Ground Rubber Tire / Thermoplastic Composites: Effect of Different Ground Rubber Tires

1993 ◽  
Vol 66 (4) ◽  
pp. 664-677 ◽  
Author(s):  
P. Rajalingam ◽  
J. Sharpe ◽  
W. E. Baker
Keyword(s):  
Particle Size ◽  
Impact Energy ◽  
Surface Oxidation ◽  
Surface Concentration ◽  
Thermoplastic Composites ◽  
Beam Radiation ◽  
Rubber Tire ◽  
Ground Rubber ◽  
Surface Modification Techniques ◽  
The Impact

Abstract Thermoplastic composites containing different Ground Rubber Tire (GRT) materials, Linear Low Density Polyethylene (LLDPE) and, in some case, a coupling agent (IB‘E’, an ethylene glycidyl methacrylate copolymer) were prepared by melt blending. The impact energies of all the thermoplastic composites (normally containing 40 wt % GRT) were evaluated using an instrumented impact tester. The effects of the GRT particle-size, particle size distribution and shape, the mode of grinding, and the oxygen surface concentration were analyzed. The wet-ambient-ground GRT based composites show higher surface oxidation and give better impact energy than cryo-ground and normal air-ground GRT based composites. Smaller GRT particle size results in a small increase in the impact property of the composite and a greater influence on the melt processability of the composites. Of the different GRT surface modification techniques studied for improved composite interfacial adhesion and impact properties the composites from electron beam radiation treated GRT yield higher increases in impact energy in comparison to corona and plasma treated GRT based composites.

The Role of Functional Polymers in Ground Rubber Tire-Polyethylene Composite

1992 ◽  
Vol 65 (5) ◽  
pp. 908-916 ◽  
Author(s):  
P. Rajalingam ◽  
W. E. Baker
Keyword(s):  
Impact Energy ◽  
Functional Polymers ◽  
Thermoplastic Composites ◽  
Polyethylene Matrix ◽  
Polyethylene Composite ◽  
Rubber Tire ◽  
Ground Rubber ◽  
Percent Improvement ◽  
The Impact

Abstract The impact energies of different polyethylene-ground rubber tire (GRT) composites were investigated. All the thermoplastic composites were prepared on a Haake Buchler batch mixer and injection molded test specimens were tested on Rheometrics drop weight instrumented impact tester. Addition of small amounts of functional polymers increases the impact energy of the polyethylene-GRT composite as much as 60%. The percent improvement in the impact energy for linear low density polyethylene (LLDPE) and the composites prepared from them is greater than for the corresponding high density polyethylene (HDPE) composites. Precoating of GRT particles with ethylene-acrylic acid (EAA) copolymers improves the impact energy of the composite, whereas precoating with the other functional polymers does not. An attempt has been made to identify the role of the functional polymers as to whether they act as toughening agents for the polyethylene matrix or coupling agent at the polyethylene-GRT interface. The results show the increase in impact energy resulting from the addition of styrene block copolymers is due to toughening of the polyethylene matrix while the reactive ethylene copolymers increase the impact energy by a coupling action with GRT.

scholarly journals Particle Impact Energy Variation with the Size and Number of Particles in a Planetary Ball Mill

2021 ◽  
Vol 333 ◽  
pp. 02016
Author(s):  
Fumie Hirosawa ◽  
Tomohiro Iwasaki ◽  
Masashi Iwata
Keyword(s):  
Particle Size ◽  
Impact Energy ◽  
Ball Mill ◽  
Mechanical Energy ◽  
Planetary Ball Mill ◽  
Particle Impact ◽  
Particle Collisions ◽  
Grinding Balls ◽  
The Impact ◽  
Number Of Particles

To investigate the mechanical energy applying to the particles in a grinding process using a planetary ball mill, the impact energy of particles was estimated by simulating the behavior of the particles and grinding balls using the discrete element method (DEM) under different conditions of the size and number of particles, corresponding to their variations during milling. As the impact energy contributing to the particle breakage, we focused on the particle impact energy generated at particle-to-grinding ball/wall and particle-to-particle collisions. The particle size and the number of particles affected the level of particle impact energy at a single collision and the number of collisions of particles, respectively, resulting in an increase of the total impact energy of particles with decreasing particle size and increasing number of particles. The result suggests that milling conditions such as the size of grinding balls should be adjusted appropriately based on the variation of the size and number of particles so that the particles can receive large amounts of the impact energy during milling.

scholarly journals The effects of gravel cushion particle size and thickness on the coefficient of restitution in rockfall impacts

2018 ◽  
Vol 18 (6) ◽  
pp. 1811-1823 ◽  
Author(s):  
Chun Zhu ◽  
Dongsheng Wang ◽  
Xing Xia ◽  
Zhigang Tao ◽  
Manchao He ◽  
...  
Keyword(s):  
Particle Size ◽  
Impact Energy ◽  
Coefficient Of Restitution ◽  
Open Pit ◽  
Test Results ◽  
Drop Tests ◽  
Damage Depth ◽  
The Stability ◽  
Energy Absorbing ◽  
The Impact

Abstract. Gravel cushions are widely used to absorb the impact energy of falling rocks in open-pit mines. A particularly important application is to enhance the energy-absorbing capacity of rockfall sheds. In this paper, we study how varying the thickness and particle size of a gravel cushion influences its energy-consumption and buffering effects. We performed a series of laboratory drop tests by dropping blocks from a fixed height onto cushions of different thicknesses and particle sizes. The results indicate that, for a given impact energy, the cushion thickness has a strong influence on the measured coefficient of restitution (COR) and therefore impact pressure. Additional tests were performed to study how the radius of the block and the height it is dropped from affect the measured COR. This showed that as the movement height of the block is increased the COR also increases, and blocks with larger radii exhibit a larger variability in measured COR. Finally, we investigated the influence of rockfall block radius, r, movement height, H, cushion thickness, h, and particle size, d, on the COR and the damage depth, L, of the cushion. The test results reveal that the cushion thickness is the primary design parameter, controlling not only COR, but also the stability of the cushion material. The results provide a theoretical and practical basis for the design of gravel cushions for rockfall protection.

scholarly journals Attainable Region Approach in Analyzing the Breakage Behavior of a Bed of Olivine Sand Particles: Optimizing Impact Energy and Particle Size

Minerals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1096
Author(s):  
Endene Emmanuel ◽  
Vivi Anggraini ◽  
Agusril Syamsir ◽  
Suvash Chandra Paul ◽  
Afshin Asadi
Keyword(s):  
Particle Size ◽  
Impact Energy ◽  
Size Classes ◽  
Drop Weight ◽  
Attainable Region ◽  
Sand Particles ◽  
Particle Size Classes ◽  
Olivine Sand ◽  
The Impact ◽  
Breakage Behavior

In this study, we investigated the breakage behavior of a bed of olivine sand particles using a drop-weight impact test, with drop weights of various shapes (oval, cube, and sphere). An Attainable Region (AR) technique, which is a model-free and equipment-independent technique, was then applied to optimize the impact energy during the breakage process and also to get particles in defined particle size classes. The findings revealed that the different drop weights produce products within the three different particle size classes (feed, intermediate, and fine). A higher mass fraction of materials in the fine-sized class (−75 μm) was obtained when the spherical drop weight was used relative to the cubic and oval drop weights. The drop height was found to have a significant influence on the breakage process. The AR technique proved to be a practical approach for optimizing impact energy and particle size during the breakage of a bed of olivine particles, with potential application in sustainable soil stabilization projects.

Impact Energy for First Crack of Reinforced Concrete with Partial Replacements of Sand by Rubber 1 mm Particle Size

2013 ◽  
Vol 701 ◽  
pp. 261-264 ◽  
Author(s):  
B.H. Abu Bakar ◽  
Mustafa Maher Al-Tayeb ◽  
Hanafi Ismail ◽  
Hazizan M. Akil
Keyword(s):  
Particle Size ◽  
Reinforced Concrete ◽  
Impact Energy ◽  
Crumb Rubber ◽  
Low Velocity Impact ◽  
Moist Air ◽  
Low Velocity ◽  
Velocity Impact ◽  
The Impact ◽  
Waste Crumb Rubber

Effects of partial replacements of sand by waste crumb rubber 1 mm particle size on the performance of reinforced concrete under low velocity impact loading were investigated. Specimens were prepared for 5%, 10% and 20 % replacements by volume of sand. All specimens were cured in moist air for 90 days. For each case, six beams of 100 mm ×100 mm × 500mm were subjected to 5.15 kg hammer from 900mm height. The number of blows of the hammer required to induce the first crack of the beam were recorded. The results are presented in terms of impact energy required for the first crack. The crumb rubbers increased the impact energy for first crack.

scholarly journals Waterfall Algorithm as a tool of investigation the geometrical features of granular porous media

2021 ◽  
Author(s):  
Wojciech Sobieski
Keyword(s):  
Particle Size ◽  
Porous Media ◽  
Lattice Boltzmann ◽  
Granular Media ◽  
Density Ratio ◽  
Geometrical Features ◽  
Granular Porous Media ◽  
Collision Density ◽  
Boltzmann Method ◽  
The Impact

AbstractThe paper describes the so-called Waterfall Algorithm, which may be used to calculate a set of parameters characterising the spatial structure of granular porous media, such as shift ratio, collision density ratio, consolidation ratio, path length and minimum tortuosity. The study is performed for 1800 different two-dimensional random pore structures. In each geometry, 100 individual paths are calculated. The impact of porosity and the particle size on the above-mentioned parameters is investigated. It was stated in the paper, that the minimum tortuosity calculated by the Waterfall Algorithm cannot be used directly as a representative tortuosity of pore channels in the Kozeny or the Carman meaning. However, it may be used indirect by making the assumption that a unambiguous relationship between the representative tortuosity and the minimum tortuosity exists. It was also stated, that the new parameters defined in the present study are sensitive on the porosity and the particle size and may be therefore applied as indicators of the geometry structure of granular media. The Waterfall Algorithm is compared with other methods of determining the tortuosity: A-Star Algorithm, Path Searching Algorithm, Random Walk technique, Path Tracking Method and the methodology of calculating the hydraulic tortuosity based on the Lattice Boltzmann Method. A very short calculation time is the main advantage of the Waterfall Algorithm, what meant, that it may be applied in a very large granular porous media.

scholarly journals Evaluation of Marblewood Dust’s (Marmaroxylon racemosum) Effect on Ignition Risk

2021 ◽  
Vol 11 (15) ◽  
pp. 6874
Author(s):  
Miroslava Vandličkova ◽  
Iveta Markova ◽  
Katarina Holla ◽  
Stanislava Gašpercová
Keyword(s):  
Particle Size ◽  
Dust Particles ◽  
Wood Dust ◽  
Sieve Analysis ◽  
Granulometric Analysis ◽  
Analysis Measurement ◽  
Risk Research ◽  
Minimum Ignition Temperature ◽  
The Impact

The paper deals with the selected characteristics, such as moisture, average bulk density, and fraction size, of tropical marblewood dust (Marmaroxylon racemosum) that influence its ignition risk. Research was focused on sieve analysis, granulometric analysis, measurement of moisture level in the dust, and determination of the minimum ignition temperatures of airborne tropical dust and dust layers. Samples were prepared using a Makita 9556CR 1400W grinder and K36 sandpaper for the purpose of selecting the percentages of the various fractions (<63, 63, 71, 100, 200, 315, 500 μm). The samples were sized on an automatic vibratory sieve machine Retsch AS 200. More than 65% of the particles were determined to be under 100 μm. The focus was on microfractions of tropical wood dust (particles with a diameter of ≤100 µm) and on the impact assessment of particle size (particle size <100 µm) on the minimum ignition temperatures of airborne tropical dust and dust layers. The minimum ignition temperature of airborne marblewood dust decreased with the particle size to the level of 400 °C (particle size 63 μm).

Response and failure modes of biaxial warp-knitted flexible composite subject to low-velocity impact

2021 ◽  
pp. 152808372110154
Author(s):  
Ziyu Zhao ◽  
Tianming Liu ◽  
Pibo Ma
Keyword(s):  
Impact Energy ◽  
Linear Density ◽  
Failure Modes ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Minor Effect ◽  
Low Velocity ◽  
Velocity Impact ◽  
Flexible Composites ◽  
The Impact

In this paper, biaxial warp-knitted fabrics were produced with different high tenacity polyester linear density and inserted yarns density. The low-velocity impact property of flexible composites made of polyurethane as matrix and biaxial warp-knitted fabric as reinforcement has been investigated. The effect of impactor shape and initial impact energy on the impact response of flexible composite is tested. The results show that the initial impact energy have minor effect on the impact response of the biaxial warp-knitted flexible composites. The impact resistance of flexible composite specimen increases with the increase of high tenacity polyester linear density and inserted yarns density. The damage morphology of flexible composite materials is completely different under different impactor shapes. The findings have theoretical and practical significance for the applications of biaxial warp-knitted flexible composite.

Sign in / Sign up

Export Citation Format

Share Document