Specialty Elastomers for Automotive Applications

1998 ◽  
Vol 71 (3) ◽  
pp. 449-519 ◽  
Author(s):  
Kinro Hashimoto ◽  
Akio Maeda ◽  
Kiyoshi Hosoya ◽  
Yoshihiro Todani
Keyword(s):  
Automotive Industry ◽  
High Performance ◽  
Chemical Properties ◽  
Polymeric Materials ◽  
Low Permeability ◽  
Automotive Applications ◽  
Gasoline Engines ◽  
Automotive Components ◽  
Automotive Parts ◽  
The Many

Abstract Various elastomers are used for automotive components because of their physical properties, chemical properties, durability, etc. There are belts to transmit energy, seals to support radial or reciprocating parts, gaskets and O-rings to seal in oils and fuels, hoses to deliver liquid and gases and diaphragms to control them. Figure 1 shows one example of elastomers for gasoline engines reported by Akema and Yoshida. Rubbers are soft polymeric materials having generally 100 MPa of Young's modulus (shown in Figure 2) for the normally applied temperature range. They are widely used for the buffer position between high modulus materials such as metals, plastics, glasses, etc., in energy transmission, liquid delivery, and energy isolation positions. The materials are selected for their resistance to fuels, oils, and heat; as well as their cold flexibility and sealing ability. However, different materials are sometimes selected for the same device depending upon such factors as applied temperature, class of fuels and oils, and the engineering design of the car. The many problems confronting the automotive industry these days are shown in Table A-I. They are roughly classified into two areas: environmental and safety. Elastomers for automotive applications have been changing to solve many kinds of problems. Table A-II shows the trends of rubber materials being used for automotive parts. High performance rubbers, which have heat resistance, long life, low permeability, good abrasion resistance, and so on, are all being adopted.

Composites and Reinforced Plastics in the Automotive Industry

2014 ◽  
Vol 611 ◽  
pp. 352-357 ◽  
Author(s):  
Karol Bielefeldt ◽  
Janusz Walkowiak ◽  
Władysław Papacz
Keyword(s):  
Automotive Industry ◽  
Polymeric Materials ◽  
Hybrid Structures ◽  
Reinforced Plastics ◽  
Automotive Parts

The paper presents the possibility of using polymeric materials in the automotive industry. Some of the requirements for materials have been discussed and the possibilities of a significant increase in strength of the materials by the use of reinforcements have been indicated. Numerous examples of applications of reinforced plastics as automotive parts have been presented. Some of the latest technologies that enable the production of automotive parts from reinforced plastics, including hybrid structures, have been described.

A Recommender System for Inverse Design of Polycarbonates and Polyesters

2020 ◽  
Author(s):  
Nathaniel Park ◽  
Dmitry Yu. Zubarev ◽  
James L. Hedrick ◽  
Vivien Kiyek ◽  
Christiaan Corbet ◽  
...  
Keyword(s):  
Ring Opening ◽  
High Performance ◽  
Recommendation System ◽  
Polymeric Materials ◽  
Monomer Conversion ◽  
Design Strategy ◽  
Ring Opening Polymerization ◽  
Inverse Design ◽  
False Negatives ◽  
Accelerate Development

The convergence of artificial intelligence and machine learning with material science holds significant promise to rapidly accelerate development timelines of new high-performance polymeric materials. Within this context, we report an inverse design strategy for polycarbonate and polyester discovery based on a recommendation system that proposes polymerization experiments that are likely to produce materials with targeted properties. Following recommendations of the system driven by the historical ring-opening polymerization results, we carried out experiments targeting specific ranges of monomer conversion and dispersity of the polymers obtained from cyclic lactones and carbonates. The results of the experiments were in close agreement with the recommendation targets with few false negatives or positives obtained for each class.<br>

Content and composition of phospholipids, fatty acids and sterols in commercial natural phospholipid excipients

2020 ◽  
Vol 16 ◽  
Author(s):  
Luxia Zheng ◽  
Xiong Shen ◽  
Yingchun Wang ◽  
Jian Liang ◽  
Mingming Xu ◽  
...  
Keyword(s):  
Fatty Acids ◽  
Cluster Analysis ◽  
Fatty Acid ◽  
High Performance ◽  
Comprehensive Evaluation ◽  
Phospholipid Fatty Acid ◽  
Egg Yolk ◽  
Systematic Research ◽  
Manufacturing Enterprises ◽  
The Many

Background: Phospholipids are widely used in food and pharmaceutical industry as functional excipients. In spite of the many analytical methods reported, there are very limited reports concerning systematic research and comparison of phospholipid excipients. Objective: To present a comprehensive evaluation of commercial natural phospholipid excipients (CNPEs). Methods: Seventeen batches of CNPEs from five manufacturing enterprises, isolated either from soybean or egg yolk, were investigated. The content and composition of phospholipids, fatty acids and sterols as a whole were considered as the evaluative index of CNPEs. Eight kinds of phospholipids were determined by supercritical fluid chromatography (SFC), twenty-one kinds of fatty acids were determined by gas chromatography (GC) after boron trifluoride-methanol derivatization, and nine kinds of sterols were determined by high performance liquid chromatography (HPLC) after separation and derivatization of the unsaponifiable matter. Cluster analysis was employed for classification and identification of the CNPEs. Results: The results showed that each kind of CNPEs had its characteristic content and composition of phospholipids, fatty acids and sterols. Seventeen batches of samples were divided into eight groups in cluster analysis. CNPEs of the same type from different source (soybean or egg yolk) or enterprises presented different content and composition of phospholipids, fatty acids and sterols. Conclusion: Each type of CNPEs had its characteristic content and composition of phospholipid, fatty acid and sterol. The compositions of phospholipid, fatty acid and sterol as a whole can be applied as an indicator of the quality and characteristics for CNPEs.

scholarly journals DESIGNING AN EXPERIMENT FOR EVALUATING SEATING POSITIONS IN PARALYMPIC ROWING

2020 ◽  
Vol 1 ◽  
pp. 2485-2494
Author(s):  
S. W. Eikevåg ◽  
A. Kvam ◽  
M. K. Bjølseth ◽  
J. F. Erichsen ◽  
M. Steinert
Keyword(s):  
High Performance ◽  
Substantial Impact ◽  
Rowing Performance ◽  
Rowing Ergometer ◽  
Design Challenge ◽  
The Many ◽  
Seating Position

AbstractWhen designing high performance sports equipment for Paralympic athletes, there are many unknowns for the design engineer to consider. The design challenge is an optimisation task per individual athlete. However, modelling this optimisation is difficult due to the many variables. This article presents the design of an experiment for identifying and evaluating various seating positions in Paralympic rowing by using a rowing ergometer with a modified seat. Results indicate that changing seating position has a substantial impact on per-athlete rowing performance.

scholarly journals Recent Developments in Lignin- and Tannin-Based Non-Isocyanate Polyurethane Resins for Wood Adhesives—A Review

2021 ◽  
Vol 11 (9) ◽  
pp. 4242
Author(s):  
Manggar Arum Aristri ◽  
Muhammad Adly Rahandi Lubis ◽  
Sumit Manohar Yadav ◽  
Petar Antov ◽  
Antonios N. Papadopoulos ◽  
...  
Keyword(s):  
Automotive Industry ◽  
Polymeric Materials ◽  
Review Article ◽  
Future Perspectives ◽  
Wood Adhesives ◽  
Adhesion Properties ◽  
Lighting Industry ◽  
Renewable Natural Resources ◽  
Recent Developments ◽  
Strong Adhesion

This review article aims to summarize the potential of using renewable natural resources, such as lignin and tannin, in the preparation of NIPUs for wood adhesives. Polyurethanes (PUs) are extremely versatile polymeric materials, which have been widely used in numerous applications, e.g., packaging, footwear, construction, the automotive industry, the lighting industry, insulation panels, bedding, furniture, metallurgy, sealants, coatings, foams, and wood adhesives. The isocyanate-based PUs exhibit strong adhesion properties, excellent flexibility, and durability, but they lack renewability. Therefore, this study focused on the development of non-isocyanate polyurethane lignin and tannin resins for wood adhesives. PUs are commercially synthesized using polyols and polyisocyanates. Isocyanates are toxic, costly, and not renewable; thus, a search of suitable alternatives in the synthesis of polyurethane resins is needed. The reaction with diamine compounds could result in NIPUs based on lignin and tannin. The research on bio-based components for PU synthesis confirmed that they have good characteristics as an alternative for the petroleum-based adhesives. The advantages of improved strength, low curing temperatures, shorter pressing times, and isocyanate-free properties were demonstrated by lignin- and tannin-based NIPUs. The elimination of isocyanate, associated with environmental and human health hazards, NIPU synthesis, and its properties and applications, including wood adhesives, are reported comprehensively in this paper. The future perspectives of NIPUs’ production and application were also outlined.

scholarly journals Additive Manufacturing of Sensors for Military Monitoring Applications

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1455
Author(s):  
David T. Bird ◽  
Nuggehalli M. Ravindra
Keyword(s):  
Additive Manufacturing ◽  
High Performance ◽  
Sensor Technology ◽  
Distinct Advantage ◽  
Industrial Sectors ◽  
Sensor Fabrication ◽  
The Us ◽  
3D Printed ◽  
Maximum Protection ◽  
The Many

The US Department of Defense (DoD) realizes the many uses of additive manufacturing (AM) as it has become a common fabrication technique for an extensive range of engineering components in several industrial sectors. 3D Printed (3DP) sensor technology offers high-performance features as a way to track individual warfighters on the battlefield, offering protection from threats such as weaponized toxins, bacteria or virus, with real-time monitoring of physiological events, advanced diagnostics, and connected feedback. Maximum protection of the warfighter gives a distinct advantage over adversaries by providing an enhanced awareness of situational threats on the battle field. There is a need to further explore aspects of AM such as higher printing resolution and efficiency, with faster print times and higher performance, sensitivity and optimized fabrication to ensure that soldiers are more safe and lethal to win our nation’s wars and come home safely. A review and comparison of various 3DP techniques for sensor fabrication is presented.

scholarly journals Direct Patterning and Spontaneous Self-Assembly of Graphene Oxide via Electrohydrodynamic Jet Printing for Energy Storage and Sensing

Micromachines ◽  
2019 ◽  
Vol 11 (1) ◽  
pp. 13 ◽  
Author(s):  
Bin Zhang ◽  
Jaehyun Lee ◽  
Mincheol Kim ◽  
Naeeung Lee ◽  
Hyungdong Lee ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Energy Storage ◽  
Self Assembly ◽  
High Performance ◽  
Three Dimensional ◽  
Chemical Properties ◽  
Layer By Layer ◽  
Energy Storage Devices ◽  
Laminar Structure ◽  
Jet Printing

The macroscopic assembly of two-dimensional materials into a laminar structure has received considerable attention because it improves both the mechanical and chemical properties of the original materials. However, conventional manufacturing methods have certain limitations in that they require a high temperature process, use toxic solvents, and are considerably time consuming. Here, we present a new system for the self-assembly of layer-by-layer (LBL) graphene oxide (GO) via an electrohydrodynamic (EHD) jet printing technique. During printing, the orientation of GO flakes can be controlled by the velocity distribution of liquid jet and electric field-induced alignment spontaneously. Closely-packed GO patterns with an ordered laminar structure can be rapidly realized using an interfacial assembly process on the substrates. The surface roughness and electrical conductivity of the LBL structure were significantly improved compared with conventional dispensing methods. We further applied this technique to fabricate a reduced graphene oxide (r-GO)-based supercapacitor and a three-dimensional (3D) metallic grid hybrid ammonia sensor. We present the EHD-assisted assembly of laminar r-GO structures as a new platform for preparing high-performance energy storage devices and sensors.

Molecular materials for micro-electronics

2000 ◽  
Vol 78 (3) ◽  
pp. 231-241 ◽  
Author(s):  
M D'Iorio
Keyword(s):  
High Performance ◽  
Organic Materials ◽  
Coming Of Age ◽  
Polymeric Materials ◽  
Organic Light Emitting Diodes ◽  
Light Emitting ◽  
Light Emitting Devices ◽  
Plastic Electronics ◽  
Organic Light ◽  
Recent Developments

Molecular organic materials have had an illustrious past but the ability to deposit these as homogeneous thin films has rejuvenated the field and led to organic light-emitting diodes (OLEDs) and the development of an increasing number of high-performance polymers for nonlinear and electronic applications. Whereas the use of organic materials in micro-electronics was restricted to photoresists for patterning purposes, polymeric materials are coming of age as metallic interconnects, flexible substrates, insulators, and semiconductors in all-plastic electronics. The focus of this topical review will be on organic light-emitting devices with a discussion of the most recent developments in electronic devices.PACS Nos.: 85.60Jb, 78.60Fi, 78.55Kz, 78.66Qn, 73.61Ph, 72.80Le

Development and Achievements of SSM Processes for High Performance Components

2016 ◽  
Vol 256 ◽  
pp. 319-327 ◽  
Author(s):  
Mario Rosso ◽  
Ildiko Peter ◽  
Ivano Gattelli
Keyword(s):  
Industrial Development ◽  
High Performance ◽  
Rear Axle ◽  
Research Work ◽  
Industrial Applications ◽  
Alternative Methods ◽  
Front Suspension ◽  
Large Numbers ◽  
Automotive Parts ◽  
High Level

During the last decades under the enthusiastic and competent guidance of Mr Chiarmetta SSM processes attained in Italy at Stampal Spa (Torino) an unquestionable high level of industrial development with the production of large numbers of high performance automotive parts, like variety of suspension support, engine suspension mounts, steering knuckle, front suspension wheel, arm and rear axle. Among the most highlighted findings SSM processes demonstrated their capability to reduce the existing gap between casting and forging, moreover during such a processes there are the opportunity to better control the defect level.Purpose of this paper is to highlight the research work and the SSM industrial production attained and developed by Mr G.L. Chiarmetta, as well as to give an overview concerning some alternative methods for the production of enhanced performance light alloys components for critical industrial applications and to present an analysis of a new rheocasting process suitable for the manufacturing of high performance industrial components.

Sign in / Sign up

Export Citation Format

Share Document