AFM Studies on Silica Dispersion in EPDM Rubber

2010 ◽  
Vol 83 (2) ◽  
pp. 123-132 ◽  
Author(s):  
N. Natchimuthu
Keyword(s):  
Epoxy Resin ◽  
Coupling Agents ◽  
Epdm Rubber ◽  
Force Microscopy ◽  
Precipitated Silica ◽  
Morphological Studies ◽  
Atomic Force ◽  
Rubber Compounds ◽  
Silica Fillers ◽  
Silica Dispersion

Abstract EPDM rubber formulations filled with precipitated silica and cross-linked by peroxide vulcanization have been investigated with the objective of realizing better processing characteristics and vulcanizate properties. Dispersion of silica in EPDM rubber in the presence of conventional coupling agents and in the presence of an epoxy resin has been investigated using atomic force microscopy (AFM) and scanning electron microscopy (SEM). AFM results of EPDM rubber compounds containing silica fillers in the presence of the epoxy resin have exhibited improved silica dispersion in terms of scanned height. The latter has been found to be in the range of 0–100 nm for EPDM rubber—silica systems with epoxy resin, while in the absence of the resin, scanned height has been found to be in the range of 0–700 nm. The significant reduction in scanned height in the presence of epoxy resin has been attributed to the reduction in surface roughness which is an indication for good dispersion of silica in the rubber. Morphological studies using SEM, mechanical properties, and Mooney-Rivlin constants all have shown significant improvement in performance properties of EPDM rubber—silica compounds containing epoxy resin and vulcanized with dicumyl peroxide.

scholarly journals Optical, Structural and Electrical Properties of Electrochemical Synthesis of Thin Film of Polyaniline

2018 ◽  
Vol 15 (1) ◽  
pp. 73-80 ◽  
Author(s):  
Baghdad Science Journal
Keyword(s):  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Morphological Studies ◽  
Atomic Force ◽  
Vis Spectroscopy ◽  
Structural And Electrical Properties ◽  
A Cell ◽  
Ft Ir ◽  
Ir And Raman

Polyaniline membranes of aniline were produced using an electrochemical method in a cell consisting of two poles. The effect of the vaccination was observed on the color of membranes of polyaniline, where analysis as of blue to olive green paints. The sanction of PANI was done by FT-IR and Raman techniques. The crystallinity of the models was studied by X-ray diffraction technique. The different electronic transitions of the PANI were determined by UV-VIS spectroscopy. The electrical conductivity of the manufactured samples was measured by using the four-probe technique at room temperature. Morphological studies have been determined by Atomic force microscopy (AFM). The structural studies have been measured by (SEM).

Using Demercurated Lighting Phosphor and MSWI Scrubber Residues to Prepare High Performance Plastic Concrete

2009 ◽  
Vol 610-613 ◽  
pp. 55-60
Author(s):  
Wu Jang Huang ◽  
Wei Chu ◽  
Ling Hui Hsieh ◽  
Jian Guo Chen
Keyword(s):  
Thermal Properties ◽  
Epoxy Resin ◽  
Solid Waste ◽  
High Performance ◽  
Waste Incineration ◽  
Type I ◽  
Phosphor Powder ◽  
Force Microscopy ◽  
Atomic Force ◽  
Plastic Concrete

This study aimed to prepare a high performance plastic concrete made of epoxy resin and Portland type-I cement mixed with at least one inorganic solid waste of demercurated lighting phosphor powder or municipal solid waste incineration scrubber residue. The ratio between liquid epoxy resin and cement was 1:2; the scrubber residue and demercurated phosphor powder were added as modifiers for cement component in order to improve the strength and thermal properties of synthesized plastic concrete. The results indicate that, the addition of scrubber residue causes a decrease in both strength and thermal properties; whereas, the demercurated phosphor powder can replace 100% of the contents of cement without any significantly change in either strength or thermal properties. Atomic force microscopy and Raman spectroscopy were used to characterize the chemical structure of cured concrete and the results indicate that the surface softness increases with an increase in the mixed percentage of epoxy resin.

Structural and Optical Characterization of Synthesized TiO2 Nanopowder Using Sol–Gel Technique

2016 ◽  
Vol 15 (01n02) ◽  
pp. 1650002 ◽  
Author(s):  
S. Lourduraj ◽  
R. Victor Williams
Keyword(s):  
Anatase Phase ◽  
Sol Gel ◽  
Visible Spectrum ◽  
Average Crystallite Size ◽  
Xrd Analysis ◽  
Force Microscopy ◽  
Morphological Studies ◽  
Atomic Force ◽  
Gel Technique

The nanocrystalline TiO2 powder was synthesized by sol–gel method. The XRD analysis reveals that TiO2 powder was highly crystalline (anatase phase) and nanostructured with tetragonal system. The average crystallite size after calcined at 673[Formula: see text]K is found to be 7.7[Formula: see text]nm. The surface morphological studies using scanning electron microscopy (SEM) exhibit that the formation of nanosized TiO2 particles with less densification nature. Atomic force microscopy (AFM) topography exhibits the uniform distribution of spherical-shaped particles. The energy dispersive X-ray spectroscopy (EDX) confirms the presence of Titanium and Oxygen in synthesized TiO2 nanopowder. The value of optical bandgap of TiO2 nanopowder calculated from UV-Visible spectrum is 3.45[Formula: see text]eV. The presence of TiO2 particles is confirmed from the dominant fourier transform infrared (FTIR) peaks at 621[Formula: see text]cm[Formula: see text] and 412[Formula: see text]cm[Formula: see text].

scholarly journals Optical and Morphological Studies of Thermally Evaporated PTCDI-C8 Thin Films for Organic Solar Cell Applications

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Ronak Rahimi ◽  
V. Narang ◽  
D. Korakakis
Keyword(s):  
Thin Films ◽  
Silicon Substrates ◽  
High Electron ◽  
Ambient Conditions ◽  
Force Microscopy ◽  
Morphological Studies ◽  
Atomic Force ◽  
Organic Semiconductor Devices ◽  
Thermal Evaporator ◽  
High Degree

PTCDI-C8 due to its relatively high photosensitivity and high electron mobility has attracted much attention in organic semiconductor devices. In this work, thin films of PTCDI-C8 with different thicknesses were deposited on silicon substrates with native silicon dioxide using a vacuum thermal evaporator. Several material characterization techniques have been utilized to evaluate the structure, morphology, and optical properties of these films. Their optical constants (refractive index and extinction coefficient) have been extracted from the spectroscopic ellipsometry (SE). X-ray reflectivity (XRR) and atomic force microscopy (AFM) were employed to determine the morphology and structure as well as the thickness and roughness of the PTCDI-C8 thin films. These films revealed a high degree of structural ordering within the layers. All the experimental measurements were performed under ambient conditions. PTCDI-C8 films have shown to endure ambient condition which allows pots-deposition characterization.

scholarly journals Effect of Modification with Various Epoxide Compounds on Mechanical, Thermal, and Coating Properties of Epoxy Resin

2016 ◽  
Vol 2016 ◽  
pp. 1-13 ◽  
Author(s):  
Alaaddin Cerit ◽  
Mustafa Esen Marti ◽  
Ulku Soydal ◽  
Suheyla Kocaman ◽  
Gulnare Ahmetli
Keyword(s):  
Thermal Stability ◽  
Atomic Force Microscopy ◽  
Tensile Strength ◽  
Epoxy Resin ◽  
Curing Process ◽  
Coating Properties ◽  
Corrosive Media ◽  
Force Microscopy ◽  
Atomic Force ◽  
Thermal Stability Of

Epoxy resin (ER) was modified with four different epoxide compounds, 4,5-epoxy-4-methyl-pentane-2-on (EMP), 3-phenyl-1,2-epoxypropane (PhEP), 1-chloro-2,3-epoxy-5-(chloromethyl)-5-hexene (CEH), and a fatty acid glycidyl ester (FAGE), to improve its chemical and physical properties. The effects of the addition and amount of these modifiers on mechanical, thermal, and coating properties were investigated. Atomic force microscopy was used to observe the changes obtained with the modification. The influence of the modifying agents on the curing process was monitored through FTIR spectroscopy. The curing degrees of ER and modified ERs (M-ERs) were found to be over 91%. The results showed that tensile strength of ER improved till 30% (wt.) with addition of the modifier content. Modification with EMP and PhEP remarkably enhanced the thermal stability of ER to be highly resistant to the corrosive media.

Effects of Annealing on Pulsed Laser Deposited TiO2 Thin Films

2013 ◽  
Vol 446-447 ◽  
pp. 306-311 ◽  
Author(s):  
Sudhanshu Dwivedi ◽  
Somnath Biswas
Keyword(s):  
Thin Films ◽  
Pulsed Laser ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Si Substrates ◽  
Morphological Studies ◽  
Atomic Force ◽  
Deposited Films ◽  
Type Crystal

Mixed phase TiO2 thin films of rutile and anatase type crystal orientations were deposited on Si substrates by pulsed laser deposition (PLD) technique. When annealed at 800°C at 1 mbar oxygen pressure for 3 h, the deposited films transform into a single phase of rutile type. Structural and morphological studies of the as-deposited and annealed films were performed with X-ray diffraction (XRD), Fourier transform infra-red spectroscopy (FTIR), Raman spectroscopy, and atomic force microscopy (AFM). Photoluminescence (PL) spectroscopy was used for optical characterization of the annealed thin films.

CHARACTERIZATION OF ALUMINUM SURFACES AFTER DIFFERENT PRETREATMENTS AND EXPOSURE TO SILANE COUPLING AGENTS

2001 ◽  
Vol 08 (01n02) ◽  
pp. 43-50 ◽  
Author(s):  
M. KONO ◽  
X. SUN ◽  
R. LI ◽  
K. C. WONG ◽  
K. A. R. MITCHELL ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Coupling Agents ◽  
Chemical Compositions ◽  
Silane Coupling Agents ◽  
Oh Groups ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Aluminum Surfaces

X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and scanning electron microscopy (SEM) have been used to characterize surfaces of aluminum which have been pretreated by mechanical polishing, acid etching and alkaline etching, as well as given subsequent exposures to air and water. These surfaces can differ markedly with regard to their chemical compositions and topographical structures. Characterizations of these surfaces after exposures to three organosilanes, γ-GPS, BTSE and γ-APS, indicate that the amount of silane adsorbed in each case shows a tendency to increase both with the number of OH groups detected at the oxidized aluminum and with the surface roughness. The XPS data are consistent with the adhesion of γ-APS occurring through H bonding, especially via NH3+ groups.

Synergistic effect of polyvinylpyrrolidone noncovalently modified graphene and epoxy resin in anticorrosion application

2020 ◽  
pp. 095400832094229
Author(s):  
Shifeng Wen ◽  
Jiacheng Ma
Keyword(s):  
Epoxy Resin ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Covalent Modification ◽  
Original Structure ◽  
Graphene Layers ◽  
Force Microscopy ◽  
Atomic Force ◽  
The Stability ◽  
Modified Graphene

In this article, polyvinylpyrrolidone (PVP) was used for the noncovalent modification on the surface of graphene. Compared with covalent modification, this method maintained the original structure of graphene layers, thereby maximizing the original properties of graphene. The π–π noncovalent bond was formed between PVP and graphene by X-ray photoelectron spectroscopy analysis, indicating that PVP successfully modified graphene. The thickness of graphene layer was measured by atomic force microscopy, which showed that the distance between graphene layers was increased by 5–6 nm, and the stability of the modified graphene in N, N-dimethylformamide was remarkably improved. The obtained composite coating by combination of the modified graphene and the epoxy resin was subjected to electrochemical impedance test to obtain the best anticorrosive effect of the coating with the graphene content of 0.3 wt%. The results showed that the addition of graphene to the epoxy resin could effectively improve the anticorrosive effect. Meanwhile, the good electrical conductivity allowed the electrons which lost from the substrate to led to air or saline rapidly, thereby reducing the combination of iron ions with oxygen and the generation of corrosion products (iron oxides).

scholarly journals Properties and Characterization of New Approach Organic Nanoparticle-Based Biocomposite Board

Polymers ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2236
Author(s):  
I. Ismail ◽  
Arliyani ◽  
Z. Jalil ◽  
Mursal ◽  
N. G. Olaiya ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Epoxy Resin ◽  
Testing Machine ◽  
Mesh Size ◽  
Coconut Shell ◽  
Force Microscopy ◽  
Properties And Characterization ◽  
Atomic Force ◽  
Transmission Electron ◽  
Shell Particles

Conventionally, panel boards are produced with material flex or microparticle with P.U. or U.F. as adhesives. However, in this study, nanoparticle with epoxy resin as an adhesive was used to produce nanoboard. Coconut shell nanoparticle composite with epoxy resin as an adhesive was prepared using a compression molding technique. The coconut shell particles were originally 200 mesh size and then milled mechanically with a ball mill for the duration of 10, 20, 30, and 40 h (milling times) to produce nanoparticles. The composition ratio of the composite is 85 vol.% of coconut shell and 15 vol.% of epoxy resin. The formation of nanoparticles was observed with transmission electron microscopy (TEM). The mechanical, physical, and microstructure properties of the composite were examined with X-ray diffraction, scanning electron microscopy, atomic force microscopy, and universal testing machine. The results established that the properties of the composite (microstructures, mechanical, and physical) are influenced by the duration of milling of coconut shell particles. The modulus and flexural strength of the composite improved with an increase in the milling time. The density, thickness swelling, and porosity of the composite were also influenced by the milling times. The result suggested that the composite properties were influenced by the particle size of the coconut shell. The coconut shell nanoparticle composite can be used in the manufacturing of hybrid panels and board.

Sign in / Sign up

Export Citation Format

Share Document