scholarly journals Design and Simulation of Multiquantum-Well AlGaAs/GaAs Single Junction Solar Cell with Back Surface Reflector

2012 ◽  
Vol 2012 ◽  
pp. 1-5
Author(s):  
Hamid Fardi
Keyword(s):  
Solar Cell ◽  
Cell Structure ◽  
Short Circuit ◽  
Cell Junction ◽  
Back Surface ◽  
Nonradiative Recombination ◽  
Hot Electron ◽  
Single Junction ◽  
Short Circuit Currents ◽  
Multiquantum Well

This paper reports on the design and simulation of a multiquantum Well (MQW) AlGaAs/GaAs single p-i-n junction cell with a Distributed Bragg Reflector (DBR) placed at back surface. The DBR structure reflects the part of the spectrum that benefits from absorption in the AlGaAs MQW structure, while being transparent to the IR spectrum. The addition of a DBR allows for a possible second bottom cell junction to be placed beneath the DBR in series with the MQW single cell for an additional efficiency enhancement. The efficiencies and short-circuit currents for the AlGaAs MQW cell with and without DBR are simulated. An energy balance equations model coupled with drift-diffusion equations is solved in heterojunction p-i-n with embedded quantum wells to model hot electron effects. The current-voltage characteristics of an MQW single junction AlGaAs/GaAs p-i-n solar cell structure were compared with measured data. The efficiencies and short-circuit currents of an optimized cell with and without DBR are simulated. Results obtained show improvement in short circuit current and efficiency when both MQW and DBR were used. Simulation results predict an efficiency of about 28.4% for the MQW AlGaAs-DBR single p-i-n junction photovoltaic cell under the presence of both radiative and nonradiative recombination mechanisms.

scholarly journals Numerical Investigation of Graphene as a Back Surface Field Layer on the Performance of Cadmium Telluride Solar Cell

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3275
Author(s):  
Devendra KC ◽  
Deb Kumar Shah ◽  
M. Shaheer Akhtar ◽  
Mira Park ◽  
Chong Yeal Kim ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Doping Concentration ◽  
Carrier Lifetime ◽  
Short Circuit ◽  
Back Surface ◽  
Back Surface Field ◽  
Cdte Solar Cell ◽  
Cdte Solar Cells ◽  
Surface Field

This paper numerically explores the possibility of ultrathin layering and high efficiency of graphene as a back surface field (BSF) based on a CdTe solar cell by Personal computer one-dimensional (PC1D) simulation. CdTe solar cells have been characterized and studied by varying the carrier lifetime, doping concentration, thickness, and bandgap of the graphene layer. With simulation results, the highest short-circuit current (Isc = 2.09 A), power conversion efficiency (h = 15%), and quantum efficiency (QE ~ 85%) were achieved at a carrier lifetime of 1 × 103 ms and a doping concentration of 1 × 1017 cm−3 of graphene as a BSF layer-based CdTe solar cell. The thickness of the graphene BSF layer (1 mm) was proven the ultrathin, optimal, and obtainable for the fabrication of high-performance CdTe solar cells, confirming the suitability of graphene material as a BSF. This simulation confirmed that a CdTe solar cell with the proposed graphene as the BSF layer might be highly efficient with optimized parameters for fabrication.

Enhancement of the performance of CdS/CdTe heterojunction solar cell using TiO2/ZnO bi-layer ARC and V2O5 BSF layers: A simulation approach

2020 ◽  
Vol 92 (2) ◽  
pp. 20901
Author(s):  
Abdul Kuddus ◽  
Md. Ferdous Rahman ◽  
Jaker Hossain ◽  
Abu Bakar Md. Ismail
Keyword(s):  
Solar Cell ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Heterojunction Solar Cell ◽  
Back Surface ◽  
Heterojunction Solar Cells

This article presents the role of Bi-layer anti-reflection coating (ARC) of TiO2/ZnO and back surface field (BSF) of V2O5 for improving the photovoltaic performance of Cadmium Sulfide (CdS) and Cadmium Telluride (CdTe) based heterojunction solar cells (HJSCs). The simulation was performed at different concentrations, thickness, defect densities of each active materials and working temperatures to optimize the most excellent structure and working conditions for achieving the highest cell performance using obtained optical and electrical parameters value from the experimental investigation on spin-coated CdS, CdTe, ZnO, TiO2 and V2O5 thin films deposited on the glass substrate. The simulation results reveal that the designed CdS/CdTe based heterojunction cell offers the highest efficiency, η of ∼25% with an enhanced open-circuit voltage, Voc of 0.811 V, short circuit current density, Jsc of 38.51 mA cm−2, fill factor, FF of 80% with bi-layer ARC and BSF. Moreover, it appears that the TiO2/ZnO bi-layer ARC, as well as ETL and V2O5 as BSF, could be highly promising materials of choice for CdS/CdTe based heterojunction solar cell.

Numerical Simulation of Single Junction InGaN Solar Cell by SCAPS

2019 ◽  
Vol 821 ◽  
pp. 407-413 ◽  
Author(s):  
Mohamed Orabi Moustafa ◽  
Tariq Alzoubi
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Collection Efficiency ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Surface Recombination ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Bandgap Energy ◽  
Single Junction

The performance of the InGaN single-junction thin film solar cells has been analyzed numerically employing the Solar Cell Capacitance Simulator (SCAPS-1D). The electrical properties and the photovoltaic performance of the InGaN solar cells were studied by changing the doping concentrations and the bandgap energy along with each layer, i.e. n-and p-InGaN layers. The results reveal an optimum efficiency of the InGaN solar cell of ~ 15.32 % at a band gap value of 1.32 eV. It has been observed that lowering the doping concentration NA leads to an improvement of the short circuit current density (Jsc) (34 mA/cm2 at NA of 1016 cm−3). This might be attributed to the increase of the carrier mobility and hence an enhancement in the minority carrier diffusion length leading to a better collection efficiency. Additionally, the results show that increasing the front layer thickness of the InGaN leads to an increase in the Jsc and to the conversion efficiency (η). This has been referred to the increase in the photogenerated current, as well as to the less surface recombination rate.

High-efficiency CIGS solar cell by optimization of doping concentration, thickness and energy band gap

2019 ◽  
Vol 34 (04) ◽  
pp. 2050053
Author(s):  
Fatemeh Ghavami ◽  
Alireza Salehi
Keyword(s):  
Solar Cell ◽  
Band Gap ◽  
High Efficiency ◽  
Cell Structure ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Absorber Layer ◽  
Window Layer

In this paper, the performance of copper-indium-gallium-diselenide Cu(In,Ga)Se2 solar cell, with ZnO window layer, ZnSe buffer layer, CIGS absorber layer and InGaP reflector layer was studied. The study was performed using the TCAD Silvaco simulator. The effects of grading the band gap of CIGS absorber layer, the various thicknesses and doping concentrations of different layers have been investigated. By optimizing the solar cell structure, we have obtained a maximum open circuit voltage of 0.91901 V, a short circuit current density of 39.89910 mA/cm2, a fill factor (FF) of 86.67040% and an efficiency of 31.78% which is much higher than the values for similar CIGS solar cells reported so far.

Guiding Principle to Develop Intrinsic Microcrystalline Silicon Absorber Layer For Solar Cell By Hot-Wire Cvd

2001 ◽  
Vol 664 ◽  
Author(s):  
A. R. Middya ◽  
U. Weber ◽  
C. Mukherjee ◽  
B. Schroeder
Keyword(s):  
Growth Rate ◽  
Solar Cell ◽  
Cell Structure ◽  
Short Circuit ◽  
Chemical Vapor ◽  
High Growth ◽  
High Growth Rate ◽  
Open Circuit ◽  
Hot Wire ◽  
Microcrystalline Silicon

ABSTRACTWe report on ways to develop device quality microcrystalline silicon (μc-Si:H) intrinsic layer with high growth rate by hot-wire chemical vapor deposition (HWCVD). With combine approach of controlling impurities and moderate H-dilution [H2/SiH4 ͌ 2.5], we developed, for the first time, highly photosensitive (103 μc-Si:Hfilms with high growth rate (>1 nm/s); the microstructure of the film is found to be close to amorphous phase (fc ͌ 46 ̻± 5%). The photosensitivity systematically decreases with fc and saturates to 10 for fc> 70%. On application of these materials in non-optimized pin [.proportional]c-Si:H solar cell structure yields 700 mV open-circuit voltage however, surprisingly low fill factor and short circuit current. The importance of reduction of oxygen impurities [O], adequate passivation of grain boundary (GB) as well as presence of inactive GB of (220) orientation to achieve efficient [.proportional]c-Si:H solar cells are discussed.

Design and Numerical Simulation on the Optical and Electrical Behavior of a ZnO:Al Nanowire Array a-Si pin Solar Cell

2008 ◽  
Vol 1101 ◽  
Author(s):  
Chang-Wei Liu ◽  
Zingway Pei ◽  
Shu-Tong Chang ◽  
Ren-Yui Ho ◽  
Min-Wei Ho ◽  
...  
Keyword(s):  
Solar Cell ◽  
Carrier Transport ◽  
Fill Factor ◽  
Cell Structure ◽  
Short Circuit ◽  
Nanowire Array ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Si Solar Cell ◽  
Sun Light

AbstractOne of the parameters that limit the efficiency of a thin film solar cell, especially the a-Si and the nc-Si solar cell is the cell thickness. Although thicker film can absorb most of the sun light, the optical generated carriers will recombination through the numerous gap states in the film that obtained lower short circuit current and fill factor. In the controversy, thinner film could not absorb enough sun light that also limit the short circuit current. In this works, we utilize nanowire structure to solve the conflict between the light absorption and the carrier transport. The designed structure has ZnO:Al nanowire array on the substrate. The p-i-n a-Si solar cell structure is grown along the surface of each ZnO: Al nanowire sequentially. Under sunlight illumination, the light is absorbed in the axis direction of the nanowire. However, the carrier transport is along the radial direction of the solar cell. Therefore, the long nanowire could absorb most of the solar light. In the mean time, the thickness of the solar cell still is thin enough for photo-generated carrier transport. The dependence of short circuit current, open circuit voltage and fill factor to the length, diameter and density of ZnO:Al nanowires were simulated.

scholarly journals Pemanfaatan Zat Warna Alam Kayu Jambal (Pelthophorumferugineum) sebagai Sensitizer pada Sel Surya Fotoelektrokimia

ELKHA ◽  
2016 ◽  
Vol 8 (1) ◽  
Author(s):  
Syahrul Khairi
Keyword(s):  
Solar Cell ◽  
Thin Layer ◽  
Short Circuit ◽  
Dye Adsorption ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Measurement Results ◽  
Coating Method ◽  
Solid Liquid ◽  
Short Circuit Currents

Abstract– The Natural dye of Jambal wood (Pelthophorumferugineum) was used as sensitizer in the fabrication of dye sensitizer solar cell (DSSC). The dye was extracted by using solid-liquid extraction method with ethanol as a solvent. UV-Vis spectrophotometer was used to measure the absorbance of dye solution. TiO2 thin-layer was prepared by slip coating method which the pH 5 suspension of TiO2 Degussa on HCl deposited on a glass substrate Fluorine-doped Tin Oxide (FTO).Dye adsorption was done by the immersion TiO2 thin layer in the dye solution in ethanol for 24 hours after calcination, then used as the working electrode. Counter electrode was prepared by the deposition of gold on the glass substrate.The performance of solar cells sensitized of natural Jambal wood dye was investigated through the measurements of Isc (short circuit currents) and Voc (open circuit voltage on) during irradiation with sun simulated Philips Powertone lamp. The measurement results showed that the solar cell has Isc and Voc by 56 ηA/cm2 and 394 mV respectively.   Keywords– Fotoelektrokimia, Dye Sensitized Solar Cell, zatwarnaalam, Jambal.

scholarly journals Novel Photonic Crystal Based Polycrystalline CdTe/Silicon Solar Cells

2020 ◽  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Photonic Crystal ◽  
Conversion Efficiency ◽  
Current Density ◽  
Cell Structure ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Silicon Solar Cells

In this paper, a novel photonic crystal (PhC) polycrystalline CdTe/Silicon solar cells are theoretically explained that increase their short circuit current density and conversion efficiency. The proposed structure consist of a polycrystalline CdTe/Silicon solar cell that a photonic crystal is formed in the upper cell. The optical confinement is achieved by means of photonic crystal that can adjust the propagation and distribution of photons in solar cells. For validation of modeling, the electrical properties of the experimentally-fabricated based CdS/CdTe solar cell is modeled and compared that there is good agreement between the modeling results and experimental results from the litterature. The results of this study showed that the solar cell efficiency is increased by about 25% compared to the reference cell by using photonic crystal. The open circuit voltage, short circuit current density, fill factor and conversion efficiency of proposed solar cell structure are 1.01 V, 40.7 mA/cm2, 0.95 and 27% under global AM 1.5 conditions, respectively. Furthermore, the influence of carrier lifetime variation in the absorber layer of proposed solar cell on the electrical characteristics was theoretically considered and investigated.

scholarly journals Enhanced Efficiency of MAPbI3 Perovskite Solar Cells with FAPbX3 Perovskite Quantum Dots

Nanomaterials ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 121 ◽  
Author(s):  
Lung-Chien Chen ◽  
Ching-Ho Tien ◽  
Zong-Liang Tseng ◽  
Jun-Hao Ruan
Keyword(s):  
Quantum Dots ◽  
Solar Cells ◽  
Solar Cell ◽  
Cell Structure ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Hole Transport ◽  
Transport Layer ◽  
Electron Transport Layer ◽  
Perovskite Quantum Dots

We describe a method to enhance power conversion efficiency (PCE) of MAPbI3 perovskite solar cell by inserting a FAPbX3 perovskite quantum dots (QD-FAPbX3) layer. The MAPbI3 and QD-FAPbX3 layers were prepared using a simple, rapid spin-coating method in a nitrogen-filled glove box. The solar cell structure consists of ITO/PEDOT:PSS/MAPbI3/QD-FAPbX3/C60/Ag, where PEDOT:PSS, MAPbI3, QD-FAPbX3, and C60 were used as the hole transport layer, light-absorbing layer, absorption enhance layer, and electron transport layer, respectively. The MAPbI3/QD-FAPbX3 solar cells exhibit a PCE of 7.59%, an open circuit voltage (Voc) of 0.9 V, a short-circuit current density (Jsc) of 17.4 mA/cm2, and a fill factor (FF) of 48.6%, respectively.

Sign in / Sign up

Export Citation Format

Share Document