Electrochemical Investigation of Under-Deposit Corrosion Behavior for Aluminum Brass in Artificial Seawater

CORROSION ◽  
10.5006/3428 ◽  
2020 ◽  
Vol 76 (11) ◽  
pp. 1050-1063
Author(s):  
Hong Ju ◽  
Weihui Xu ◽  
Jiejing Chen ◽  
Dalei Zhang ◽  
Guomin Liu ◽  
...  
Keyword(s):  
Corrosion Rate ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Electrolytic Cell ◽  
Artificial Seawater ◽  
Localized Corrosion ◽  
Effect Of Temperature ◽  
Multielectrode Arrays ◽  
Energy Dispersive Spectrometry Analysis ◽  
Spectrometry Analysis

The under-deposit corrosion behavior and mechanism of aluminum brass (HAl77-2) were investigated in artificial seawater with a custom double electrolytic cell. The experiments included linear polarization, electrochemical impedance spectroscopy, and multielectrode arrays analysis. The electrochemical results revealed a pronounced effect of temperature on the under-deposit corrosion behavior of HAl77-2. The corrosion of HAl77-2 inside the CaCO3 scale is aggravated with increasing temperature. However, the increasing frequency of the corrosion rate of HAl77-2 gradually decreased after 333 K. Moreover, in the desalination of artificial seawater, the corrosion rate of HAl77-2 in the occulated area initially increased and subsequently decreased with increasing Cl− concentration. The scanning electron microscopy and energy dispersive spectrometry analysis showed a remarkable appearance of selective localized corrosion on the surface of HAl77-2.

scholarly journals Assessment of nickel titanium and beta titanium corrosion resistance behavior in fluoride and chloride environments

2013 ◽  
Vol 83 (5) ◽  
pp. 864-869 ◽  
Author(s):  
Elisa J. Kassab ◽  
José Ponciano Gomes
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Fluoride Concentration ◽  
Nickel Titanium ◽  
Localized Corrosion ◽  
General Corrosion ◽  
Nacl Solution ◽  
Galvanic Coupling ◽  
Beta Titanium

ABSTRACT Objective: To assess the influence of fluoride concentration on the corrosion behavior of nickel titanium (NiTi) superelastic wire and to compare the corrosion resistance of NiTi with that of beta titanium alloy in physiological solution with and without addition of fluoride. Materials and Methods: NiTi corrosion resistance was investigated through electrochemical impedance spectroscopy and anodic polarization in sodium chloride (NaCl 0.15 M) with and without addition of 0.02 M sodium fluoride (NaF), and the results were compared with those associated with beta titanium. The influence of fluoride concentration on NiTi corrosion behavior was assessed in NaCl (0.15 M) with and without 0.02, 0.04, 0.05, 0.07, and 0.12 M NaF solution. Galvanic corrosion between NiTi and beta titanium were investigated. All samples were characterized by scanning electron microscopy. Results: Polarization resistance decreased when NaF concentration was increased, and, depending on NaF concentration, NiTi can suffer localized or generalized corrosion. In NaCl solution with 0.02 M NaF, NiTi suffer localized corrosion, while beta titanium alloys remained passive. Current values near zero were observed by galvanic coupling of NiTi and beta titanium. Conclusions: There is a decrease in NiTi corrosion resistance in the presence of fluoride. The corrosion behavior of NiTi alloy depends on fluoride concentration. When 0.02 and 0.04 M of NaF were added to the NaCl solution, NiTi presented localized corrosion. When NaF concentration increased to 0.05, 0.07, and 0.12 M, the alloy presented general corrosion. NiTi corrosion resistance behavior is lower than that of beta titanium. Galvanic coupling of these alloys does not increase corrosion rates.

Corrosion behavior of a new 25Cr-3Ni-7Mn-0.66 N duplex stainless steel in artificial seawater

2021 ◽  
Vol 63 (6) ◽  
pp. 505-511
Author(s):  
Songkran Vongsilathai ◽  
Anchaleeporn Waritswat Lothongkum ◽  
Gobboon Lothongkum
Keyword(s):  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Passive Film ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Melting Furnace ◽  
Artificial Seawater ◽  
Vacuum Arc ◽  
Significant Difference ◽  
Type Semiconductor

Abstract A new duplex 25Cr-3Ni-7Mn-0.66 N alloy was prepared in a vacuum arc re-melting furnace and characterized by metallographic and EPMA methods. Its corrosion behavior was investigated by potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and a Mott-Schottky (M-S) analysis in artificial seawater at room temperature and compared with those of super and normal commercial duplex stainless steel (SDSS and DSS). No significant difference in the open circuit potentials and pitting potentials was observed. Its passive film current density lies between those of SDSS and DSS. This was confirmed by EIS analysis. A pit attack was observed on the δ-phase for all duplex samples, because the PREN16 of the δ-phase was lower than that of the γ-phase. From the Mott-Schottky analysis, the passive films were found to be composed of bi-layer structures, a p-type semiconductor inner layer, and a n-type semiconductor outer layer. The degree of defect as well as the effect of nitrogen in passive film layer are discussed with respect to the point defect model.

Corrosion Protection of Nano-Silica Powder Coatingon Artificial Seawater

2021 ◽  
Vol 904 ◽  
pp. 519-524
Author(s):  
Gui Yun Zhang ◽  
Yong Wang ◽  
Tian Wei Zhang ◽  
Chen Yu Zhao
Keyword(s):  
Corrosion Protection ◽  
Corrosion Behavior ◽  
Sea Water ◽  
Electrochemical Impedance ◽  
Water Solution ◽  
Electrochemical Corrosion ◽  
Artificial Seawater ◽  
Protection Effect ◽  
Aluminum Sheets ◽  
Electrochemical Corrosion Behavior

Sea water resources are extensive and can be used to extinguish fires, but their corrosiveness is a major problem. Using the method of electrochemical workstation, the electrochemical corrosion behavior of aluminum sheet in artificial sea water solution and silica-coated artificial seawater was studied; by analyzing the surface morphology, polarization curve and electrochemical impedance spectroscopy, the electrochemical corrosion behavior of aluminum sheets under different immersion times and different immersion media is obtained. The conclusion is that the coating of nanosilica powder has a certain corrosion protection effect on artificial seawater.

scholarly journals Effect of Temperature on the Corrosion Behavior of Biodegradable AZ31B Magnesium Alloy in Ringer’s Physiological Solution

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 591 ◽  
Author(s):  
Sebastian Feliu ◽  
Lucien Veleva ◽  
Federico García-Galvan
Keyword(s):  
Corrosion Rate ◽  
Electrochemical Impedance ◽  
Physiological Solution ◽  
Corrosion Layer ◽  
Effect Of Temperature ◽  
X Ray ◽  
Ringer’S Solution ◽  
Corrosion Behaviors ◽  
Az31b Alloy ◽  
Increasing Temperature

In this work, the corrosion behaviors of the AZ31B alloy in Ringer’s solution at 20 °C and 37 °C were compared over four days to better understand the influence of temperature and immersion time on corrosion rate. The corrosion products on the surfaces of the AZ31B alloys were examined by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). Electrochemical impedance spectroscopy (EIS) provided information about the protective properties of the corrosion layers. A significant acceleration in corrosion rate with increasing temperature was measured using mass loss and evolved hydrogen methods. This temperature effect was directly related to the changes in chemical composition and thickness of the Al-rich corrosion layer formed on the surface of the AZ31B alloy. At 20 °C, the presence of a thick (micrometer scale) Al-rich corrosion layer on the surface reduced the corrosion rate in Ringer’s solution over time. At 37 °C, the incorporation of additional Mg and Al compounds containing Cl into the Al-rich corrosion layer was observed in the early stages of exposure to Ringer’s solution. At 37 °C, a significant decrease in the thickness of this corrosion layer was noted after four days.

Influence of Tempertature on Corrosion Behavior of DH36 Steel in Seawater Full Immersion Zone

2015 ◽  
Vol 1120-1121 ◽  
pp. 1115-1118
Author(s):  
Peng Cheng ◽  
Xian Qiu Huang
Keyword(s):  
Regression Analysis ◽  
Linear Regression ◽  
Corrosion Rate ◽  
Corrosion Behavior ◽  
Linear Regression Analysis ◽  
Artificial Seawater ◽  
Corrosion Behaviors ◽  
Corrosion Problem ◽  
Full Immersion ◽  
The Relationship

Aimed at the corrosion problem of DH36 steel in the seawater full immersion zone, corrosion environment of full immersion zone has been simulated with artificial seawater in laboratory. The corrosion behaviors of DH36 steel in the full immersion zone were investigated by using full immersion tests. The morphology of corrosion products was observed by SEM. Using linear regression analysis to establish the relationship between temperature and the corrosion of DH36 steel. The results showed that the corrosion of DH36 steel immersed in full immersion zone corroded seriously, and the corrosion rate of DH36 steel increased with temperature increasing.

Influence of electrosynthesis conditions and Al2O3 nanoparticles on corrosion protection effect of polypyrrole films

2014 ◽  
Vol 61 (3) ◽  
pp. 146-152 ◽  
Author(s):  
Ali Ehsani ◽  
Mohammad Ghasem Mahjani ◽  
Maryam Nasseri ◽  
Majid Jafarian
Keyword(s):  
Oxygen Reduction ◽  
Corrosion Protection ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Reduction Process ◽  
Artificial Seawater ◽  
Alumina Nanoparticles ◽  
Al2o3 Nanoparticles ◽  
Active Dissolution ◽  
Content Type

Purpose – The purpose of this paper was to investigate the anti-corrosion behavior of polypyrrole (PPy) films in different states and presence of alumina nanoparticles synthesized by galvanostatic electropolymerization on stainless steel (SS) electrodes in an artificial seawater solution using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). Design/methodology/approach – The electrochemical measurements were used to examine the effects of PPy and its nanocomposite on the corrosion behavior of SS type 316L in artificial seawater. A standard electrochemical cell with three electrodes was used for the measurements. The electrochemical response of the coated electrodes in the doped and the undoped state was compared with that of a bare electrode. Corrosion rate information was obtained by the Tafel extrapolation method, where the intersection point of a cathodic and an anodic polarization curve provides both the corrosion potential and the corrosion current. EIS measurements confirmed the potentiodynamic and open circuit potential (OCP) results. The microstructure of the obtained films was investigated by scanning electron microscopy. Findings – The results showed that the coated polymer films shifted the electrode potential toward more positive potentials, but this shift did not lead to passivation. However, a notable synergy was observed between PPy undoped film, oxygen reduction and iron dissolution. The potential of the SS remained in the active dissolution region, and it was not possible to produce a passive oxide layer in this region. PPy separates the metal dissolution process from the oxygen reduction process. This would prevent the local pH increase at the metal surface and subsequent delamination. The polarization curves, EOCP and impedance measurements showed that PPy undoped/Al2O3 layers show promise as good candidates for the corrosion protection of reactive metals. Originality/value – This paper presents that electrodes coated with undoped PPy synthesized in the presence of dodecyl sulfate anions and Al2O3 nanoparticles offered a noticeable enhancement of protection against corrosion processes.

scholarly journals Corrosion Behavior of 3% Cr Casing Steel in CO2-Containing Environment: A Case Study

2018 ◽  
Vol 11 (1) ◽  
pp. 1-13 ◽  
Author(s):  
Lin Xu ◽  
Jie Xu ◽  
Ming-biao Xu ◽  
Si-yang Li ◽  
Shuai Liu ◽  
...  
Keyword(s):  
Corrosion Rate ◽  
Corrosion Product ◽  
Corrosion Behavior ◽  
Exposure Time ◽  
Corrosion Products ◽  
Localized Corrosion ◽  
Internal Corrosion ◽  
Tafel Polarization ◽  
Water Cut ◽  
Increasing Temperature

Introduction: The production casing of 3% Cr steel has encountered severe internal corrosion in Huizhou Oilfield. To disclose corrosion behavior of inner casing, a series of corrosion exposure tests were systematically conducted on 3% Cr coupons in terms of in-field conditions. Material and Methods: Influence of exposure time, temperature, and water-cut on the CO2 corrosion of 3% Cr steel was investigated, and analyses on weight loss, composition and morphology of corrosion product, and Tafel polarization curves were further carried out. Result: The results showed that the corrosion rate of 3% Cr steel increased with increasing temperature, but such trend descended when the temperature exceeded 65°C due to formation of an compact and adherent corrosion product film on the surface of 3% Cr coupons. While varying exposure time from 7 days to 14 days, the corrosion rate decreased, and the Cr and O enrichment was determined in the corrosion products. The corrosion rate of 3% Cr steel increased with a continuous increment of water-cuts, especially when the water-cut was larger than 40%. Conclusion: The localized corrosion can happen at the lower water-cut due to the presence of amorphous films. The main corrosion products were FeCO3, Cr5O12, Fe2O3, and Fe-Cr. Entry of CO2 to the simulated formation water caused an increase in the anodic Tafel slope, and accelerated dissolution of 3% Cr steel.

Effects of Different Ions on the Corrosion Behavior of SM 80SS Tubing Steel in CO2/H2S Containing Aqueous Solution

2013 ◽  
Vol 734-737 ◽  
pp. 1367-1373
Author(s):  
Guan Fa Lin ◽  
Xun Chang Dong ◽  
Shi Dong Zhu ◽  
Zhen Quan Bai
Keyword(s):  
Aqueous Solution ◽  
Weight Loss ◽  
Corrosion Rate ◽  
Corrosion Behavior ◽  
Polarization Resistance ◽  
Electrochemical Impedance ◽  
Electrochemical Reaction ◽  
Initial Period ◽  
Activation Reaction ◽  
Linear Polarization Resistance

As an attempt to contribute to the understanding of the corrosion processes of anti-sulfur steel in CO2and H2S containing environment with different species, the corrosion behavior of SM 80SS tubing steel immersed in CO2and H2S containing solution was analyzed in this work. To determine the corrosion behavior of SM80SS steel, the linear polarization resistance (LPR) and electrochemical impedance spectroscopy (EIS) techniques were used, as well as weight loss test and surface analysis. The results showed that the presence of Cl-quickened the anodic dissolution processes and rapidly increased the corrosion rate of SM 80SS steel, and that the addition of Ca2+and Mg2+reduced corrosion rate. The corrosion processes of SM 80SS steel were controlled by the electrochemical reaction in the initial period and then converted to be controlled by electrochemical and activation reaction with increasing Cl-. Keywords: SM 80SS tubing steel; CO2/H2S corrosion; EIS; Chloride; Ca2++ Mg2+

Corrosion Behavior of Al-Sn-Bi Alloys in Ethylene Glycol-Water Mixtures

CORROSION ◽  
2012 ◽  
Vol 68 (5) ◽  
pp. 421-431
Author(s):  
J.L. Gama-Ferrer ◽  
J.G. Gonzalez-Rodriguez ◽  
I. Rosales ◽  
J. Uruchurtu
Keyword(s):  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Corrosion Rate ◽  
Ethylene Glycol ◽  
Corrosion Behavior ◽  
Potentiodynamic Polarization ◽  
Electrochemical Noise ◽  
Electrochemical Impedance ◽  
Electrochemical Techniques ◽  
Potentiodynamic Polarization Curves

A study of the effect of Sn (1, 2, 3.5, 4.5, and 5 wt%) and Bi (0.5, 1.5, 3, and 4%) on the corrosion behavior of Al in ethylene glycol (C2H6O2)-40% water mixtures at 20, 40, and 60°C has been carried out using electrochemical techniques. Techniques include potentiodynamic polarization curves, electrochemical impedance spectroscopy (EIS), and electrochemical noise (EN) measurements. The three techniques have shown that additions of either Sn or Bi contents increased the corrosion rate of pure Al in all cases, and that generally speaking, the corrosion rate increased by increasing the temperature except for the alloy containing 1% Sn + 4% Bi, which showed the lowest corrosion rate at 60°C. This was because of a galvanic effect from the presence of Sn and/or Bi particles on the surface alloy, which acted as local cathodes, leading to an acceleration of corrosion. Nyquist diagrams showed two semicircles at 20°C and only one at 40°C or 60°C for all the alloys, showing two different corrosion-controlling mechanisms. EN measurements showed evidence of a mixture of both localized and uniform types of corrosion for all Al-based alloys.

scholarly journals Electrochemical Investigation of Corrosion of X80 Steel under Elastic and Plastic Tensile Stress in CO2 Environment

Metals ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 949 ◽  
Author(s):  
Wei Wu ◽  
Hailong Yin ◽  
Hao Zhang ◽  
Jia Kang ◽  
Yun Li ◽  
...  
Keyword(s):  
Corrosion Rate ◽  
Tensile Stress ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Pipeline Steel ◽  
Open Circuit ◽  
Co2 Corrosion ◽  
X80 Pipeline Steel ◽  
X80 Steel ◽  
Co2 Environment

An investigation into the electrochemical corrosion behavior of X80 pipeline steel under different elastic and plastic tensile stress in a CO2-saturated NaCl solution has been carried out by using open-circuit potential, potentiodynamic polarization, electrochemical impedance spectroscopy, and surface analysis techniques. The results show that the corrosion rate of X80 steel first increases and then slightly decreases with the increase of elastic tensile stress, whereas the corrosion rate sharply increases with the increase of plastic tensile stress. Both elastic and plastic tensile stress can enhance steel corrosion by improving the electrochemical activity of both anodic and cathodic reactions. Moreover, compared with elastic tensile stress, plastic tensile stress has a more significant effect. Furthermore, electrochemical reactions for CO2 corrosion and mechanoelectrochemical effect are used to reasonably explain the corrosion behavior of stressed X80 steel in CO2 environment.

Sign in / Sign up

Export Citation Format

Share Document