Ethylene-Propylene Copolymers Produced with Soluble Catalysts

1962 ◽  
Vol 35 (4) ◽  
pp. 1101-1113
Author(s):  
R. J. Kelly ◽  
H. K. Garner ◽  
H. E. Haxo ◽  
W. R. Bingham
Keyword(s):  
Physical Properties ◽  
Heterogeneous Catalysts ◽  
Accelerated Aging ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Ethylene Propylene ◽  
Aging Properties ◽  
Aluminum Halide ◽  
Catalyst Systems ◽  
Catalyst Efficiency

Abstract Soluble catalyst systems derived from alkyl aluminum halides in combination with vanadium oxytrichloride or tetrachloride produce highly random ethylene-propylene copolymers with high catalyst efficiency. By the choice of the alkyl aluminum halide and molar ratio of aluminum to vanadium, variations in polymerization efficiency and molecular weight are possible. The copolymers prepared with these soluble catalysts show advantages in both processing and physical properties over those prepared with heterogeneous catalysts. Vulcanizates of these copolymers show somewhat different accelerated aging properties depending on the additive used along with the peroxide. Low temperature properties of copolymers containing less than 70 weight % propylene show a tendency for crystallization which is not shown by X-ray diffraction. Overall physical properties and tire tests show some preference for the 65 weight % propylene copolymer over the 50% material.

Microstructure and Physical Properties of Clay-Polymer Composites

2000 ◽  
Vol 628 ◽  
Author(s):  
T.N. Blanton ◽  
D. Majumdar ◽  
S.M. Melpolder
Keyword(s):  
Composite Materials ◽  
Physical Properties ◽  
Polymer Composites ◽  
Basal Plane ◽  
X Ray Diffraction ◽  
X Ray ◽  
Layered Clay

ABSTRACTClay-polymer nanoparticulate composite materials are evaluated by the X-ray diffraction technique. The basal plane spacing provided information about the degree of intercalation and exfoliation of the 2: 1 layered clay structure. Both intercalation and exfoliation are controlled by the identity of the polymer and the clay:polymer ratio.

On the Properties of an Ion Conductive System Incorporated in Hybrid Films

2000 ◽  
Vol 628 ◽  
Author(s):  
G. González ◽  
P. J. Retuert ◽  
S. Fuentes
Keyword(s):  
Electrochemical Impedance ◽  
Ternary Phase Diagram ◽  
Lithium Perchlorate ◽  
Molar Ratio ◽  
Ionic Conductors ◽  
X Ray Diffraction ◽  
Poly Ethylene Oxide ◽  
Ion Conducting ◽  
Poly Ethylene ◽  
High Degree

ABSTRACTBlending the biopolymer chitosan (CHI) with poly (aminopropilsiloxane) oligomers (pAPS), and poly (ethylene oxide) (PEO) in the presence of lithium perchlorate lead to ion conducting products whose conductivity depends on the composition of the mixture. A ternary phase diagram for mixtures containing 0.2 M LiClO4 shows a zone in which the physical properties of the products - transparent, flexible, mechanically robust films - indicate a high degree of molecular compatibilization of the components. Comparison of these films with binary CHI-pAPS nanocomposites as well as the microscopic aspect, thermal behavior, and X-ray diffraction pattern of the product with the composition PEO/CHI/pAPS/LiClO4 1:0.5:0.6:0.2 molar ratio indicates that these films may be described as a layered nanocomposite. In this composite, lithium species coordinated by PEO and pAPS should be inserted into chitosan layers. Electrochemical impedance spectroscopy measurements indicate the films are pure ionic conductors with a maximal bulk conductivity of 1.7*10-5 Scm-1 at 40 °C and a sample-electrode interface capacitance of about 1.2*10-9 F.

Effect of Hydrated Metal Salts on the Coordination Product of Cobalt(II) halide and PNP Type Ligand, 2,6-bis(di-tertbutylphosphinomethyl) pyridine

2018 ◽  
Author(s):  
Tasneem Siddiquee ◽  
Abdul Goni
Keyword(s):  
Metal Salts ◽  
Molar Ratio ◽  
Pincer Complexes ◽  
Asymmetric Unit ◽  
X Ray Diffraction ◽  
Pincer Ligand ◽  
Tetrahedral Geometry ◽  
X Ray ◽  
Distorted Tetrahedral Geometry ◽  
Cobalt Center

Chemical treatment of CoX<sub>2</sub><b><sup>. </sup></b>6H<sub>2</sub>O (X = Cl, Br, I) with the potentially tridentate PNP pincer ligand 2,6-bis(di-<i>tert</i>-butylphosphinomethyl)pyridine in 1:1 molar ratio results in cobalt(II) halide-PNP pincer complexes. The effect of the hydrated metal source on molecular structure and geometry of the complexes was studied by single crystal X-ray diffraction analysis. The complexes are neutral and the cobalt center adopts a penta-coordinate system with potential atropisomerization. Within the unit cell there are two distinct molecules per asymmetric unit. One of the two phosphorus atoms in the PNP ligand was observed to be partially oxidized to phosphinoxide. Disorder in the structure reflects a mixture of square pyramidal and distorted tetrahedral geometry.

scholarly journals Photocatalytic Reduction of CO2 to Methanol Using a Copper-Zirconia Imidazolate Framework

Catalysts ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 346
Author(s):  
Sonam Goyal ◽  
Maizatul Shima Shaharun ◽  
Ganaga Suriya Jayabal ◽  
Chong Fai Kait ◽  
Bawadi Abdullah ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalyst Support ◽  
Oxidation Potential ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Molar Ratios ◽  
Optimum Parameters ◽  
Reduction Of Co2 ◽  
Enhanced Yield

A set of novel photocatalysts, i.e., copper-zirconia imidazolate (CuZrIm) frameworks, were synthesized using different zirconia molar ratios (i.e., 0.5, 1, and 1.5 mmol). The photoreduction process of CO2 to methanol in a continuous-flow stirred photoreactor at pressure and temperature of 1 atm and 25 °C, respectively, was studied. The physicochemical properties of the synthesized catalysts were studied using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectroscopy. The highest methanol activity of 818.59 µmol/L.g was recorded when the CuZrIm1 catalyst with Cu/Zr/Im/NH4OH molar ratio of 2:1:4:2 (mmol/mmol/mmol/M) was employed. The enhanced yield is attributed to the presence of Cu2+ oxidation state and the uniformly dispersed active metals. The response surface methodology (RSM) was used to optimize the reaction parameters. The predicted results agreed well with the experimental ones with the correlation coefficient (R2) of 0.99. The optimization results showed that the highest methanol activity of 1054 µmol/L.g was recorded when the optimum parameters were employed, i.e., stirring rate (540 rpm), intensity of light (275 W/m2) and photocatalyst loading (1.3 g/L). The redox potential value for the CuZrIm1 shows that the reduction potential is −1.70 V and the oxidation potential is +1.28 V for the photoreduction of CO2 to methanol. The current work has established the potential utilization of the imidazolate framework as catalyst support for the photoreduction of CO2 to methanol.

scholarly journals One-step synthesis of nitrogen-grafted copper-gallic acid for enhanced methylene blue removal

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shella Permatasari Santoso ◽  
Vania Bundjaja ◽  
Artik Elisa Angkawijaya ◽  
Chintya Gunarto ◽  
Alchris Woo Go ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Gallic Acid ◽  
Synthesis Method ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Temperature Dependent ◽  
One Step ◽  
Detailed Assessment ◽  
Higher Temperature

AbstractNitrogen-grafting through the addition of glycine (Gly) was performed on a metal- phenolic network (MPN) of copper (Cu2+) and gallic acid (GA) to increase its adsorption capacity. Herein, we reported a one-step synthesis method of MPN, which was developed according to the metal–ligand complexation principle. The nitrogen grafted CuGA (Ng-CuGA) MPN was obtained by reacting Cu2+, GA, and Gly in an aqueous solution at a molar ratio of 1:1:1 and a pH of 8. Several physicochemical measurements, such as Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), N2 sorption, X-ray diffraction (XRD), and thermal gravimetry analysis (TGA), were done on Ng-CuGA to elucidate its characteristics. The analysis revealed that the Ng-CuGA has non-uniform spherical shaped morphology with a pore volume of 0.56 cc/g, a pore size of 23.25 nm, and thermal stability up to 205 °C. The applicational potential of the Ng-CuGA was determined based on its adsorption capacity against methylene blue (MB). The Ng-CuGA was able to adsorb 190.81 mg MB per g adsorbent at a pH of 6 and temperature of 30 °C, which is 1.53 times higher than the non-grafted CuGA. Detailed assessment of Ng-CuGA adsorption properties revealed their pH- and temperature-dependent nature. The adsorption capacity and affinity were found to decrease at a higher temperature, demonstrating the exothermic adsorption behavior.

scholarly journals Thermal, Structural, and Physical Properties of Freeze Dried Tropical Fruit Powder

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
K. A. Athmaselvi ◽  
C. Kumar ◽  
M. Balasubramanian ◽  
Ishita Roy
Keyword(s):  
Particle Size ◽  
Physical Properties ◽  
Average Particle Size ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Tropical Fruit ◽  
X Ray ◽  
Freeze Dried ◽  
Fruit Powder ◽  
Lcr Meter

This study evaluates the physical properties of freeze dried tropical (guava, sapota, and papaya) fruit powders. Thermal stability and weight loss were evaluated using TGA-DSC and IR, which showed pectin as the main solid constituent. LCR meter measured electrical conductivity, dielectric constant, and dielectric loss factor. Functional groups assessed by FTIR showed presence of chlorides, and O–H and N–H bonds in guava, chloride and C–H bond in papaya, and chlorides, and C=O and C–H bonds in sapota. Particle size and type of starch were evaluated by X-ray diffraction and microstructure through scanning electronic microscopy. A semicrystalline profile and average particle size of the fruit powders were evidenced by X-ray diffraction and lamellar/spherical morphologies by SEM. Presence of A-type starch was observed in all three fruits. Dependence of electric and dielectric properties on frequency and temperature was observed.

Chemical synthesis of poly(β-hydroxybutyrate) by the polymerization of (R,S)-β-butyrolactone with aluminoxane catalysts

1995 ◽  
Vol 41 (13) ◽  
pp. 274-281 ◽  
Author(s):  
Robert W. Lenz ◽  
John Yang ◽  
Bin Wu ◽  
C. Jeff Harlan ◽  
Andrew R. Barron
Keyword(s):  
Molecular Weight ◽  
Chemical Synthesis ◽  
Physical Properties ◽  
High Molecular Weight ◽  
Crystalline Polymers ◽  
Group 4 ◽  
Catalyst Systems

Racemic β-butyrolactone can be polymerized to crystalline polymers of reasonably high molecular weight by the use of aluminoxane catalysts. Investigations in this and other laboratories have shown that these polymers can be fairly highly isotactic, and in that form they are closely related in structure and physical properties to a reserve polyester produced by many bacteria: poly(β-hydroxybutyrate). In the present investigation, Ziegler–Natta type aluminoxane catalyst systems and a new aluminoxane derivative, tert-butylaluminoxane, were evaluated in attempts to polymerize racemic β-butyrolactone in higher yields to polymers of higher molecular weight and higher stereoregularity. The addition of group 4 metallocenes as cocatalysts for both methylaluminoxane and iso-butylaluminoxane catalysts gave higher yields of the isotactic polymer than those obtained with these catalysts alone, but surprisingly, the tert-butylaluminoxane catalysts produced predominantly syndiotactic rather than isotactic polymers.Key words: poly(β-hydroxybutyrate), β-butyrolactone, aluminoxane catalysts, isotactic poly(β-hydroxybutyrate), syndiotactic poly(β-hydroxybutyrate).

scholarly journals Fabrication and Physical Properties of Single-Crystalline Βeta-FeSi2 Nanowires

2020 ◽  
Vol 15 (1) ◽  
Author(s):  
Chih-Yung Yang ◽  
Shu-Meng Yang ◽  
Yu-Yang Chen ◽  
Kuo-Chang Lu
Keyword(s):  
Electron Microscopy ◽  
Physical Properties ◽  
Chemical Vapor ◽  
Chemical Vapor Deposition Method ◽  
Ferromagnetic Behavior ◽  
X Ray Diffraction ◽  
Field Emitters ◽  
Transmission Electron ◽  
Single Source Precursor ◽  
Carrier Gases

Abstract In this study, self-catalyzed β-FeSi2 nanowires, having been wanted but seldom achieved in a furnace, were synthesized via chemical vapor deposition method where the fabrication of β-FeSi2 nanowires occurred on Si (100) substrates through the decomposition of the single-source precursor of anhydrous FeCl3 powders at 750–950 °C. We carefully varied temperatures, duration time, and the flow rates of carrier gases to control and investigate the growth of the nanowires. The morphology of the β-FeSi2 nanowires was observed with scanning electron microscopy (SEM), while the structure of them was analyzed with X-ray diffraction (XRD) and transmission electron microscopy (TEM). The growth mechanism has been proposed and the physical properties of the iron disilicide nanowires were measured as well. In terms of the magnetization of β-FeSi2, nanowires were found to be different from bulk and thin film; additionally, longer β-FeSi2 nanowires possessed better magnetic properties, showing the room-temperature ferromagnetic behavior. Field emission measurements demonstrate that β-FeSi2 nanowires can be applied in field emitters.

Self Assembling Nanostructured Delivery Vehicles for Biochemically Reactive Pairs

1994 ◽  
Vol 351 ◽  
Author(s):  
Nir Kossovsky ◽  
A. Gelman ◽  
H.J. Hnatyszyn ◽  
E. Sponsler ◽  
G.-M. Chow
Keyword(s):  
Physical Properties ◽  
Self Assembly ◽  
Materials Science ◽  
Technology Development ◽  
Biological Behavior ◽  
X Ray Diffraction ◽  
Self Assembling ◽  
Transmission Electron ◽  
Carbon Ceramic

ABSTRACTIntrigued by the deceptive simplicity and beauty of macromolecular self-assembly, our laboratory began studying models of self-assembly using solids, glasses, and colloidal substrates. These studies have defined a fundamental new colloidal material for supporting members of a biochemically reactive pair.The technology, a molecular transportation assembly, is based on preformed carbon ceramic nanoparticles and self assembled calcium-phosphate dihydrate particles to which glassy carbohydrates are then applied as a nanometer thick surface coating. This carbohydrate coated core functions as a dehydroprotectant and stabilizes surface immobilized members of a biochemically reactive pair. The final product, therefore, consists of three layers. The core is comprised of the ceramic, the second layer is the dehydroprotectant carbohydrate adhesive, and the surface layer is the biochemically reactive molecule for which delivery is desired.We have characterized many of the physical properties of this system and have evaluated the utility of this delivery technology in vitro and in animal models. Physical characterization has included standard and high resolution transmission electron microscopy, electron and x-ray diffraction and ζ potential analysis. Functional assays of the ability of the system to act as a nanoscale dehydroprotecting delivery vehicle have been performed on viral antigens, hemoglobin, and insulin. By all measures at present, the favorable physical properties and biological behavior of the molecular transportation assembly point to an exciting new interdisciplinary area of technology development in materials science, chemistry and biology.

Application of vermiculite and limestone to desulphurization and to the removal of dust during briquette combustion

2003 ◽  
Vol 67 (6) ◽  
pp. 1243-1251 ◽  
Author(s):  
A. Lu ◽  
D. Zhao ◽  
J. Li ◽  
C. Wang ◽  
S. Qin
Keyword(s):  
Electron Microscopy ◽  
Coal Combustion ◽  
Combustion Temperature ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Retention Ratio ◽  
X Ray ◽  
Major Factors ◽  
Chemical Reactant ◽  
Scanning Electron

AbstractSmall domestic cooking furnaces are widely used in China. These cooking furnaces release SO2 gas and dust into the atmosphere and cause serious air pollution. Experiments were conducted to investigate the effects of vermiculite, limestone or CaCO3, and combustion temperature and time on desulphurization and dust removal during briquette combustion in small domestic cooking furnaces. Additives used in the coal are vermiculite, CaCO3 and bentonite. Vermiculite is used for its expansion property to improve the contact between CaCO3 and SO2 and to convey O2 into the interior of briquette; CaCO3 is used as a chemical reactant to react with SO2 to form CaSO4; and bentonite is used to develop briquette strength. Expansion of vermiculite develops loose interior structures, such as pores or cracks, inside the briquette, and thus brings enough oxygen for combustion and sulphation reaction. Effective combustion of the original carbon reduces amounts of dust in the fly ash. X-ray diffraction, optical microscopy, and scanning electron microscopy with energy dispersive X-ray analysis show that S exists in the ash only as anhydrite CaSO4, a product of SO2 reacting with CaCO3 and O2. The formation of CaSO4 effectively reduces or eliminates SO2 emission from coal combustion. The major factors controlling S retention are vermiculite, CaCO3 and combustion temperature. The S retention ratio increases with increasing vermiculite amount at 950°C. The S retention ratio also increases with increasing Ca/S molar ratio, and the best Ca/S ratio is 2-3 for most combustion. With 12 g of the original coal, 1 to 2 g of vermiculite, a molar Ca/S ratio of 2.55 by adding CaCO3, and some bentonite, a S retention ratio >65% can be readily achieved. The highest S retention ratio of 97.9% is achieved at 950°C with addition of 2 g of vermiculite, a Ca/S ratio of 2.55 and bentonite.

Sign in / Sign up

Export Citation Format

Share Document