scholarly journals Localized damage analysis for high strength S960 steel using micro-tensile testing and digital image correlation

2018 ◽  
Vol 1 (S1) ◽  
pp. 16
Author(s):  
R.G. Dowding ◽  
C. Pinna ◽  
H. Ghadbeigi ◽  
D. Farrugia
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
Tensile Testing ◽  
High Strength ◽  
Image Correlation ◽  
Damage Analysis ◽  
Localized Damage

Cross Weld Tensile Testing With Digital Image Correlation to Determine Local Strain Response

2021 ◽  
Author(s):  
William Siefert ◽  
James Rule ◽  
Boian Alexandrov ◽  
Jorge Penso ◽  
Michael P. Buehner
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
Tensile Testing ◽  
Local Strain ◽  
Image Correlation ◽  
Strain Response

Study on Lüders Deformation in Welded Mild Steel Using Infrared Thermography and Digital Image Correlation

2012 ◽  
Vol 585 ◽  
pp. 82-86 ◽  
Author(s):  
N. Srinivasan ◽  
N. Raghu ◽  
B. Venkatraman
Keyword(s):  
Digital Image Correlation ◽  
Mild Steel ◽  
Infrared Thermography ◽  
Digital Image ◽  
Tensile Testing ◽  
Image Correlation ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Testing ◽  
Heterogeneous Deformation ◽  
Lüders Band

Studies on characterizing heterogeneous deformations in many materials under different loading conditions using imaging NDE techniques like Infrared thermography (IRT) and Digital image correlation (DIC) began in the last decade and have been reported by many researchers. This work aims in experimental investigation of one such heterogeneous deformation namely Lüders band phenomenon in welded IS 2062 E250-B mild steel during monotonic, uniaxial tensile testing using IRT and DIC. Also attempt has been made to study the generation of pre-yield microstrain in welded material. An understanding of nucleation and propagation of Lüders band in welded specimen is made based on temperature and strain changes.

Identification of the Mechanical Properties of High-Strength Steel Using Digital Image Correlation

2014 ◽  
Vol 980 ◽  
pp. 122-126 ◽  
Author(s):  
Michaela Štamborská ◽  
Miroslav Kvíčala ◽  
Monika Losertová
Keyword(s):  
Mechanical Properties ◽  
Digital Image Correlation ◽  
Digital Image ◽  
High Strength Steel ◽  
Strain Field ◽  
High Strength ◽  
Image Correlation ◽  
Uniaxial Tensile ◽  
Large Strains ◽  
Identification Procedure

Identification of the mechanical properties of high-strength steel using digital image correlation. In this paper an experimental procedure to identify the plastic behaviour of sheet metals up to large strains using full field measurement is presented. The tests were conducted on notched specimens. This geometry generates a heterogeneous strain field which was measured during the test using a digital image correlation system. The advantage of using a heterogeneous strain field in the identification procedure is that a complex state of stress-strain can be analyzed at the same time and much more information can be obtained in a single test. On the other hand, the stress field cannot be directly computed from the test and a suitable identification procedure must be developed. Here, the virtual fields method (VFM) adapted for large strains and plasticity was used to identify the hardening behaviour and the anisotropy of the material. The values obtained with the VFM were compared with the results from a standard identification made using uniaxial tensile tests.

scholarly journals Characterisation of weld heterogeneity through hardness mapping and miniature tensile testing

2015 ◽  
Vol 6 (3) ◽  
pp. 8 ◽  
Author(s):  
Jonas Bally ◽  
Wim De Waele ◽  
Patricia Verleysen ◽  
Nenad Gubeljak ◽  
Stijn Hertelé
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
Tensile Testing ◽  
Industrial Process ◽  
Tensile Tests ◽  
Image Correlation ◽  
Heterogeneous Microstructure ◽  
Fusion Weld

Welding is a widely adopted industrial process used for joining components. A fusion weld has a highly heterogeneous microstructure and characterisation of strength heterogeneity is difficult because of the potentially large variations over a limited distance. Hardness mapping and miniature tensile tests are two distinct approaches to this problem. This paper reports on the possibilities and limitations of both techniques. Hardness mapping is a well-documented procedure as opposed to miniature tensile testing, where the dimensions of the dogbone shaped specimens are smaller than what standards prescribe. A particular challenge is the measurement of strains in such small specimens. The authors have achieved this measurement by means of Digital Image Correlation (DIC). To that end, a sufficiently fine speckling method has been developed.

Application of 3D digital image correlation for the measurement of the tensile mechanical properties of high-strength steel

2021 ◽  
Vol 63 (4) ◽  
pp. 303-310
Author(s):  
Feipeng Zhu ◽  
Xiaoxia Gu ◽  
Pengxiang Bai ◽  
Dong Lei
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Digital Image Correlation ◽  
Yield Strength ◽  
Digital Image ◽  
High Strength Steel ◽  
High Strength ◽  
Experimental Results ◽  
Image Correlation ◽  
3D Digital Image Correlation

Abstract High-strength steel plays an important role in engineering fields such as infrastructure. For this reason, an accurate determination of its mechanical properties is of critical importance. Considering the inconvenience of conventional mechanical extensometers for the deformation measurement of small-scale specimens, 3D digital image correlation (3D-DIC) was used to measure the deformation of Grade 8.8 bolts and Q690 high-strength steel specimens by means of a uniaxial tensile test, and in this way, stress–strain curves, elastic modulus, yield strength, tensile strength, percentage elongation after fracture, and percentage reduction of area were obtained. Experimental results show that Grade 8.8 bolts and Q690 steel result in higher yield strength and tensile strength than common steel. Moreover, owing to the phenomenon that stress remains constant with strain increase in the yielding stage, the evolution process from elastic deformation to plastic deformation of the specimens during the yielding stage could be studied. Experimental results show that the axial strain of Grade 8.8 bolts increases from 0.3 to 1 % during the yielding stage and for Q690 specimens the corresponding strain increases from 0.4 to 1.8 %.

Sign in / Sign up

Export Citation Format

Share Document