scholarly journals Effects of temperature and time of thermal modification on density and colour of Pinus insularis and Dacrycarpus imbricatus wood

2020 ◽  
Vol 19 (05) ◽  
pp. 35-45
Author(s):  
Hoa V. Hoang

The Pinus kesiya and Podocarp (Dacrycarpus imbricatus) woods were obtained from the plantations of the Southeast region of Vietnam, with the initial humidity of 80 - 85%. The wood was cut into boards with dimensions of 40 x 80 mm to 120 x 500 mm. In this study, the Pinus kesiya and Podocarp woods were thermally treated at with high temperatures ranging from 161oC to 218oC and the duration from 7.5 h to 13 h. The experiment results showed that the oven-dry density of pine and Bach tung tended to decrease when it was treated at high temperatures during long periods of time. In particular, the density of Pinus kesiya and Podocarp woods decreased about 3.17 - 17.3% and 3.45 - 20.73%, respectively, compared with the control samples. In the thermal modification process, under the effects of high temperature Pinus kesiya and Podocarp woods became darker than the modified wood

2021 ◽  
Vol 1208 (1) ◽  
pp. 012025
Author(s):  
Redžo Hasanagić ◽  
Sauradipta Ganguly ◽  
Ermin Bajramović ◽  
Adem Hasanagić

Abstract Wood is one of the most important construction materials in Europe and its use in building applications has increased in the recent decades. To enable even more extensive and reliable use of wood, this article aimed to determine the effect of thermal modification on mechanical properties of fir wood (lat. Abies sp.), linden wood (lat. Tilia sp.), and beech wood (lat. Fagus sp.). The thermal modification was conducted in a laboratory oven at five different temperatures of 170, 180, 195, 210, 220 °C and processed with a different maximum duration of the process of 78, 120, 180, 240, 276 minutes. Mechanical properties of treated wood have shown statistically insignificant fluctuations at lower temperatures compared to control samples. On the other hand, raising the temperature to 210 °C significantly affected the strength of all the species. The results revealed that thermal modification at high temperatures and longer exposure causes a decrease in the maximum force of the three wood species.


1938 ◽  
Vol 29 (2) ◽  
pp. 125-140 ◽  
Author(s):  
R. C. Muirhead Thomson

Reactions to Temperature1. The reactions of Culex fatigans to temperature were studied by means of a new type of temperature gradient apparatus based on the same principle as the humidity alternative chamber.2. Females at different stages were exposed to a range of 5°C. at different parts of the temperature scale, and it was found that the sensitivity was very much greater at high temperatures than at low ones.3. The most striking feature of behaviour at all stages was the strong avoidance of high temperatures. This was strongest in the hungry females, less strong in the blood-fed females and those with mature ovaries, and least strong in the newly emerged females.4. Newly emerged females showed avoidance of high temperature below 30°C., but not below 25°C. They also showed a weak avoidance of low temperature. At 29°C. they were sensitive to a difference of 1°C. or a gradient of 0·05°C. per cm.5. Hungry females showed a strong avoidance of high temperature below 25°C., the reaction still taking place below 15°C. There was no avoidance of low temperatures.6. Blood-fed females and those with mature ovaries showed a strong avoidance of high temperatures below 25°C., but below 20°C. they were unaffected by temperature differences. Blood-fed females were sensitive to a difference of 1°C. or a gradient of 0·05°C. per cm. at 23°C.7. Except in the case of newly emerged females there was quite a close relation between the reactions to temperature and the effects of temperature.8. Reasons are given for regarding the temperature reactions of Culex as of first importance in determining the behaviour of the mosquitoes when seeking a resting place.Reactions to Humidity9. The reactions of Culex fatigans to humidity were studied by means of the alternative chamber, in a dark constant temperature room at 25°C.10. At all stages the strongest humidity reaction was an avoidance of high humidities above 95 per cent. R.H.11. This reaction was strongest in the blood-fed females and those with mature ovaries, less strong in the newly emerged females, and weakest in the hungry females.12. The avoidance of high humidity was strongest when there was a difference of 20 per cent. R.H., such as a 78–98 per cent. R.H. gradient. Near saturation point all stages except hungry females were sensitive to a difference of 1 per cent. R.H. or a gradient of ·05 per cent. R.H. per cm. Hungry females at this point were not sensitive to a difference of less than 3 per cent. R.H.13. All stages showed a slight but regular avoidance of low humidities, provided a sufficiently large humidity range, not less than 40 per cent. R.H., was present.14. Hungry females, despite the onset of mortality due to desiccation, showed no sharp avoidance of low humidities which were rapidly fatal to them.15. Between 30 and 85 per cent. R.H. all stages were unaffected by humidity differences of as much as 40 per cent. R.H.16. The avoidance of high humidities was equally strong in blood-fed females at 20, 25, and 30°C. At 35°C., greatly increased activity eliminated the reaction.17. The reaction was much less intense in daylight and disappeared altogether after sundown.18. Reasons are given for considering that the measure of humidity which determines the behaviour of the mosquito is relative humidity and not saturation deficiency, even though the latter is the important one in the water relations of insects.


2008 ◽  
Vol 368-372 ◽  
pp. 1785-1787
Author(s):  
Tao Zeng ◽  
Dai Ning Fang ◽  
Xia Mei Lu ◽  
Fei Fei Zhou

This paper presents a theoretical model to predict the fracture strength of ultra-high temperature ceramics (UHTCs). According to different mechanisms, the environmental temperature is divided into four ranges. Effects of temperature and oxidation on the fracture strength of UHTCs are investigated in each temperature range. The results show that oxidation plays an important role in enhancing the fracture strength of UHTCs at high temperatures.


Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1491
Author(s):  
Olga Bytner ◽  
Agnieszka Laskowska ◽  
Michał Drożdżek ◽  
Paweł Kozakiewicz ◽  
Janusz Zawadzki

Black poplar (Populus nigra L.) was thermally modified in nitrogen atmosphere. The effects of the modification process on poplar wood were evaluated for temperatures: 160 °C, 190 °C, and 220 °C applied for 2 h; and 160 °C and 190 °C for 6 h. The percentual impact of temperature and time of modification on the properties of modified wood was analysed. The study permitted the identification correlations between the chemical composition and selected physical properties of thermally modified poplar wood. The dimensional stability of poplar wood was improved after thermal modification in nitrogen. The higher the temperature of modification, the lower the equilibrium moisture content (EMC) of black poplar. At the temperature of 220 °C, EMC was two times lower than the EMC of non-modified black poplar. It is also possible to reduce the dimensional changes of wood two-fold (at the modification temperature of 220 °C), both in radial and tangential directions, independently of the acclimatization conditions (from 34% to 98% relative humidity, RH). Similar correlations have been found for wood that has been soaked in water. Higher modification temperatures and longer processing times contributed to a lower swelling anisotropy (SA).


2011 ◽  
Vol 314-316 ◽  
pp. 1154-1158
Author(s):  
Wen Jun Hu ◽  
Ruo Ze Xie ◽  
Xi Cheng Huang ◽  
Yi Xia Yan

A high temperature split Hopkinson pressure bar (SHPB) test system is used to investigate the effects of temperature as well as those of strain and strain-rate. Effects of temperature for the vanadium alloy (V-5Cr-5Ti) are investigated by developing a high temperature SHPB test system. In this work, high temperatures greater than 1100°C are attained in the SHPB test specimens by using a synchronically assembled heating system .When testing with the high-temperature SHPB apparatus, care is required to prevent oxidation of the surface of the specimen, and to prevent an inhomogeneous temperature distribution from developing in the specimen. To determine the true flow stress–true strain relationship, specimens are tested from 15°C to 1100°C and at a strain-rate of about 3000 s-1: The parameters for a Johnson–Cook constitutive equation is determined from the test results. The Johnson–Cook constitutive equation is suitable for expressing the dynamic behavior of the V-5Cr-5Ti vanadium alloy.


Holzforschung ◽  
2015 ◽  
Vol 69 (7) ◽  
pp. 851-862 ◽  
Author(s):  
Mark Hughes ◽  
Callum Hill ◽  
Alexander Pfriem

Abstract The mechanical properties of thermally modified wood are discussed with regard to toughness. The molecular origins of the mechanical properties and, in particular, the role of the hemicelluloses are considered. The important role of water and its interaction with the cell wall components is also examined. The properties are discussed from the point of view of composite theory, with the three main macromolecular components acting as reinforcement, matrix and interfacial coupling agent. The important role that hemicelluloses play as a coupling agent between the cellulosic microfibril reinforcement and the lignin-rich matrix is highlighted. Destruction of the hemicelluloses during the thermal modification process has a profound effect upon the mechanical behaviour.


2017 ◽  
Vol 265 ◽  
pp. 266-271
Author(s):  
Ruslan R. Safin ◽  
P.A. Kaynov ◽  
Elena A. Beliakova

Thermal modification is a modern demanded technology allowing receiving natural environmentally friendly material with increased bioproofness and dimensional stability. However, the known technologies of heat treatment of massive wood are rather power-intensive therefore an urgent task is to decrease the energy consumption rate of this process. For this purpose the authors have suggested the technology at which the flue gases, received by gasification of waste of the wood processing industry, act as the agent of processing. The results of the research of this process are presented in the article, the rational modes of processing for concrete types of timber (oak, pine and birch, thickness from 30 to 60 mm) are defined and also the interrelation between the moist characteristics of the wood fuel used for receiving flue gas and the technological modes of processing of massive wood are established. It is also defined that the thickness and breed of material, namely the maintenance of pentosanes as a part of the modified wood exerts impact on the process of thermal decomposition of timber.


Holzforschung ◽  
2014 ◽  
Vol 68 (3) ◽  
pp. 323-326 ◽  
Author(s):  
Lauri Rautkari ◽  
Callum A.S. Hill

Abstract The effects of initial moisture content (MC) on anti-swelling efficiency (ASE), mass loss (ML), and equilibrium MC (EMC) at 65% relative humidity of thermally modified Scots pine sapwood under saturated steam (TMSA) has been investigated. ML during the TMSA process was higher with the specimens containing moisture before modification compared with initially dry specimens. Surprisingly, the EMC of the modified specimens with initial moisture was higher than that observed with the modified wood that was initially dry before the modification process. Higher initial MC before thermal modification results in a lower ASE.


Horticulturae ◽  
2021 ◽  
Vol 7 (11) ◽  
pp. 484
Author(s):  
Samia Samad ◽  
Denis Butare ◽  
Salla Marttila ◽  
Anita Sønsteby ◽  
Sammar Khalil

The growing interest in using everbearing (EB) strawberry cultivars to extend the cultivation period has faced some challenges. These include poor runner production due to its perpetual flowering nature; irregular flowering behavior and extended periods of high temperature have caused floral inhibition and reduced yield. As flowering is an interplay between temperature and photoperiod, it is important to investigate the effects of this interaction on the cultivation. Therefore, this study used meristem dissection as a tool to study the effect of temperature and photoperiod on meristem development. Tray plants of two EB strawberry cultivars ‘Florentina’ and ‘Favori’ were grown at 20 °C, 25 °C, and 30 °C under short day (SD) conditions, and subsequently at 20 °C under long day (LD) conditions. The meristem development was analysed every 6 weeks for a 15-week period in SD and for 14 weeks in LD conditions using meristem dissection. The plants showed similar flowering patterns to previously studied everbearing cultivars, which was qualitative LD plants at high temperatures and quantitative LD plants at lower temperatures. Our results show that meristem dissection can be used to determine the temperature and photoperiodic effect on meristem development, and for the occurrence of cropping peaks, and can therefore be used to decide the environmental input and to evaluate yield potential.


2003 ◽  
Vol 762 ◽  
Author(s):  
A. Gordijn ◽  
J.K. Rath ◽  
R.E.I. Schropp

AbstractDue to the high temperatures used for high deposition rate microcrystalline (μc-Si:H) and polycrystalline silicon, there is a need for compact and temperature-stable doped layers. In this study we report on films grown by the layer-by-layer method (LbL) using VHF PECVD. Growth of an amorphous silicon layer is alternated by a hydrogen plasma treatment. In LbL, the surface reactions are separated time-wise from the nucleation in the bulk. We observed that it is possible to incorporate dopant atoms in the layer, without disturbing the nucleation. Even at high substrate temperatures (up to 400°C) doped layers can be made microcrystalline. At these temperatures, in the continuous wave case, crystallinity is hindered, which is generally attributed to the out-diffusion of hydrogen from the surface and the presence of impurities (dopants).We observe that the parameter window for the treatment time for p-layers is smaller compared to n-layers. Moreover we observe that for high temperatures, the nucleation of p-layers is more adversely affected than for n-layers. Thin, doped layers have been structurally, optically and electrically characterized. The best n-layer made at 400°C, with a thickness of only 31 nm, had an activation energy of 0.056 eV and a dark conductivity of 2.7 S/cm, while the best p-layer made at 350°C, with a thickness of 29 nm, had an activation energy of 0.11 V and a dark conductivity of 0.1 S/cm. The suitability of these high temperature n-layers has been demonstrated in an n-i-p microcrystalline silicon solar cell with an unoptimized μc-Si:H i-layer deposited at 250°C and without buffer. The Voc of the cell is 0.48 V and the fill factor is 70 %.


Sign in / Sign up

Export Citation Format

Share Document