Cut Growth in Vulcanizates of Natural Rubber, cis-Polybutadiene, and a 50/50 Blend during Single and Repeated Extension

1996 ◽  
Vol 69 (5) ◽  
pp. 807-818 ◽  
Author(s):  
G. R. Hamed ◽  
H. J. Kim ◽  
A. N. Gent
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Crack Tip ◽  
Forward Direction ◽  
Secondary Crack ◽  
Abrupt Decrease ◽  
Considerable Distance ◽  
Secondary Cracks ◽  
Cut Depth ◽  
Longitudinal Cracks

Abstract A typical passenger sidewall composition was employed using three elastomer systems NR, BR, and a 50/50 blend of NR and BR. Tensile strips with edge cuts of various depths were strained in two ways continuously increasing extension up to rupture, or repeatedly stretching them to progressively higher strains until failure occurred. For BR, the tensile strength σb decreased steadily with increasing cut depth, c, while NR and NR/BR showed an abrupt decrease in σb at a critical cut size, ccr. This is attributed to crystallization of NR throughout the specimen at high strains, when c<ccr, while crystallization is confined to the crack tip region when c>ccr. Furthermore, in samples of NR and NR/ BR the crack tip split, forming two secondary cracks which grew a considerable distance parallel to the direction of straining, and even turned backwards, before stopping. Rupture of the specimen did not occur until a new (third) crack was initiated from the smooth torn surface of the secondary crack. Under repeated straining NR specimens developed secondary cracks repeatedly in a characteristic alternating pattern. These are instances of severe “knotty” tearing. In contrast, in BR samples the initial cut always grew in a forward direction and secondary, longitudinal cracks did not develop.

Effect of Carbon Black Concentration on Cut Growth in NR Vulcanizates

2003 ◽  
Vol 76 (2) ◽  
pp. 436-460 ◽  
Author(s):  
G. R. Hamed ◽  
A. A. Al-Sheneper
Keyword(s):  
Stress Concentration ◽  
Carbon Black ◽  
Natural Rubber ◽  
Single Crack ◽  
Carbon Black Concentration ◽  
Low Levels ◽  
Cut Depth ◽  
Longitudinal Cracks

Abstract Dumbbell specimens containing edge razor-cuts of various depths, c, have been prepared from sulfur-vulcanized natural rubber compositions containing 0–75 phr of N115 black. Normal tensile strengths (c=0) of the gum and all black-filled samples are similar. However, cut growth resistance (CGR) relative to the gum, depends strongly on black content and cut depth. With about 6–15 phr of black, filled specimens are weaker than the gum and fracture occurs by simple forward growth of the original cut tip, i.e., a single crack develops and propagates laterally. At about 18 phr of black, filled specimens become stronger than the gum and cracking becomes complex. Prior to catastrophic rupture, crack splitting occurs near the original cut tip - forming at least two slowly-growing, longitudinal cracks. These reduce the stress concentration caused by the cut, thereby delaying rupture, and marking the onset of “reinforcement”. All pre-cut specimens containing 18–75 phr of black are stronger than the gum and they exhibit crack splitting. Specimens containing 50 phr of black have the highest strength - being about ten times as strong as the gum when cuts are large. The decrease in CGR at low levels of black and increase at high levels is attributed to competing effects upon the addition of carbon black to NR.

Tensile Strength of Protein-free Natural Rubber and its Vulcanizate Soaked in Water

2020 ◽  
Vol 93 (9) ◽  
pp. 293-299
Author(s):  
Luu Thanh HUYEN ◽  
Chen Ao RAN ◽  
Yoshimasa YAMAMOTO ◽  
Seiichi KAWAHARA
Keyword(s):  
Tensile Strength ◽  
Natural Rubber

Pengaruh penambahan natural rubber (NR), epoxidation natural rubber (ENR-46) dan chlorprene rubber (CR) pada sifat kompon termoplastik

2020 ◽  
Vol 26 (2) ◽  
pp. 62-69
Author(s):  
Farida Ali ◽  
Tuti I. Sari ◽  
Andi A. Siahaan ◽  
Al-Kautsar D. Arya ◽  
Tri Susanto
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Vinyl Chloride ◽  
Butadiene Rubber ◽  
Elongation At Break ◽  
Nitrile Butadiene Rubber ◽  
Poly Vinyl Chloride

Penelitian ini untuk mengetahui pengaruh penambahan Natural Rubber (NR) dan Epoxidation Natural Rubber (ENR-46) dengan kompatibiliser Chlorprene Rubber (CR) pada aplikasi kompon termoplastik Poly Vinyl Chloride (PVC) dan Nitrile Butadiene Rubber (NBR), variabel penelitian meliputi ENR-46/PVC/NBR/CR, NR/PVC/NBR/CR dan CR-NR/PVC/NBR, CR-ENR-46/PVC/NBR. Parameter pengujian sifat fisik-mekanik : Hardness (Shore A), Tensile Strength (Mpa), Elongation at Break (%) dan ketahanan terhadap pelarut minyak (n-Pentane, Toluene, Hexane dan Pertalite). Hasil penelitian didapatkan untuk sifat fisik-mekanik, semakin banyak penambahan NR Kekerasan kompon termoplastik akan menurun, Tensile Strength dan Elongation at Break kompon akan meningkat begitu juga dengan CR-NR. Tetapi berbanding terbalik hasilnya untuk ENR-46 dan CR-ENR-46. Pengujian Ketahanan terhadap pelarut minyak semakin banyak penambahan ENR-46 Ketahanan kompon termoplastik terhadap pelarut akan meningkat, hasil yang sama juga pada CR-ENR-46. Tetapi berbanding terbalik hasilnya dengan penambahan NR dan CR-NR pada kompon termoplastik.

EFFECT OF ZINC DITHIOCARBAMATES AND THIAZOLE-BASED ACCELERATORS ON THE VULCANIZATION OF NATURAL RUBBER

2012 ◽  
Vol 85 (1) ◽  
pp. 120-131 ◽  
Author(s):  
Md. Najib Alam ◽  
Swapan Kumar Mandal ◽  
Subhas Chandra Debnath
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Performance Liquid Chromatography ◽  
Liquid Chromatography ◽  
Reaction Mechanism ◽  
Natural Rubber ◽  
High Performance ◽  
Binary Systems ◽  
Synergistic Activity ◽  
Tetramethylthiuram Disulfide

Abstract Several zinc dithiocarbamates (ZDCs) as accelerator derived from safe amine has been exclusively studied in the presence of thiazole-based accelerators to introduce safe dithiocarbamate in the vulcanization of natural rubber. Comparison has been made between conventional unsafe zinc dimethyldithiocarbamate (ZDMC) with safe novel ZDC combined with thizole-based accelerators in the light of mechanical properties. The study reveals that thiuram disulfide and 2-mercaptobenzothiazole (MBT) are always formed from the reaction either between ZDC and dibenzothiazyledisulfide (MBTS) or between ZDC and N-cyclohexyl-2-benzothiazole sulfenamide (CBS). It has been conclusively proved that MBT generated from MBTS or CBS reacts with ZDC and produces tetramethylthiuram disulfide. The observed synergistic activity has been discussed based on the cure and physical data and explained through the results based on high-performance liquid chromatography and a reaction mechanism. Synergistic activity is observed in all binary systems studied. The highest tensile strength is observed in the zinc (N-benzyl piperazino) dithiocarbamate-accelerated system at 3:6 mM ratios. In respect of tensile strength and modulus value, unsafe ZDMC can be successfully replaced by safe ZDCs in combination with thiazole group containing accelerator.

scholarly journals Biocomposites of Epoxidized Natural Rubber/Poly(lactic acid) Modified with Natural Fillers (Part I)

2021 ◽  
Vol 22 (6) ◽  
pp. 3150
Author(s):  
Anna Masek ◽  
Stefan Cichosz ◽  
Małgorzata Piotrowska
Keyword(s):  
Tensile Strength ◽  
Lactic Acid ◽  
Natural Rubber ◽  
Epoxidized Natural Rubber ◽  
Poly Lactic Acid ◽  
Uv Aging ◽  
High Elasticity ◽  
Natural Fillers ◽  
Natural Additives

The study aimed to prepare sustainable and degradable elastic blends of epoxidized natural rubber (ENR) with poly(lactic acid) (PLA) that were reinforced with flax fiber (FF) and montmorillonite (MMT), simultaneously filling the gap in the literature regarding the PLA-containing polymer blends filled with natural additives. The performed study reveals that FF incorporation into ENR/PLA blend may cause a significant improvement in tensile strength from (10 ± 1) MPa for the reference material to (19 ± 2) MPa for the fibers-filled blend. Additionally, it was found that MMT employment in the role of the filler might contribute to ENR/PLA plasticization and considerably promote the blend elongation up to 600%. This proves the successful creation of the unique and eco-friendly PLA-containing polymer blend exhibiting high elasticity. Moreover, thanks to the performed accelerated thermo-oxidative and ultraviolet (UV) aging, it was established that MMT incorporation may delay the degradation of ENR/PLA blends under the abovementioned conditions. Additionally, mold tests revealed that plant-derived fiber addition might highly enhance the ENR/PLA blend’s biodeterioration potential enabling faster and more efficient growth of microorganisms. Therefore, materials presented in this research may become competitive and eco-friendly alternatives to commonly utilized petro-based polymeric products.

scholarly journals Composites from Thermoplastic Natural Rubber Reinforced Rubberwood Sawdust: Effects of Sawdust Size and Content on Thermal, Physical, and Mechanical Properties

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Chatree Homkhiew ◽  
Surasit Rawangwong ◽  
Worapong Boonchouytan ◽  
Wiriya Thongruang ◽  
Thanate Ratanawilai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
High Density Polyethylene ◽  
High Performance ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Shore Hardness ◽  
Thermoplastic Natural Rubber ◽  
Plastic Content

The aim of this work is to investigate the effects of rubberwood sawdust (RWS) size and content as well as the ratio of natural rubber (NR)/high-density polyethylene (HDPE) blend on properties of RWS reinforced thermoplastic natural rubber (TPNR) composites. The addition of RWS about 30–50 wt% improved the modulus of the rupture and tensile strength of TPNR composites blending with NR/HDPE ratios of 60/40 and 50/50. TPNR composites reinforced with RWS 80 mesh yielded better tensile strength and modulus of rupture than the composites with RWS 40 mesh. The TPNR/RWS composites with larger HDPE content gave higher tensile, flexural, and Shore hardness properties and thermal stability as well as lower water absorption. The TPNR/RWS composites with larger plastic content were therefore suggested for applications requiring high performance of thermal, physical, and mechanical properties.

scholarly journals An experimental method to determine the intralaminar fracture toughness of high-strength carbon-fibre reinforced composite aerostructures

2018 ◽  
Vol 122 (1255) ◽  
pp. 1352-1370 ◽  
Author(s):  
H. Liu ◽  
B.G. Falzon ◽  
G. Catalanotti ◽  
W. Tan
Keyword(s):  
Fracture Toughness ◽  
Tensile Strength ◽  
Crack Tip ◽  
Damage Mechanism ◽  
Calibration Method ◽  
Compact Tension ◽  
Tensile Fracture ◽  
High Tensile Strength ◽  
Physical Test ◽  
Area Method

ABSTRACTCarbon fibres with high tensile strength are being increasingly utilised in the manufacture of advanced composite aerostructures. A Modified Compact Tension (MCT) specimen is often deployed to measure the longitudinal intralaminar fracture toughness but a high tensile strength often leads to premature damage away from the crack tip. We present an approach whereby the MCT specimen is supported by external fixtures to prevent premature damage. In addition, we have developed a novel measurement technique, based on the fibre failure strain and C-scanning, to determine the crack length in the presence of surface sublaminate delamination which masks the crack tip location. A set of cross-ply specimens, with a ((90/0)s)4 layup, were manufactured from an IMS60/epoxy composite system Two different data reduction schemes, compliance calibration and the area method, are used to determine the fibre-dominated initiation and propagation intralaminar fracture toughness values. Propagation values of fracture toughness were measured at 774.9 ± 5.2% kJ/m2 and 768.5 ± 4.1% kJ/m2, when using the compliance calibration method and the area method, respectively. Scanning Electron Microscopy (SEM) is carried out on the fracture surface to obtain insight into the damage mechanism of high-tensile-strength fibre-reinforced unidirectional composites. The measured tensile fracture toughness value is used in a fully validated computational model to simulate the physical test.

Graft Polymers Derived from Natural Rubber

1956 ◽  
Vol 29 (1) ◽  
pp. 99-105 ◽  
Author(s):  
G. F. Bloomfield ◽  
F. M. Merrett ◽  
F. J. Popham ◽  
P. Mc L. Swift
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Methyl Methacrylate ◽  
Transfer Reaction ◽  
Polymer Chains ◽  
Vinyl Monomers ◽  
Grafted Polymer ◽  
Polymeric Chains ◽  
Graft Polymers ◽  
Direct Growth

Abstract Graft polymers result when vinyl monomers are polymerized in the presence of natural rubber, either in solution or as latex, and some of the polymeric chains become attached to the rubber molecules. The properties of the natural rubber can be widely modified according to the nature and the amount of the grafted polymer. The polymer-modified natural rubber appears to be produced by direct growth of polymer chains on to rubber molecules rather than by a transfer reaction involving the rubber. Graft polymers of styrene and methyl methacrylate with natural rubber can be compounded and cured to give light-colored articles of good tensile strength, and rubber-methyl methacrylate graft polymers have outstanding flex-cracking and fatigue resistance.

Tensile Behavior after Oxidative Aging of Gum and Black-Filled Vulcanizates of SBR and NR

1999 ◽  
Vol 72 (4) ◽  
pp. 721-730 ◽  
Author(s):  
G. R. Hamed ◽  
J. Zhao
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Tensile Behavior ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Oxidative Aging ◽  
Prolonged Aging ◽  
Aging Period ◽  
Early Aging ◽  
Styrene Butadiene

Abstract Typical sulfur-cured vulcanizates of styrene-butadiene rubber (SBR) and natural rubber (NR) were prepared, and subjected to air-oven aging at 100 °C. Gum specimens exhibited an initial aging period in which stiffness was unchanged, while tensile strength and strain-to-break were significantly reduced. In contrast, black-filled vulcanizates stiffened during early aging. After intermediate aging times, NR specimens softened, while SBR stiffened. With prolonged aging, all compositions became hard and inextensible.

Research on Mechanical Properties of Modified Organic Montmorillonite Reinforced Nature Rubber(NR) Composites

2011 ◽  
Vol 239-242 ◽  
pp. 3231-3235
Author(s):  
Xiao Yu Zheng ◽  
Jin Cheng Wang ◽  
Ke Yang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Oh Groups ◽  
Abrasion Loss ◽  
Organic Montmorillonite ◽  
Reinforcing Agent

In this paper, hyperbranched organic montmorillonite (H-OMMT) with hydroxyl (-OH) groups was prepared. The organic montmorillonite (OMMT) was used as a reinforcing agent in NR matrix. The H-OMMT modified natural rubber (NR) had good mechanical properties with the addition of the H-OMMT. Properties, such as tensile strength and abrasion loss, were researched and compared. Results showed that NR/H-OMMT-5% composite had the best tensile and were resistant properties.

Sign in / Sign up

Export Citation Format

Share Document