scholarly journals Some Studies on Prestressed Reinforced Granular Beds Overlying Weak Soil

2012 ◽  
Vol 2012 ◽  
pp. 1-13 ◽  
Author(s):  
J. Jayamohan ◽  
R. Shivashankar
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Experimental Results ◽  
Finite Element Analyses ◽  
Granular Bed ◽  
Weak Soil ◽  
Soil Thickness ◽  
Prestressing Force ◽  
Load Carrying ◽  
Good Agreement

This paper mainly investigates, from a series of laboratory scale bearing capacity tests carried out on a model square footing, the improvement in bearing capacity and reduction in settlement of a geonet reinforced granular bed (RGB) overlying weak soil due to prestressing the reinforcement. The parameters are the strength of the underlying weak soil, thickness of the granular bed, and magnitude and direction of prestressing force. The settlements at the interface are also measured. The addition of prestress to geonet reinforcement results in significant improvement in the load carrying capacity and settlement response of the prestressed geonet RGB. Improvement in bearing capacity is found to be more with biaxial prestressing than with uniaxial prestressing. Experimental results are also used to validate a proposed numerical model. The BCR (bearing capacity ratio) values predicted from this model are found to be in good agreement with the experimentally obtained BCR values. Finite element analyses are also carried out using the programme PLAXIS, to study the effect of prestressing the reinforcement. Results obtained from finite element analyses are also found to be in good agreement with the experimental results.

scholarly journals Load-carrying capacity of welded K-type joints inside floor truss systems

2019 ◽  
Vol 52 (1) ◽  
pp. 38-52
Author(s):  
Pooya Saremi ◽  
Wei Lu ◽  
Jari Puttonen ◽  
Dan Pada ◽  
Jyrki Kesti
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Carrying Capacity ◽  
Numerical Models ◽  
High Load ◽  
Load Carrying Capacity ◽  
Finite Element Analyses ◽  
Load Bearing Capacity ◽  
Load Carrying ◽  
Joint Behaviour

The load-carrying capacity of a K-type joint inside a floor truss is studied both experimentally and numerically. The joint tested is a scaled-down, isolated joint. The tubular braces, plate chord, and division plate are made of SSAB Domex steel. Comparison of load displacement curves received by finite element analyses with curves obtained from tests confirms that numerical models describe joint behaviour reasonable. The paper demonstrates that joints with high load-bearing capacity can be investigated experimentally by scaling the dimensions of the joint down when testing devices can affect the required capacity of the joint. The results presented can also be used for optimizing failure mechanism of similar joints in practice.

Nonlinear Numerical Analysis of SRC Frame Middle Joints

2013 ◽  
Vol 376 ◽  
pp. 231-235
Author(s):  
Cheng Li ◽  
Yun Zou ◽  
Jie Kong ◽  
Zhi Wei Wan
Keyword(s):  
Finite Element ◽  
Numerical Analysis ◽  
Bearing Capacity ◽  
Axial Load ◽  
Load Ratio ◽  
Experimental Results ◽  
Steel Ratio ◽  
Finite Element Software ◽  
Axial Load Ratio ◽  
Hysteretic Performance

Nonlinear numerical analysis for the force performance of frame middle joint is processed in this paper with the finite element software of ABAQUS. Compared with experimental results, numerical analysis results are found to be reasonable. Then the influence of factors such as shaped steel ratio and axial-load ratio are contrastively analyzed. The results show that shaped steel ratio has a greater influence on the bearing capacity and hysteretic performance of the structure, but the axial-load ratio has less influence.

Comparison of flexural capacity of different hollow slab beams with/without pavement layer reinforced by steel plates

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Long Liu ◽  
Lifeng Wang ◽  
Ziwang Xiao
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Steel Plate ◽  
Plate Thickness ◽  
Experimental Results ◽  
Nonlinear Material ◽  
Finite Element Models ◽  
Rc Beams ◽  
Flexural Capacity ◽  
Content Type

PurposeReinforcement of reinforced concrete (RC) beams in-service have always been an important research field, anchoring steel plate in the bottom of the beams is a kind of common reinforcement methods. In actual engineering, the contribution of pavement layer to the bearing capacity of RC beams is often ignored, which underestimates the bearing capacity and stiffness of RC beams to a certain extent. The purpose of this paper is to study the effect of pavement layer on the RC beams before and after reinforcement.Design/methodology/approachFirst, static load experiments are carried out on three in-service RC hollow slab beams, meanwhile, nonlinear finite element models are built to study the bearing capacity of them. The nonlinear material and shear slip effect of studs are considered in the models. Second, the finite element models are verified, and the numerical simulation results are in good agreement with the experimental results. Last, the finite element models are adopted to carry out the research on the influence of different steel plate thicknesses on the flexural bearing capacity and ductility.FindingsThe experimental results showed that pavement layers increase the flexural capacity of hollow slab beams by 16.7%, and contribute to increasing stiffness. Ductility ratio of SPRCB3 and PRCB2 was 30% and 24% lower than that of RCB1, respectively. The results showed that when the steel plate thickness was 1 mm–6 mm, the bearing capacity of the hollow slab beam increased gradually from 2158.0 kN.m to 2656.6 kN.m. As the steel plate thickness continuously increased to 8 mm, the ultimate bearing capacity increased to 2681.0 kN.m. The increased thickness did not cause difference to the bearing capacity, because of concrete crushing at the upper edge.Originality/valueIn this paper, based on the experimental study, the bearing capacity of hollow beam strengthened by steel plate with different thickness is extrapolated by finite element simulation, and its influence on ductility is discussed. This method not only guarantees the accuracy of the bearing capacity evaluation, but also does not require a large number of samples, and has certain economy. The research results provide a basis for the reinforcement design of similar bridges.

LOAD-CARRYING CAPACITIES FOR CIRCULAR METAL FOAM CORE SANDWICH PANELS AT LARGE DEFLECTION

2008 ◽  
Vol 22 (31n32) ◽  
pp. 6218-6223 ◽  
Author(s):  
W. HOU ◽  
Z. WANG ◽  
L. ZHAO ◽  
G. LU ◽  
D. SHU
Keyword(s):  
Finite Element ◽  
Velocity Field ◽  
Large Deflection ◽  
Metal Foam ◽  
Yield Criterion ◽  
Metallic Foam ◽  
Foam Core ◽  
Element Simulation ◽  
Load Carrying ◽  
Good Agreement

This paper is concerned with the load-carrying capacities of a circular sandwich panel with metallic foam core subjected to quasi-static pressure loading. The analysis is performed with a newly developed yield criterion for the sandwich cross section. The large deflection response is estimated by assuming a velocity field, which is defined based on the initial velocity field and the boundary condition. A finite element simulation has been performed to validate the analytical solution for the simply supported cases. Good agreement is found between the theoretical and finite element predictions for the load-deflection response.

Influence of backing materials towards the fatigue strength of butt-welded joints

2011 ◽  
Vol 225 (8) ◽  
pp. 1798-1807 ◽  
Author(s):  
M H Kim ◽  
H J Kim ◽  
J H Han ◽  
J M Lee ◽  
Y D Kim ◽  
...  
Keyword(s):  
Finite Element ◽  
Fatigue Strength ◽  
Welded Joints ◽  
Fatigue Tests ◽  
Experimental Results ◽  
Finite Element Analyses ◽  
Cold Metal Transfer ◽  
Notch Stress ◽  
Effective Notch Stress ◽  
Cold Metal

The purpose of this study is to investigate the fatigue strength of butt-welded joints with special attention paid to employing different kinds of backing plates. The effect of the under-matched weld was also considered. Four different cases of backing scenarios for butt-welded specimens such as steel backing, ceramic backing, CMT (no backing by cold metal transfer) and UM (under-matched welded specimen) were investigated. A series of fatigue tests was performed to compare the fatigue strength of butt-welded joints with respect to different backing scenarios. Effective notch stress was used for the interpretation of fatigue strength of butt-welded specimens with backing plates based on finite element analyses for calculating fatigue notch factors. When results were presented from the effective notch stress, all backing scenarios considered in this study exhibited the fatigue strengths corresponding to the FAT 225 curve. From the experimental results of this study, it was determined that the fatigue strengths of butt-welded joints were found to be in the order of CMT, ceramic backing, UM, and steel backing. No significant decrease in fatigue strength, however, was observed when backing plates were steel backing and ceramic backing types.

Experimental and numerical investigation on seismic performance of hollow floor interior slab-column connections

2020 ◽  
pp. 136943322096527
Author(s):  
Longji Dang ◽  
Rui Pang ◽  
Rui Liu ◽  
Hongmei Ni ◽  
Shuting Liang
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Seismic Performance ◽  
Seismic Behavior ◽  
Element Model ◽  
Experimental Results ◽  
Element Analysis ◽  
Skeleton Curve ◽  
The North ◽  
Parallel Tube

This paper aims to investigate the seismic performance of hollow floor interior slab-column connection (HFISC). In this new connection system, several tube fillers are placed in slab to form hollow concrete. Moreover, locally solid zone, shear components, and hidden beam around the connections are installed to improve the bearing capacity and ductility of specimens. Three slab-column connections with different shear components were tested under cyclic loading and every specimen was constructed with parallel tube fillers in the north direction and orthogonal tube fillers in the south direction. The seismic behavior of specimens was evaluated according to the hysteretic response, skeleton curve, ductility, stiffness degradation, and energy dissipation. A finite element model was then developed and validated by a comparison with the experimental results. Based on experimental results and finite element analysis results, the relative effects of the hollow ratio of slab, the ratio of longitudinal reinforcement, the shear area of bent-up steel bars, and the arm length of welding section steel cross bridging were elucidated through parametric studies. This new slab-column connection showed better plastic deformation capacity while the bearing capacity was kept. Specimens with parallel tube fillers showed better seismic behavior than those of specimens with orthogonal tube fillers.

Experimental and finite element study on the single-layer reticulated composite joints

2020 ◽  
Vol 23 (10) ◽  
pp. 2174-2187
Author(s):  
Liang Zheng ◽  
Cheng Qin ◽  
Hong Guo ◽  
Dapeng Zhang ◽  
Mingtan Zhou ◽  
...  
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Axial Compression ◽  
Wall Thickness ◽  
Great Influence ◽  
Single Layer ◽  
Experimental Results ◽  
Steel Pipe ◽  
Cover Plate ◽  
Element Analysis

In this article, a new type of reticulated joint, named the steel–concrete composite reticulated shell joint, is proposed. The proposed reticulated shell joint consists of an inner circular steel pipe, an outer circular steel pipe, a steel cover plate, and internal concrete. Five test specimens were tested under axial compression. The variable study included the wall thickness of the inner and outer circular steel pipes and the radius of the inner circular steel pipe. The test specimens exhibited a high bearing capacity and good plastic deformation ability under axial compression. The test results show that the wall thickness of the outer circular steel pipe and the radius of the inner circular steel pipe have a great influence on the bearing capacity of the steel–concrete composite reticulated shell joint, while the wall thickness of the inner circular steel pipe has little influence on the bearing capacity of the steel–concrete composite reticulated shell joint. Based on the test of the steel–concrete composite reticulated shell joints under axial load, the three-dimensional nonlinear finite element model was used to analyze the mechanical properties of the steel–concrete composite reticulated shell joints under axial compression. The results of the finite element analysis showed good agreement with the experimental results. The formula for calculating the bearing capacity of the joint is derived. By comparing with the experimental results, the calculated results are basically consistent with the experimental results.

Modelling the applied vertical stress and settlement relationship of shallow foundations in saturated and unsaturated sands

2011 ◽  
Vol 48 (3) ◽  
pp. 425-438 ◽  
Author(s):  
Won Taek Oh ◽  
Sai K. Vanapalli
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Characteristic Curve ◽  
Friction Angle ◽  
Vertical Stress ◽  
Shallow Foundations ◽  
Surface Settlement ◽  
Soil Parameters ◽  
Finite Element Analyses ◽  
Unsaturated Sands

The bearing capacity and settlement of foundations are determined experimentally or modelled numerically based on conventional soil mechanics for saturated soils. In both methods, bearing capacity and settlement are estimated based on the applied vertical stress versus surface settlement relationship. These methods are also conventionally used for soils that are in an unsaturated condition, ignoring the contribution of matric suction. In this study, a methodology is proposed to estimate the bearing capacity and settlement of shallow foundations in unsaturated sands by predicting the applied vertical stress versus surface settlement relationship. The proposed method requires soil parameters obtained under only saturated conditions (i.e., effective cohesion, effective internal friction angle, and modulus of subgrade reaction from model footing test) along with the soil-water characteristic curve (SWCC). In addition, finite element analyses are undertaken to simulate the applied vertical stress versus surface settlement relationship for unsaturated sands. The proposed method and finite element analyses are performed using an elastic – perfectly plastic model. The predicted bearing capacities and settlements from the proposed method and finite element analyses are compared with published model footing test results. There is good agreement between measured and predicted results.

scholarly journals Qualitative Research of AZ31 Magnesium Alloy Aircraft Brackets Produced by a New Forging Method

2016 ◽  
Vol 61 (2) ◽  
pp. 1003-1008 ◽  
Author(s):  
A. Dziubińska ◽  
A. Gontarz ◽  
K. Dziedzic
Keyword(s):  
Qualitative Research ◽  
Finite Element ◽  
Magnesium Alloy ◽  
Numerical Results ◽  
Experimental Results ◽  
Az31 Magnesium Alloy ◽  
Forming Process ◽  
Closed Die Forging ◽  
Selection Of ◽  
Good Agreement

AbstractThe paper reports a selection of numerical and experimental results of a new closed-die forging method for producing AZ31 magnesium alloy aircraft brackets with one rib. The numerical modelling of the new forming process was performed by the finite element method.The distributions of stresses, strains, temperature and forces were examined. The numerical results confirmed that the forgings produced by the new forming method are correct. For this reason, the new forming process was verified experimentally. The experimental results showed good agreement with the numerical results. The produced forgings of AZ31 magnesium alloy aircraft brackets with one rib were then subjected to qualitative tests.

Sign in / Sign up

Export Citation Format

Share Document