scholarly journals Influence of Low Temperature Annealing in Uniaxial Mechanical Properties of Cold Rolled Stainless Steel Strip for Springs

2020 ◽  
Vol 2020 (65) ◽  
pp. 7-14
Author(s):  
Takayuki KOIZUMI
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Low Temperature ◽  
Steel Strip ◽  
Low Temperature Annealing ◽  
Cold Rolled

scholarly journals Effects of equal channel angular pressing and heat treatments on the microstructures and mechanical properties of selective laser melted and cast AlSi10Mg alloys

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Przemysław Snopiński ◽  
Mariusz Król ◽  
Marek Pagáč ◽  
Jana Petrů ◽  
Jiří Hajnyš ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Equal Channel Angular Pressing ◽  
Heat Treatments ◽  
Electron Backscattered Diffraction ◽  
Angular Pressing ◽  
Low Temperature Annealing ◽  
Transmission Electron ◽  
Before And After ◽  
The Impact

AbstractThis study investigated the impact of the equal channel angular pressing (ECAP) combined with heat treatments on the microstructure and mechanical properties of AlSi10Mg alloys fabricated via selective laser melting (SLM) and gravity casting. Special attention was directed towards determining the effect of post-fabrication heat treatments on the microstructural evolution of AlSi10Mg alloy fabricated using two different routes. Three initial alloy conditions were considered prior to ECAP deformation: (1) as-cast in solution treated (T4) condition, (2) SLM in T4 condition, (3) SLM subjected to low-temperature annealing. Light microscopy, transmission electron microscopy, X-ray diffraction line broadening analysis, and electron backscattered diffraction analysis were used to characterize the microstructures before and after ECAP. The results indicated that SLM followed by low-temperature annealing led to superior mechanical properties, relative to the two other conditions. Microscopic analyses revealed that the partial-cellular structure contributed to strong work hardening. This behavior enhanced the material’s strength because of the enhanced accumulation of geometrically necessary dislocations during ECAP deformation.

Influence of Al-Cu-Mn-Fe-Ti Alloy Composition and Production Parameters of Extruded Semi-Finished Products on their Structure and Mechanical Properties

2017 ◽  
Vol 265 ◽  
pp. 456-462 ◽  
Author(s):  
P.L. Reznik ◽  
Mikhail Lobanov
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Thermal Treatment ◽  
Low Temperature ◽  
Room Temperature ◽  
High Temperature Strength ◽  
Ti Alloy ◽  
Low Temperature Annealing ◽  
Annealing Conditions ◽  
Concentration Changes

Studies have been conducted as to the effect of Cu, Mn, Fe concentration changes in Al-Cu-Mn-Fe-Ti alloy, the conditions of thermal and deformational treatment of ingots and extruded rods 40 mm in diameter on the microstructure, phase composition and mechanical properties. It has been determined that changing Al-6.3Cu-0.3Mn-0.17Fe-0.15Ti alloy to Al-6.5Cu-0.7Mn-0.11Fe-0.15Ti causes an increase in the strength characteristics of extruded rods at the room temperature both after molding and in tempered and aged conditions, irrespective of the conditions of thermal treatment of the initial ingot (low-temperature annealing 420 °С for 2 h, or high-temperature annealing at 530 °С for 12 h). Increasing the extruding temperature from 330 to 480 °С, along with increasing Cu, Mn and decreasing Fe in the alloy Al-Cu-Mn-Ti, is accompanied by the increased level of ultimate strength in a quenched condition by 25% to 410 MPa, irrespective of the annealing conditions of the original ingot. An opportunity to apply the Al-6.3Cu-0.3Mn-0.17Fe-0.15Ti alloy with low-temperature annealing at 420 °С for 2 h and the molding temperature of 330 °С has been found to produce rods where, in the condition of full thermal treatment (tempering at 535 °С + aging at 200 °С for 8 hours), a structure is formed that ensures satisfactory characteristics of high temperature strength by resisting to fracture for more than 100 hours at 300 °С and 70 MPa.

An Experimental Investigation of Surface Pit Evolution During Cold-Rolling or Drawing of Stainless Steel Strip

2000 ◽  
Vol 123 (1) ◽  
pp. 1-7 ◽  
Author(s):  
R. Ahmed ◽  
M. P. F. Sutcliffe
Keyword(s):  
Experimental Investigation ◽  
Stainless Steel ◽  
Hydrodynamic Lubrication ◽  
Steel Strip ◽  
Similar Rate ◽  
Steel Strips ◽  
Strip Drawing ◽  
Hot Band ◽  
Cold Rolled

This paper presents an experimental investigation of the mechanisms of pit elimination in strip drawing and rolling of stainless steel strips. Strip drawing tests with artificial indents confirm the role of micro-plasto-hydrodynamic lubrication (MPHL) in allowing pits to be reduced in size and depth. The similarity of results for two oils, which differ in viscosity by a factor of 10, is attributed to the fact that oil is drawn out of the pits rather easily, so that the behavior tends to the unlubricated case. Similar behavior is observed for strip drawing of shot blast white hot band. For much smoother bright anneal strip, it is suggested that the presence of an oil film in the unpitted region prevents generation of pressure differences between the pits and the unpitted regions. A comparison of strip-drawn and cold-rolled stainless steel samples show that the change in pit area and Rq roughness varies with overall reduction in a remarkably similar way. The reason for such similar behavior is attributed to the absence of hydrodynamic action in preventing pit elimination, albeit for opposite reasons. The similar rate of pit evolution in both cases confirms the usefulness of the strip drawing rig as a tool to model the change of surface topography during rolling, as long as care is taken in matching the regimes of lubrication.

Sign in / Sign up

Export Citation Format

Share Document