scholarly journals EVOLUÇÃO DA INFESTAÇÃO POR Sirex noctilio EM FUNÇÃO DA DISTRIBUIÇÃO DIAMÉTRICA EM PLANTIOS DE Pinus taeda

FLORESTA ◽  
2003 ◽  
Vol 33 (1) ◽  
Author(s):  
Débora Cristina Machado Gaiad ◽  
Afonso Figueiredo Filho ◽  
Edilson Batista De Oliveira ◽  
Susete do Rocio Chiarello Penteado
Keyword(s):  
Pinus Taeda ◽  
Health Condition ◽  
Management Program ◽  
Diameter Distribution ◽  
Forest Research ◽  
Sirex Noctilio ◽  
Additional Measure ◽  
Before And After ◽  
Thinning Operations ◽  
Set Up

Este trabalho teve como objetivo analisar a evolução do ataque de Sirex noctilio (vespa-da-madeira), em função da distribuição diamétrica em plantios de Pinus taeda desbastados e não desbastados. Os dados utilizados no estudo foram provenientes de um experimento com cinco tratamentos e cinco repetições, instalado em três áreas da empresa Klabin-Celucat no estado de Santa Catarina, em parceria com a Embrapa Florestas. Os tratamentos foram aplicados em sub-áreas de 3600 m2 com parcelas amostrais de 400 m2 (20 x 20 m) instaladas no centro de cada sub-área. O delineamento experimental usado foi blocos ao acaso. Foram testados os seguintes tratamentos: (a) T1 - testemunha (sem desbaste); (b) T2 - 25% (4a linha) desbaste sistemático e 10% seletivo nas remanescentes; (c) T3 - 25% sistemático e 20% seletivo; (d) T4 - 25% sistemático e 30% seletivo; (e) T5 - 25% sistemático e 40% seletivo. No desbaste seletivo foram retiradas, preferencialmente, as árvores atacadas, bifurcadas e dominadas. Foram coletadas informações sobre DAP (diâmetro à altura do peito), h (altura total) e condição fitossanitária (sadia ou atacada) das árvores de cada parcela, antes e depois da aplicação de cada tratamento a fim de relacionar a infestação da vespa-da-madeira com o vigor das árvores. Neste estudo concluiu-se que: (a) o desbaste retarda o ritmo de ataque da vespa-da-madeira e pode ser utilizado como medida adicional de controle em um programa de manejo integrado de pragas; (b) o ataque da vespa-da-madeira inicia-se pelas árvores de menor diâmetro e atinge as de maior diâmetro com o aumento da infestação, ocorrendo um deslocamento ascendente no pico de ataque das classes de menor para as de maior diâmetro. EVOLUTION OF Sirex noctilio INFESTATION IN REALTION TO DIAMETER DISTRIBUTION ON Pinus taeda Abstract This paper aimed to analyze the evolution of Sirex noctilio (woodwasps) attack in relation to diameter distribution in thinned and unthinned Pinus taeda stands. The data were collected at Klabin-Celucat Company on a partnership with the National Center of Forest Research from Embrapa. The treatments were set up at 3600 m2 sub-plots with a 400 m2 (20 x 20) sampling area at the center of each sub-plot. The experimental design was randomized blocks. The following treatments were tested: (a) T1 - control (no thinning); (b) T2 - 25% systematic thinning followed by a 10% selective thinning; (c) T3 - 25% systematic thinning followed by a 20% selective thinning; (d) T4 - 25% systematic thinning followed by a 30% selective thinning; T5 - 25% systematic thinning followed by a 40% selective thinning. At the selective thinning were withdraw the attacked, forked and dominated trees. It were taken data on DBH (diameter at breast height), h (total height) and health condition (attacked or not attacked) of trees before and after the treatments implantation, aiming to establish relationship between the woodwasp infestation and tree vigor. It was concluded that: (a) thinning operations delay the rhythm of woodwasp attack and can be used as additional measure of control on an integrated pest management program; (b) the woodwasp attack starts by the trees with smaller diameters and reach the trees with bigger diameter as the infestation rises moving up the peak of attack from smaller classes of diameter towards the higher classes.

Improving radiotherapy safety and efficiency with the customized ARIA oncology information system

2021 ◽  
pp. 1-10
Author(s):  
Zhongfei Wang ◽  
Qinghui Yun ◽  
Changhao Liua ◽  
Xiaohuan Sun ◽  
Wei Wang ◽  
...  
Keyword(s):  
Information System ◽  
Treatment Planning ◽  
Process Management ◽  
Treatment Process ◽  
Management Program ◽  
Completion Rate ◽  
Planning Time ◽  
Before And After ◽  
Set Up ◽  
Care Path

OBJECTIVE: To improve safety and efficiency of radiotherapy process by customizing a Varian ARIA oncology information system following the guidelines provided in AAPM TG-100 report. METHODS: First, failure mode and effects analysis (FMEA) and quality management program were implemented for radiotherapy process. We have customized the visual care path in the ARIA system and set up a series of templates for simulation, prescription, contouring, treatment planning, and multiple checklists. Average time of activities’ completion and amount of planning errors were compared before and after the use of the customized ARIA to evaluate its impact on the efficiency and safety of radiotherapy. RESULTS: Completion time and on-time completion rate of the key activities in the care path are improved. The time of OAR/targets contouring decreases from (1.94±1.51) days to (1.64±1.07) days (p = 0.003), with the on-time completion rate increases from 77.4%to 83.3%(p = 0.048). Treatment planning time decreases from (0.81±0.65) days to (0.55±0.51) days (p <  0.001), with the on-time completion rate increases from 96.6%to 98.3%(p = 0.163). Waiting time of patients decreases from (4.50±1.83) days to (4.04±1.34) days (p <  0.001), with the on-time completion rate increases from 81.9%to 89.7%(p = 0.003). In addition, the average plan error rate decreases from 5.5%(2.9%for safety errors and 2.6%for non-normative errors) to 2.4%(1.6%for safety errors and 0.8%for non-normative errors) (p = 0.029). CONCLUSION: Our study demonstrates that the customized ARIA system has the potential to promote efficiency and safety in radiotherapy process management. It is beneficial to organize and accelerate the treatment process with more effective communications and fewer errors.

Evaluation of Freezing Methods by Low Temperature X-Ray Diffraction

1977 ◽  
Vol 35 ◽  
pp. 330-333
Author(s):  
T. Gulik-Krzywicki ◽  
M.J. Costello
Keyword(s):  
Biological Materials ◽  
Molecular Organization ◽  
X Ray Diffraction ◽  
Glass Capillary ◽  
X Ray ◽  
Rate Dependent ◽  
Before And After ◽  
Freeze Etching ◽  
Diffraction Patterns ◽  
Set Up

Freeze-etching electron microscopy is currently one of the best methods for studying molecular organization of biological materials. Its application, however, is still limited by our imprecise knowledge about the perturbations of the original organization which may occur during quenching and fracturing of the samples and during the replication of fractured surfaces. Although it is well known that the preservation of the molecular organization of biological materials is critically dependent on the rate of freezing of the samples, little information is presently available concerning the nature and the extent of freezing-rate dependent perturbations of the original organizations. In order to obtain this information, we have developed a method based on the comparison of x-ray diffraction patterns of samples before and after freezing, prior to fracturing and replication.Our experimental set-up is shown in Fig. 1. The sample to be quenched is placed on its holder which is then mounted on a small metal holder (O) fixed on a glass capillary (p), whose position is controlled by a micromanipulator.

scholarly journals Cardiac Rehabilitation and Physical Performance in Patients after Myocardial Infarction: Preliminary Research

2021 ◽  
Vol 10 (11) ◽  
pp. 2253
Author(s):  
Agnieszka Grochulska ◽  
Sebastian Glowinski ◽  
Aleksandra Bryndal
Keyword(s):  
Myocardial Infarction ◽  
Cardiac Rehabilitation ◽  
Physical Performance ◽  
Stress Test ◽  
Maximal Oxygen Consumption ◽  
Exercise Stress Test ◽  
Health Condition ◽  
Exercise Stress ◽  
Test Time ◽  
Before And After

(1) Background: Cardiovascular diseases, in particular, myocardial infarction (MI), are the main threats to human health in modern times. Cardiac rehabilitation (CR), and especially increased physical activity, significantly prevent the consequences of MI. The aim of this study was to assess physical performance in patients after MI before and after CR. (2) Methods: 126 patients after MI were examined. They were admitted to the cardiac rehabilitation ward twice: in the 3rd month after MI, and then in the 6th month after the last rehabilitation session. CR lasted 20 treatment days (4 weeks with 5 treatment days and 2 days’ break). The exercise stress test on the treadmill and a 6-minute walk test (6MWT) were used to assess physical performance. Patients were assigned to an appropriate rehabilitation model due to their health condition. (3) Results: In the studied group, the exercise stress test time and the metabolic equivalent of task (MET), the maximal oxygen consumption (VO2max), and 6MWT score increased significantly (p = 0.0001) at two time-points of observation. (4) Conclusion: CR significantly improves physical performance in patients after MI.

Research on pull-type multi-AGV system dynamic path optimization based on time window

2021 ◽  
pp. 095440702098271
Author(s):  
Hongying Shan ◽  
Chuang Wang ◽  
Cungang Zou ◽  
Mengyao Qin
Keyword(s):  
Path Planning ◽  
Time Window ◽  
Planning Problem ◽  
Dijkstra Algorithm ◽  
Before And After ◽  
Common Planning ◽  
Planning Algorithm ◽  
Dynamic Path ◽  
Set Up ◽  
Path Planning Algorithm

This paper is a study of the dynamic path planning problem of the pull-type multiple Automated Guided Vehicle (multi-AGV) complex system. First, based on research status at home and abroad, the conflict types, common planning algorithms, and task scheduling methods of different AGV complex systems are compared and analyzed. After comparing the different algorithms, the Dijkstra algorithm was selected as the path planning algorithm. Secondly, a mathematical model is set up for the shortest path of the total driving path, and a general algorithm for multi-AGV collision-free path planning based on a time window is proposed. After a thorough study of the shortcomings of traditional single-car planning and conflict resolution algorithms, a time window improvement algorithm for the planning path and the solution of the path conflict covariance is established. Experiments on VC++ software showed that the improved algorithm reduces the time of path planning and improves the punctual delivery rate of tasks. Finally, the algorithm is applied to material distribution in the OSIS workshop of a C enterprise company. It can be determined that the method is feasible in the actual production and has a certain application value by the improvement of the data before and after the comparison.

scholarly journals Wear and Friction Characteristics of 65Mn Steel for Spike-Tooth Harrow

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 319
Author(s):  
Zhiguo Lu ◽  
Chuanyu Du ◽  
Qingcai Chen ◽  
Tianying Niu ◽  
Na Wang ◽  
...  
Keyword(s):  
Friction And Wear ◽  
Working Environment ◽  
Manganese Steel ◽  
Wear Loss ◽  
Variable Parameters ◽  
Wear Characteristics ◽  
Before And After ◽  
Set Up ◽  
Worn Surface ◽  
Friction And Wear Characteristics

The friction and wear characteristics of spike-tooth material (65Mn steel) of Spike-Tooth Harrow in a two-stage peanut harvester were studied in this paper. The friction and wear tests of pin and disc on 65 manganese steel were carried out on the tribometer, then the wear loss and the friction coefficient were studied. The wear loss of the pin was acquired by calculating the mass of the pin before and after the experiment using an electronic balance. According to the actual working environment of peanut spring-finger, four variable parameters are set up: load, speed, soil moisture and soil type. The friction and wear characteristics of pins were studied under different loads, speeds and different soil environments. After wearing, the worn surface of the material was observed by scanning microscope and the wear mechanism was studied. The experimental results show that the wear of the pin increases with the increase of load and decreases with the increase of rotational speed in the same rotation number. Especially in the case of the sandy soil with 20% in moisture, a maximum wear loss of the pin is achieved.

scholarly journals Innovative passive reinforcements for the gradual stabilization of a landslide according with the observational method

Landslides ◽  
2021 ◽  
Author(s):  
Lorenzo Brezzi ◽  
Alberto Bisson ◽  
Davide Pasa ◽  
Simonetta Cola
Keyword(s):  
Monitoring System ◽  
Low Cost ◽  
Economic Losses ◽  
Fe Model ◽  
Site Conditions ◽  
Observational Method ◽  
Rainy Period ◽  
Sustainable Solutions ◽  
Before And After ◽  
Set Up

AbstractA large number of landslides occur in North-Eastern Italy during every rainy period due to the particular hydrogeological conditions of this area. Even if there are no casualties, the economic losses are often significant, and municipalities frequently do not have sufficient financial resources to repair the damage and stabilize all the unstable slopes. In this regard, the research for more economically sustainable solutions is a crucial challenge. Floating composite anchors are an innovative and low-cost technique set up for slope stabilization: it consists in the use of passive sub-horizontal reinforcements, obtained by coupling a traditional self-drilling bar with some tendons cemented inside it. This work concerns the application of this technique according to the observational method described within the Italian and European technical codes and mainly recommended for the design of geotechnical works, especially when performed in highly uncertain site conditions. The observational method prescribes designing an intervention and, at the same time, using a monitoring system in order to correct and adapt the project during realization of the works on the basis of new data acquired while on site. The case study is the landslide of Cischele, a medium landslide which occurred in 2010 after an exceptional heavy rainy period. In 2015, some floating composite anchors were installed to slow down the movement, even if, due to a limited budget, they were not enough to ensure the complete stabilization of the slope. Thanks to a monitoring system installed in the meantime, it is now possible to have a comparison between the site conditions before and after the intervention. This allows the evaluation of benefits achieved with the reinforcements and, at the same time, the assessment of additional improvements. Two stabilization scenarios are studied through an FE model: the first includes the stabilization system built in 2015, while the second evaluates a new solution proposed to further increase the slope stability.

scholarly journals Assessing baseline dependency of anchor-based minimal important change (MIC): don’t stratify on the baseline score!

2021 ◽  
Author(s):  
Berend Terluin ◽  
Ewa M. Roos ◽  
Caroline B. Terwee ◽  
Jonas B. Thorlund ◽  
Lina H. Ingelsrud
Keyword(s):  
Real Data ◽  
Patient Reported Outcome ◽  
Health Condition ◽  
Important Change ◽  
Alternative Methods ◽  
Minimal Important Change ◽  
Baseline Score ◽  
Patient Reported ◽  
Before And After ◽  
Parallel Tests

Abstract Purpose The minimal important change (MIC) of a patient-reported outcome measure (PROM) is often suspected to be baseline dependent, typically in the sense that patients who are in a poorer baseline health condition need greater improvement to qualify as minimally important. Testing MIC baseline dependency is commonly performed by creating two or more subgroups, stratified on the baseline PROM score. This study’s purpose was to show that this practice produces biased subgroup MIC estimates resulting in spurious MIC baseline dependency, and to develop alternative methods to evaluate MIC baseline dependency. Methods Datasets with PROM baseline and follow-up scores and transition ratings were simulated with and without MIC baseline dependency. Mean change MICs, ROC-based MICs, predictive MICs, and adjusted MICs were estimated before and after stratification on the baseline score. Three alternative methods were developed and evaluated. The methods were applied in a real data example for illustration. Results Baseline stratification resulted in biased subgroup MIC estimates and the false impression of MIC baseline dependency, due to redistribution of measurement error. Two of the alternative methods require a second baseline measurement with the same PROM or another correlated PROM. The third method involves the construction of two parallel tests based on splitting the PROM’s item set. Two methods could be applied to the real data. Conclusion MIC baseline dependency should not be tested in subgroups based on stratification on the baseline PROM score. Instead, one or more of the suggested alternative methods should be used.

Reducing Culture Reporting Errors in the Microbiology Laboratory

2019 ◽  
Vol 152 (Supplement_1) ◽  
pp. S131-S132
Author(s):  
Kathryn Hogan ◽  
Beena Umar ◽  
Mohamed Alhamar ◽  
Kathleen Callahan ◽  
Linoj Samuel
Keyword(s):  
Real Time ◽  
Error Rate ◽  
Reporting System ◽  
Error Rates ◽  
Tracking Errors ◽  
Corrective Measures ◽  
Safety Awareness ◽  
Before And After ◽  
Set Up ◽  
System Errors

Abstract Objectives There are few papers that characterize types of errors in microbiology laboratories and scant research demonstrating the effects of interventions on microbiology lab errors. This study aims to categorize types of culture reporting errors found in microbiology labs and to document the error rates before and after interventions designed to reduce errors and improve overall laboratory quality. Methods To improve documentation of error incidence, a self-reporting system was changed to an automatic reporting system. Errors were categorized into five types Gram stain (misinterpretations), identification (incorrect analysis), set up labeling (incorrect patient labels), procedures (not followed), and miscellaneous. Error rates were tracked according to technologist, and technologists were given real-time feedback by a manager. Error rates were also monitored in the daily quality meeting and frequently detected errors were discussed at staff meetings. Technologists attended a year-end review with a manager to improve their performance. To maintain these changes, policies were developed to monitor technologist error rate and to define corrective measures. If a certain number of errors per month was reached, technologists were required to undergo retraining by a manager. If a technologist failed to correct any error according to protocol, they were also potentially subject to corrective measures. Results In 2013, we recorded 0.5 errors per 1,000 tests. By 2018, we recorded only 0.1 errors per 1,000 tests, an 80% decrease. The yearly culture volume from 2013 to 2018 increased by 32%, while the yearly error rate went from 0.05% per year to 0.01% per year, a statistically significant decrease (P = .0007). Conclusion This study supports the effectiveness of the changes implemented to decrease errors in culture reporting. By tracking errors in real time and using a standardized process that involved timely follow-up, technologists were educated on error prevention. This practice increased safety awareness in our micro lab.

Frey's syndrome: treatment with botulinum toxin

1997 ◽  
Vol 111 (9) ◽  
pp. 839-844 ◽  
Author(s):  
A. Bjerkhoel ◽  
O. Trobbe
Keyword(s):  
Botulinum Toxin ◽  
Botulinum Toxin A ◽  
Surgical Techniques ◽  
Frey’S Syndrome ◽  
Need For Treatment ◽  
Gustatory Sweating ◽  
Parotid Surgery ◽  
Frey's Syndrome ◽  
Before And After ◽  
Set Up

AbstractFrey's syndrome, i.e. gustatory sweating on the cheek, is a fairly common embarrassment after parotid gland surgery. New surgical techniques have been proposed to avoid this complication, but are not widely in use. Hence, there is need for treatment of Frey's syndrome. All surgical and topical treatments have drawbacks. This study was set up in order to evaluate a recently described treatment. One hundred and two patients were interviewed after parotidectomy. Thirty-one of them had noticed gustatory sweating and 15 patients underwent Minor's starch iodine test before, and after, treatment with intracutaneous injections of botulinum toxin A (Botox®, Allergan Inc., USA). Thirteen of the patients did not experience any gustatory sweating at follow-up (one to 13 months). Minor's starch test showed total disappearance of gustatory sweating in 12 of the 15 treated patients. The only side effect was a discreet, transitory affection of the orbicularis oris muscle in one patient. As this treatment is minimally invasive it could be an attractive treatment for Frey's syndrome if the effect is maintained. Complaints of local hypoaesthesia and pain were also common after parotid surgery.

Satisfaction of Postoperative Patients on Pain Management Program its Relationship to the Knowledge and Attitudes of Chinese Nurses: A Cross-Sectional Survey

2021 ◽  
Vol 7 (6) ◽  
pp. 6609-6626
Author(s):  
Shuyuan Li
Keyword(s):  
Pain Management ◽  
Optimal Level ◽  
Management Program ◽  
Chinese Patients ◽  
Cross Sectional Survey ◽  
Cross Sectional ◽  
Knowledge And Attitudes ◽  
Pain Management Program ◽  
Before And After ◽  
Knowledge And Attitude

This study is a cross-sectional survey of the satisfaction of postoperative patients its relationship to the knowledge and attitudes of Chinese nurses on pain management. Data were sourced out from two groups of respondents participated in the study, 75 post-operative patients and 97 in-service nurses from the health institutions China. The study was conducted for five-months. Ethics protocols were observed before and after the conduct of the study. Findings showed that post-operative pain management program among the participating medical institutions in China were assessed to have moderate level of satiation by the patients. All the components namely pain relief experience, care provided by the nurses, education provided as to pain management, and therapeutic dialogue provided by the nurses were all assessed by postoperative Chinese patients at a fair level. Meanwhile, gender and education of post-operative patients can be considered as factors in the planning and implementation of pain management program. Consequently, similar to studies conducted worldwide, Chinese nurses do not establish yet an optimal level of knowledge and attitude towards pain management. Meanwhile age, experience, education are factors on the knowledge and attitude on pain management among nurses. Finally, positive moderate relationship is established between patient satisfaction and knowledge and attitudes of nursing staff towards pain management. The findings of these study call for action and reform in the implementation of pain management program focusing on the major role and development of 21st century nurses. Practical implications of the study are discussed.

Sign in / Sign up

Export Citation Format

Share Document