scholarly journals EFFECTS OF MECHANICAL PROPERTY VARIABILITY IN LEAD RUBBER BEARINGS ON THE RESPONSE OF SEISMIC ISOLATION SYSTEM FOR DIFFERENT GROUND MOTIONS

2014 ◽  
Vol 46 (5) ◽  
pp. 605-618 ◽  
Author(s):  
YOUNG-SUN CHOUN ◽  
JUNHEE PARK ◽  
IN-KIL CHOI
Keyword(s):  
Mechanical Property ◽  
Seismic Isolation ◽  
Ground Motions ◽  
Isolation System ◽  
Lead Rubber Bearings ◽  
Rubber Bearings

scholarly journals Optimum parameters of a five-story building supported by lead-rubber bearings under near-fault ground motions

2019 ◽  
Vol 39 (1) ◽  
pp. 98-113 ◽  
Author(s):  
Qiang Rong
Keyword(s):  
Ground Motions ◽  
Isolation System ◽  
Optimum Yield ◽  
Shear Coefficient ◽  
Near Fault ◽  
Optimum Parameters ◽  
Yield Displacement ◽  
Lead Rubber Bearings ◽  
Rubber Bearings ◽  
Isolation Period

Seismic response of five-story frame structure supported by lead-rubber bearings isolation system is investigated subjected to near-fault ground motions. The main structure is modeled as a simple linear multi-degrees-of-freedom vibration system with lumped masses, excited by near-fault ground motions in the horizontal direction. The variation curves of peak top floor acceleration and peak bearing displacement of isolated building are plotted under different yield shear coefficient. The objective function selected for optimality is to maximize the seismic energy dissipated by the lead-rubber bearings. The main constraint conditions selected for optimality are the minimization of both peak bearing displacement and peak top floor acceleration. Optimum parameters of lead-rubber bearing isolation system are investigated and found that optimum yield shear coefficient of lead-rubber bearings is found to be in the range of 0.10–0.14 under near-fault ground motions. Optimum yield shear coefficient decreases with the increase of second isolation period. Optimum yield shear coefficient of lead-rubber bearings with higher yield displacement is larger than that of lead-rubber bearings with low yield displacement. Optimum ratio of pre-yield stiffness to post-yield stiffness of lead-rubber bearings is found to be in the range of 16–35. Optimum stiffness ratio increases proportionally with the decrease of yield displacement. Optimum stiffness ratio increases slightly with the increase of yield shear coefficient. Excluding the effect of pre-yield stiffness, the optimum second isolation period is recommended to be in the range of 4–6 s.

The Behavior of Bearings Used for Seismic Isolation under Rotation and Axial Load

1999 ◽  
Vol 15 (2) ◽  
pp. 225-244 ◽  
Author(s):  
Atsushi Mori ◽  
Peter J. Moss ◽  
Nigel Cooke ◽  
Athol J. Carr
Keyword(s):  
Seismic Isolation ◽  
Axial Loads ◽  
Isolation System ◽  
Elastomeric Bearings ◽  
Lead Rubber Bearings ◽  
Combined Action ◽  
Lift Off ◽  
Rubber Bearings ◽  
Bearing Behavior ◽  
Angle Of Rotation

The investigation described in this paper looked at both laminated elastomeric bearings and lead-rubber bearings in order to obtain a better understanding of the real bearing behavior under the combined action of rotation and axial loads when used in a seismic-isolation system. In particular, the investigation focused on the distributions of vertical pressure on the bearing faces and the degree of lift-off of the edges of the bearings as the angle of rotation increased.

The Behavior of Bearings Used for Seismic Isolation under Shear and Axial Load

1999 ◽  
Vol 15 (2) ◽  
pp. 199-224 ◽  
Author(s):  
Atsushi Mori ◽  
Peter J. Moss ◽  
Nigel Cooke ◽  
Athol J. Carr
Keyword(s):  
Seismic Isolation ◽  
Axial Loads ◽  
Isolation System ◽  
Elastomeric Bearings ◽  
Lead Rubber Bearings ◽  
Combined Action ◽  
Lift Off ◽  
Rubber Bearings ◽  
Bearing Behavior ◽  
Angle Of Rotation

The investigation described in this paper looked at both laminated elastomeric bearings and lead-rubber bearings in order to obtain a better understanding of the real bearing behavior under the combined action of shear and axial loads when used in a seismic-isolation system. In particular, the investigation focused on the distributions of vertical pressure on the bearing faces and the degree of lift-off of the edges of the bearings as the shearing displacement and the angle of rotation increased.

scholarly journals Seismic isolation of a printing press in Wellington, New Zealand

1992 ◽  
Vol 25 (3) ◽  
pp. 161-166 ◽  
Author(s):  
D. J. Dowrick ◽  
J. Babor ◽  
W. J. Cousins ◽  
R. I. Skinner
Keyword(s):  
Cast Iron ◽  
New Zealand ◽  
Seismic Hazard ◽  
Seismic Isolation ◽  
Printing Press ◽  
Isolation System ◽  
Building Housing ◽  
The Press ◽  
Lead Rubber Bearings ◽  
Rubber Bearings

This paper describes the seismic hazard near the Wellington Fault in Petone, and the measures taken to protect a new printing press made of brittle cast iron against earthquake attack. The printing press, owned by Wellington Newspapers, was located just 20 m from the Wellington Fault. Mounting the specially designed building housing the press on a seismic isolation system, lead-rubber bearings, reduced the estimated loads and deflections on the press by a factor of 8-10 compared with the non-isolated case. As a result the press should suffer only modest damage in earthquake shaking somewhat stronger than that required by the New Zealand earthquake code for the design of buildings.

scholarly journals Seismic isolation system of two hinged arch suspended-deck bridge: a case study on Kalikuto bridge - Indonesia

2020 ◽  
Vol 156 ◽  
pp. 05024
Author(s):  
Tri Suryadi ◽  
Arvila Delitriana ◽  
Zdenek Fukar ◽  
Rusri Tjendana
Keyword(s):  
Seismic Isolation ◽  
Performance Tests ◽  
Isolation System ◽  
Expansion Joints ◽  
Lead Rubber Bearings ◽  
Design Requirements ◽  
Isolation Systems ◽  
Rubber Bearings ◽  
Seismic Isolation Systems

Seismic isolation systems are widely used in buildings, bridges, and industrial structures all over the world. The system is known for the efficiency to reduce earthquake demand and thus provide better seismic performance of the structures. In particular to application in an arch suspended-deck bridge, seismic isolation system can be a solution for the seismic resisting system due to the incapability of the cable hangers to transfer horizontal forces from excitation mass on the hanging deck to the main compression arches. Kalikuto arch bridge that is built in 2018 has implemented both Lead Rubber Bearings and Seismic Rubber Expansion Joints as the part of its seismic resisting system. These two seismic isolation devices were designed and engineered accurately to fulfil the seismic design requirements of the Kalikuto bridge. Finally, several performance tests were conducted to evaluate the design compliance of the manufactured devices.

Research on the Effect of Combined Seismic Isolation System

2012 ◽  
Vol 446-449 ◽  
pp. 3299-3303
Author(s):  
Xi Sen Fan ◽  
Ting Lei Tian
Keyword(s):  
Seismic Response ◽  
Seismic Isolation ◽  
Base Isolation ◽  
Seismic Responses ◽  
Combined System ◽  
Isolation System ◽  
Lead Rubber Bearings ◽  
Base Isolation System ◽  
Rubber Bearings ◽  
The Relationship

The isolation system between the upper structure and the foundation could reduce the seismic response of the former. A system combined of sliding and lead rubber bearings (LRB) is more effective in seismic isolation than using the later alone. In this research, the seismic responses of a building which was set with LRB and a combined system (the proportions between the sliding and LRB were 1/6, 1/4 and 1/3) respectively were analyzed and compared to that of the building without base isolation system to investigate the effect of seismic isolation. The relationship between isolation coefficient and the proportion of bearings was studied. The results show that the combined system could reduce the seismic response of structure, and it is more effective in seismic isolation if the leading bearing is relatively more.

DESIGN FORCE TRANSMITTED BY ISOLATION SYSTEM COMPOSED OF LEAD-RUBBER BEARINGS AND VISCOUS DAMPERS

2010 ◽  
Vol 10 (02) ◽  
pp. 287-298 ◽  
Author(s):  
J. S. HWANG ◽  
C. F. HUNG ◽  
Y. N. HUANG ◽  
S. J. WANG
Keyword(s):  
Phase Angle ◽  
Seismic Isolation ◽  
Soft Soil ◽  
Near Field ◽  
Viscous Dampers ◽  
Maximum Displacement ◽  
Isolation System ◽  
Lead Rubber Bearings ◽  
Response History Analysis ◽  
Rubber Bearings

In seismic isolation design of structures located at soft soil sites or near field areas, viscous dampers (VD) are often included as part of the isolation system to minimize its maximum displacement. Due to the 90° phase angle existing between the force and displacement of the VD, the maximum force transmitted by the isolation system cannot be calculated by simply combining the forces of the isolation bearings, such as lead-rubber bearings (LRB) or high damping rubber bearings (HDRB), and VD in association with the design displacement. Conforming to the code-specified equivalent lateral response procedure for isolation design, this paper presents a formula for determining the seismic design force of the combined LRB and VD isolation system, taking into account the phase angle between the combined force of the LRB and VD and the displacement of the isolation system. The numerical results have shown that the maximum responses of the isolation system predicted by the proposed formula are conservative and comparable with those from the inelastic dynamic response history analysis.

Seismic Isolation Analysis on Long-Span Platform Bridge Connecting Twin-Tower Structures

2011 ◽  
Vol 255-260 ◽  
pp. 1225-1229
Author(s):  
Huang Sheng Sun ◽  
Li Nuo Cheng ◽  
Shi Hai Chen
Keyword(s):  
Seismic Isolation ◽  
Seismic Responses ◽  
One Pot ◽  
Isolation System ◽  
High Position ◽  
Long Span ◽  
Steel Truss ◽  
Story Drift ◽  
Isolation Systems ◽  
Rubber Bearings

In order to mitigate the seismic response of twin-tower structure linked by a steel truss platform bridge, as well as to reduce temperature force in the steel truss, eight groups of combined isolation system, each consisting of one pot-type bearing and four rubber bearings, were designed to connect the upper platform bridge to the lower supporting reinforced concrete towers. The features and working principles of the high-position isolation system were described. Then the seismic responses, including displacement, story drift and floor acceleration, of the structure with the isolation systems were calculated and compared with those of the structure with hinge joints in lieu of isolation. It is found that both the structural seismic responses and the temperature forces in the large-span mega-truss structure can be reduced by the high-position isolation system.

Fundamental Study on the Super-Long-Period Active Isolation System

2004 ◽  
Author(s):  
Keisuke Minagawa ◽  
Satoshi Fujita
Keyword(s):  
Control System ◽  
Seismic Isolation ◽  
Seismic Waves ◽  
Model Matching ◽  
Fundamental Study ◽  
Natural Period ◽  
Isolation System ◽  
Long Period ◽  
Rubber Bearings ◽  
Classical Control

Since the Hanshin-Awaji Earthquake Disaster, the number of isolated structures has been greatly increased. The natural period of the isolation system is designed around 3 seconds, because predominate period of observed seismic waves is usually 0.1 to 1 second. However, relatively long period seismic waves have been observed in various earthquakes, and the resonance of long-period structures, such as high-rise buildings, during earthquakes have been reported at the same time. Therefore the natural period needs to be extended. When extending the natural period of the isolated structure using rubber bearings, its stiffness needs to be reduced. It is more difficult to extend the natural period of the isolation system than the conventional system because of its buckling problem. Therefore we propose a super-long-period active seismic isolation system as a new method for extending the natural period of the isolated structure. This system consists of rubber bearings and actuators. In this study, we designed a control system by using the model-matching-method. This is one of the classical control system design methods. We investigated the isolation performance by numerical analysis. In addition, we selected the optimal variables of transfer function using genetic algorithm.

Sign in / Sign up

Export Citation Format

Share Document