAl and Ti3Al single-phase alloys tested between 980 K and 1130 K. This proposition is confirmed by TEM observations. Thermal and thermomechanical exposure result in the microstructural evolution, which increases the minimum creep rate (εmin) of the lamellar alloy. The effect of microstructural evolution on εmin will be discussed in the present paper.

On the minimum creep rate of β-cobalt

1964 ◽  
Vol 10 (104) ◽  
pp. 355-356 ◽  
Author(s):  
T. A. Myers ◽  
P. Feltham
Keyword(s):  
Creep Rate ◽  
Minimum Creep Rate
Sign in / Sign up

Export Citation Format

Share Document