A New Type of Tackmeter

1964 ◽  
Vol 37 (1) ◽  
pp. 28-37 ◽  
Author(s):  
O. K. F. Bussemaker ◽  
W. V. C. van Beek
Keyword(s):  
Testing Procedure ◽  
Test Results ◽  
Factors Affecting ◽  
Sample Compression ◽  
New Type

Abstract A new type of tackmeter is described. Strips of the material to be tested are used for tack measurements. The instrument compresses and separates the strips under conditions which can be arbitrarily selected. The tackmeter is of rugged design for simple handling and ease of operation. The test results are recorded on a chart, enabling easy reading of the results. A description of the tackmeter and the testing procedure is given. The accuracy of the measurement is briefly discussed. Among the factors affecting the measurement are the thickness of the sample, compression conditions and aging of the surface. Some test results obtained with factory-made plies and compounds with varying black loadings are given.

scholarly journals Influencing Factors on the Accuracy of Soil Calibration Models by EDG

Processes ◽  
2021 ◽  
Vol 9 (11) ◽  
pp. 1892
Author(s):  
Haoming Yang ◽  
Xiaoping Yang ◽  
Min Zhang ◽  
Jiaojian Hou
Keyword(s):  
Water Content ◽  
Correlation Coefficients ◽  
Dry Density ◽  
Engineering Practice ◽  
Calibration Model ◽  
Test Results ◽  
Probability Curve ◽  
Factors Affecting ◽  
Applicable Range ◽  
New Type

Compaction is an important standard in evaluating the quality of earth filling work. The EDG, an electrical density gauge, is a new type of fast and nondestructive compaction detection equipment. It is used to test the dry density and water content of the soil by establishing a soil calibration model while the accuracy of measurement is mainly based on the precision of equation of calibration model. In this paper, the factors affecting the accuracy of the soil calibration model were studied by an indoor calibration test, and soil samples were prepared to verify the accuracy of the soil calibration model. The test results showed that the dry density range, water content range, and sample quantity 13 samples of soil had a significant influence on the correlation coefficient (R2) of the equation of the soil calibration model. In addition, when using the calibration model with different sample numbers and sample combinations but similar correlation coefficients to test multiple groups of density and moisture content, there are also differences in the expected value and standard deviation of the error probability curve of the test results. In the engineering practice, the reasonable sample quantity was determined by the applicable range of dry density and water content obtained from the measurement error analysis of the soil calibration model.

Cut Flowers Being Sold as Impulse Items: A Look at Factors Affecting Impulse Product Merchandising

HortScience ◽  
1998 ◽  
Vol 33 (3) ◽  
pp. 558c-558
Author(s):  
Jennifer B. Neujahr ◽  
Karen L.B. Gast
Keyword(s):  
Consumer Behavior ◽  
Marketing Strategies ◽  
Easy Access ◽  
Future Research ◽  
Grocery Stores ◽  
Cut Flowers ◽  
Factors Affecting ◽  
New Type ◽  
The 1950S ◽  
The Way

Consumer behavior research seems to play an big role in determining the wants and needs of an industry. This research helps to shape the way we market to the consumers and helps make marketing strategies more effective. In the 1950s grocery stores began to sell horticulture products in order to alleviate the growers' surplus. Supermarkets now have seem to found their niche in this market due to the fact that they can influence their consumers to buy their flowers right along with their bread, and get all of their shopping done at once. This new type of sale, commonly referred to as the impulse sale, can relate directly to how well the store is merchandised and maintained. A study was conducted at a local supermarket, to determine the following: good locations for impulse sales items, special conditions affecting impulse sales items, and what types of things could affect demand for impulse items. It was discovered that certain locations make better sales than other locations. Locations that were front and center and allowed easy access to seeing the mixed flower bouquet without having to touch it yielded the best results. The variables used to show a change in demand showed little to some variability and has raised some questions which may be used to conduct future research.

Improving the Strength of Abrasive Wheels and Optimizing the Control over the Strength of Composite Abrasive Materials

2019 ◽  
Vol 946 ◽  
pp. 380-385
Author(s):  
Boris A. Chaplygin ◽  
Viacheslav V. Shirokov ◽  
Tat'yana A. Lisovskaya ◽  
Roman A. Lisovskiy
Keyword(s):  
Mechanical Properties ◽  
Test Results ◽  
Key Factors ◽  
Special Equipment ◽  
Material Density ◽  
Factors Affecting ◽  
Control Factors ◽  
Reinforcing Material ◽  
Special Studies ◽  
First Time

The strength of abrasive wheels is one of the key factors affecting the performance of abrasive machining. The paper discusses ways to improve the strength of abrasive wheels. The stress-state mathematical model presented herein is a generalization of the existing models. It is used herein to find for the first time that there are numerous optimal combinations of the elastic modulus and reinforcing material density, which result in the same minimum value of the objective function. It is found out that increasing the radius of the reinforcing component while also optimizing the mechanical properties of its material may increase the permissible breaking speed of the wheel several times. We herein present a regression equation and a nomogram for finding the optimal combination of control factors. Conventional methods for testing the mechanical properties of materials, which have been proven reliable for testing metals and alloys, are not as reliable for testing abrasive materials, as the test results they generate are not sufficiently stable or accurate. We therefore propose an alternative method that does not require any special equipment or special studies.

scholarly journals Evaluation of Bleeding Resistance in Chip Seal and Asphalt Emulsion Residue Rheology

Coatings ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 670
Author(s):  
Preeda Chaturabong
Keyword(s):  
Influence Factors ◽  
Application Rate ◽  
Test Methods ◽  
Test Results ◽  
Asphalt Emulsion ◽  
Aggregate Gradation ◽  
Factors Affecting ◽  
Promising Tool ◽  
Chip Seal ◽  
Asphalt Emulsions

Chip seal bleeding is influenced by many factors, including design inputs, material properties, and project-specific conditions. It reduces the surface texture of the pavement and thus compromises the safety of the traveling public. Even though factors that bring about premature bleeding are known, currently, no laboratory test methods for evaluating bleeding in chip seals have been specified. The objective of this paper is to present the results of an investigation of the influence factors of asphalt emulsion residue properties measured by the ASTM D7405 multiple stress creep and recovery (MSCR) test, as well as other factors related to chip seal bleeding resistance as measured by the modified loaded wheel test (MLWT). In this study, the MSCR test was used as a tool for evaluating the performance of asphalt emulsions because it has been identified as a potential test related to bleeding in the field. In addition, MLWT was selected as a tool for evaluating chip seal bleeding performance in the laboratory. The results of the MLWT showed that the emulsion application rate (EAR), aggregate gradation, and emulsion properties were significant factors affecting bleeding. The MSCR test was found to be a promising tool for the performance evaluation of asphalt emulsion residue, as the test was able to differentiate between emulsion chemistries and modifications in terms of sensitivity to both temperature and stress. In relation to chip seal bleeding resistance, only the creep compliance (Jnr) obtained from the MSCR test results was identified as a significant property affecting potential for bleeding.

Field Tests of Guide Vanes and Runner Blades of a Large Bulb Turbine for Output Deficiency Diagnosis

2012 ◽  
Vol 212-213 ◽  
pp. 1057-1061 ◽  
Author(s):  
Zhong Liu ◽  
Zhu Qing Huang ◽  
Shu Yun Zou ◽  
Hong De Rao
Keyword(s):  
Field Tests ◽  
Economic Loss ◽  
Hydropower Plant ◽  
Test Results ◽  
Guide Vanes ◽  
Factors Affecting ◽  
Runner Blade ◽  
Main Factors ◽  
Theoretical Analyses ◽  
Bulb Turbine

The 3# bulb turbine in Hongjiang Hydropower Plant has faced the problem of output deficiency since its commission in Sept. 2003, which caused a large economic loss. Following simple theoretical analyses on the main factors affecting the turbine’s output and efficiency, the field test schemes were determined to measure the shapes and intervals of guide vanes and runner blades of the 3#, 5# and 6# turbines. The test results discover that the average blade intervals of the 3# turbine are generally less than those of the 5# one. Suggestions on runner blade installation adjustment and combined curve modification are given.

scholarly journals An Index of Regional Snow-Pack Stability based on Natural Slab Avalanches

1985 ◽  
Vol 31 (108) ◽  
pp. 67-73
Author(s):  
Arthur Judson ◽  
Rudy M. King
Keyword(s):  
Real Time ◽  
Testing Procedure ◽  
Statistical Distribution ◽  
Colorado Front Range ◽  
Sequential Testing ◽  
Test Results ◽  
Snow Pack ◽  
Front Range ◽  
Time Evaluation

AbstractAn index of regional snow-pack stability based on occurrences of natural slab avalanches was developed using a statistical distribution and a sequential testing procedure. The study interprets avalanche information on 185 paths in the Colorado Front Range. Results show general agreement with operational hazard estimates; test results have real-time evaluation potential.

Experimental Study on Shear Behavior of Perfobond Connector with Boot Shaped Slots

2019 ◽  
Author(s):  
Zhanchong Shi ◽  
Qingtian Su ◽  
Xinyi He ◽  
Quanlu Wang ◽  
Kege Zhou ◽  
...  
Keyword(s):  
Failure Modes ◽  
Shear Stiffness ◽  
Shear Capacity ◽  
High Shear ◽  
Test Results ◽  
Precise Location ◽  
Construction Problem ◽  
Circular Holes ◽  
New Type ◽  
Push Out

<p>In order to solve the construction problem of perforating rebars’ precise location and it’s getting through the circular holes for the the conventional perfobond connector, a new type of perfobond connector with boot shaped slots was proposed. This new type perfobond connector has the advantage of convenient construction and pricise location. Three groups of push-out tests with nine specimens were carried out to study the shear capacity of the new type perfobond connector. The effect of the number and the spacing of boot shaped slots on failure modes, shear capacity, peak slip and shear stiffness were mainly studied. The test results show that the new type of perfobond connector with boot shaped slots has a high shear capacity and a good ductility, it could be widely applied on the connection between the steel and the concrete structures.</p>

scholarly journals The small strain stiffness from bender elements tests for clayey soils

2018 ◽  
Vol 50 (4) ◽  
pp. 353-371
Author(s):  
Katarzyna Markowska-Lech ◽  
Wojciech Sas ◽  
Mariusz Lech ◽  
Katarzyna Gabryś ◽  
Alojzy Szymański
Keyword(s):  
Field Tests ◽  
Small Strain ◽  
Test Results ◽  
Bender Elements ◽  
Element Analysis ◽  
Factors Affecting ◽  
Small Strain Stiffness ◽  
Seismic Wave Velocities ◽  
Case Basis ◽  
Hardening Soil Model

Abstract The shear modulus of soils at small strain (G0) is one of the input parameters in a finite element analysis with the hardening soil model with small strain stiffness, required in the advanced numerical analyses of geotechnical engineering problems. The small strain stiffness can be determined based on the seismic wave velocities measured in the laboratory and field tests, but the interpretation of test results is still under discussion because of many different factors affecting the measurements of the wave travel time. The recommendations and proposed solutions found in the literature are helpful as a guide, but ought to be adopted with a certain measure of care and caution on a case-by-case basis. The equipment, procedures, tests results and interpretation analyses of bender elements (BE) tests performed on natural overconsolidated cohesive soils are presented.

scholarly journals ANALISYS OF THE INFLUENCE OF GLUE JOINTS ON THE MEASUREMENT OF PHYSICAL PROPERTIES OF STRUCTURAL ELEMENTS USING FIBER BRAGG GRATING

2020 ◽  
Vol 10 (3) ◽  
pp. 99-102
Author(s):  
Tomasz Zieliński ◽  
Łukasz Zychowicz
Keyword(s):  
Stainless Steel ◽  
Physical Properties ◽  
Fiber Bragg Grating ◽  
Transmission Spectrum ◽  
Measuring Transducer ◽  
Bragg Grating ◽  
Transmission Characteristic ◽  
Test Results ◽  
Structural Elements ◽  
Factors Affecting

The research presents the analysis of the influence of the glue connection on the measurement of elongation of stainless steel and aluminum samples by means of fiber Bragg grating (FBG) with uniform fibers used as a measuring transducer. Research indicates two possible factors affecting the deformation of the transmission spectrum obtained during elongation measurement. One of them is the type of adhesive that is used to make the connection between the fiber Bragg grating and the tested sample. The second possible factor is method of connection's execution. The need for research on glue connection resulted from the formation of defects mainly in the form of numerous side bands visible in the transmission spectrum during the measurement of elongations. The test results were presented in the form of graphs obtained on the basis of transmission characteristic.

scholarly journals DUKUNGAN KELUARGA TERHADAP TINGKAT KESEMBUHAN PASIEN COVID-19 DI RUANG ISOLASI RUMAH SAKIT AMINAH 2021

2021 ◽  
Vol 7 (2) ◽  
pp. 164-169
Author(s):  
Agah Nugraha ◽  
Rostime Hermayerni Simanullang
Keyword(s):  
Family Support ◽  
Virus Disease ◽  
Sampling Technique ◽  
Statistical Test ◽  
P Value ◽  
Test Results ◽  
Raising Children ◽  
The Family ◽  
New Type

 Corona virus Disease 2019 (COVID-19) is an infectious disease caused by Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2). SARS-CoV-2 is a new type of coronavirus that has never been previously identified in humans. Family support is an activity oriented to improve family functions on the basis of raising children and other family activities. in a system and resources that support. This study aims to identify family support for the healing rate of Covid-19 patients in the Isolation Room at Aminah Hospital, Tangerang in 2021. Method: observational analytic used in this research and 23 covid-19 participantn,  in this study using the Total Sampling technique. Statistical test used is the Spearman Rank statistical test. Results: The results of study obtained p value = 0.000 <0.05. Conclusion: there is a relationship between family support and the healing of  Covid-19 patients.  The role of the family is very important. and breaking chain of spread of the Covid-19.

Sign in / Sign up

Export Citation Format

Share Document