scholarly journals NUMERICAL STUDY OF THE GASKET THERMAL CONDUCTIVITY EFFECT ON THE THERMAL CONTACT RESISTANCE BETWEEN TWO SOLIDS IN CONTACT

2017 ◽  
Vol 8 ◽  
Author(s):  
Rachid Chadouli ◽  
Frédéric Lebon ◽  
Iulian Rosu ◽  
Mohammed Makhlouf
Keyword(s):  
Thermal Conductivity ◽  
Contact Resistance ◽  
Thermal Contact Resistance ◽  
Numerical Study ◽  
Thermal Contact

High‐Temperature Skin Softening Materials Overcoming the Trade‐Off between Thermal Conductivity and Thermal Contact Resistance

Small ◽  
2021 ◽  
pp. 2102128
Author(s):  
Taehun Kim ◽  
Seongkyun Kim ◽  
Eungchul Kim ◽  
Taesung Kim ◽  
Jungwan Cho ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
High Temperature ◽  
Contact Resistance ◽  
Thermal Contact Resistance ◽  
Thermal Contact ◽  
Trade Off

Through-Plane Thermal Conductivity of PEMFC Porous Transport Layers

2010 ◽  
Vol 8 (2) ◽  
Author(s):  
Odne S. Burheim ◽  
Jon G. Pharoah ◽  
Hannah Lampert ◽  
Preben J. S. Vie ◽  
Signe Kjelstrup
Keyword(s):  
Thermal Conductivity ◽  
Contact Resistance ◽  
Thermal Contact Resistance ◽  
Thermal Contact ◽  
Residual Water ◽  
Order Of Magnitude ◽  
Thermal Conductivities

We report the through-plane thermal conductivities of the several widely used carbon porous transport layers (PTLs) and their thermal contact resistance to an aluminum polarization plate. We report these values both for wet and dry samples and at different compaction pressures. We show that depending on the type of PTL and the existence of residual water, the thermal conductivity of the materials varies from 0.15 W K−1 m−1 to 1.6 W K−1 m−1, one order of magnitude. This behavior is the same for the contact resistance varying from 0.8 m2 K W−1 to 11×10−4 m2 K W−1. For dry PTLs, the thermal conductivity decreases with increasing polytetrafluorethylene (PTFE) content and increases with residual water. These effects are explained by the behavior of air, water, and PTFE in between the PTL fibers. It is also found that Toray papers of differing thickness exhibit different thermal conductivities.

scholarly journals Effects of pressure and temperature on thermal contact resistance between different materials

2015 ◽  
Vol 19 (4) ◽  
pp. 1369-1372 ◽  
Author(s):  
Zhe Zhao ◽  
Hai-Ming Huang ◽  
Qing Wang ◽  
Song Ji
Keyword(s):  
Thermal Conductivity ◽  
Contact Resistance ◽  
Thermal Contact Resistance ◽  
Experimental Approach ◽  
Phenolic Resin ◽  
Thermal Conductivity Coefficient ◽  
Thermal Contact ◽  
Carbon Composites ◽  
Interfacial Temperature ◽  
Temperature And Pressure

To explore whether pressure and temperature can affect thermal contact resistance, we have proposed a new experimental approach for measurement of the thermal contact resistance. Taking the thermal contact resistance between phenolic resin and carbon-carbon composites, cuprum, and aluminum as the examples, the influence of the thermal contact resistance between specimens under pressure is tested by experiment. Two groups of experiments are performed and then an analysis on influencing factors of the thermal contact resistance is presented in this paper. The experimental results reveal that the thermal contact resistance depends not only on the thermal conductivity coefficient of materials, but on the interfacial temperature and pressure. Furthermore, the thermal contact resistance between cuprum and aluminum is more sensitive to pressure and temperature than that between phenolic resin and carbon-carbon composites.

Effective Thermal Conductivity of Composites Reinforced with Curvilinearly Anisotropic Inclusions with Kapitza Contact Resistance

2006 ◽  
Vol 306-308 ◽  
pp. 775-780
Author(s):  
Tung Yang Chen
Keyword(s):  
Thermal Conductivity ◽  
Contact Resistance ◽  
Closed Form ◽  
Effective Thermal Conductivity ◽  
Thermal Contact Resistance ◽  
Thermal Contact ◽  
Transversely Isotropic ◽  
Closed Form Expression ◽  
Form Expression ◽  
Micromechanical Models

Effective thermal conductivities of composites consisting of curvilinearly anisotropic inclusions with Kapitza thermal contact resistance between the constituents are considered. We show that the effect of these curvilinearly anisotropic inclusions can be exactly simulated by certain equivalent isotropic or transversely isotropic inclusions. Three different micromechanical models are employed to estimate the effective thermal conductivity of the composite. Interestingly, all these methods result in the same simple, closed-form expression.

Numerical Study on Substrate Remelting, Flow, and Resolidification in Microcasting

Volume 3 ◽  
2004 ◽  
Author(s):  
F. J. Hong ◽  
H.-H. Qiu
Keyword(s):  
Contact Resistance ◽  
Thermal Contact Resistance ◽  
Numerical Study ◽  
Thermal Contact ◽  
Spreading Factor ◽  
Droplet Spreading ◽  
Molten Droplet ◽  
Front Shape ◽  
Complex Fluid

A large and highly superheated molten droplet impacting onto the substrate during the microcasting was studied numerically. In this study, same material for both the droplet and the substrate was considered. Numerical model including the complex fluid dynamics of droplet, interfacial thermal contact resistance, and substrate remelting, as well as the flow in the substrate has been developed. Numerical simulations of a microcasting experiment were conducted with the different thermal contact resistances. The results of simulations show that the spreading factor and substrate remelting agreed well with the experimental data under the assumption of an appropriate thermal contact resistance. It is also found that the thermal contact resistance plays an important role not only in droplet spreading arrest but also in the determination of substrate remelting volume and remelting front shape. The effects of droplet impacting velocity, superheat and substrate temperature were also investigated.

Thermal Contact Resistance at a Metal Foam-Solid Surface Interface

2011 ◽  
Author(s):  
Ehsan Sadeghi ◽  
Scott Hsieh ◽  
Majid Bahrami
Keyword(s):  
Thermal Conductivity ◽  
Contact Resistance ◽  
Effective Thermal Conductivity ◽  
Contact Area ◽  
Thermal Contact Resistance ◽  
Thermal Contact ◽  
Metal Foams ◽  
Real Contact Area ◽  
The Real ◽  
Real Contact

Accurate information on heat transfer and temperature distribution in metal foams is necessary for design and modeling of thermal-hydraulic systems incorporating metal foams. The analysis of this process requires determination of the effective thermal conductivity as well as the thermal contact resistance (TCR) associated with the interface between the metal foams and adjacent surfaces/layers. In the present study, a test bed that allows the separation of effective thermal conductivity and thermal contact resistance in metal foams is described. Measurements are performed in a vacuum under varying compressive loads using ERG Duocel aluminum foam samples with different porosities and pore densities. Also, a graphical method associated with a computer code is developed to demonstrate the distribution of contact spots and estimate the real contact area at the interface. Our results show that the porosity and the effective thermal conductivity remain unchanged with the variation of compression in the range of 0 to 2 MPa; but TCR decreases significantly with pressure due to an increase in the real contact area at the interface. Moreover, the ratio of real to nominal contact area varies between 0 to 0.013, depending upon the compressive force, porosity, and surface characteristics.

scholarly journals Measurement of the Thermophysical Properties of Anisotropic Insulation Materials with Consideration of the Effect of Thermal Contact Resistance

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1353 ◽  
Author(s):  
Dongxu Han ◽  
Kai Yue ◽  
Liang Cheng ◽  
Xuri Yang ◽  
Xinxin Zhang
Keyword(s):  
Thermal Conductivity ◽  
Thermal Resistance ◽  
Contact Resistance ◽  
Thermal Contact Resistance ◽  
Thermal Contact ◽  
Thermal Contact Conductance ◽  
Maximum Deviation ◽  
Insulation Materials ◽  
Steady State Method ◽  
Different Temperatures

A novel method involving the effect of thermal contact resistance (TCR) was proposed using a plane heat source smaller than the measured samples for improving measurement accuracy of the simultaneous determination of in-plane and cross-plane thermal conductivities and the volumetric heat capacity of anisotropic materials. The heat transfer during the measurement process was mathematically modeled in a 3D Cartesian coordinate system. The temperature distribution inside the sample was analytically derived by applying Laplace transform and the variables separation method. A multiparameter estimation algorithm was developed on the basis of the sensitivity analysis of the parameters to simultaneously estimate the measured parameters. The correctness of the algorithm was verified by performing simulation experiments. The thermophysical parameters of insulating materials were experimentally measured using the proposed method at different temperatures and pressures. Fiber glass and ceramic insulation materials were tested at room temperature. The measured results showed that the relative error was 1.6% less than the standard value and proved the accuracy of the proposed method. The TCRs measured at different pressures were compared with those obtained using the steady-state method, and the maximum deviation was 8.5%. The thermal conductivity obtained with the contact thermal resistance was smaller than that without the thermal resistance. The measurement results for the anisotropic silica aerogels at different temperatures and pressures revealed that the thermal conductivity and thermal contact conductance increased as temperature and pressure increased.

Sign in / Sign up

Export Citation Format

Share Document