Removal of copper and cadmium from simulated wastewater using coupled internal electrolysis with flocculation: a comparison of effects and investigation of mechanisms

2020 ◽  
Vol 189 ◽  
pp. 329-337 ◽  
Author(s):  
Luting Pan ◽  
Runqiu Tu ◽  
Ajun Wan ◽  
Yunpeng Wu ◽  
Xinjue Xie
Keyword(s):  
Internal Electrolysis ◽  
Simulated Wastewater

SEQUESTRATION OF COPPER (II) FROM SIMULATED WASTEWATER USING PRE-TREATED RICE HUSK WASTE BIOMASS

2016 ◽  
Vol 15 (8) ◽  
pp. 1689-1703 ◽  
Author(s):  
Ackmez Mudhoo ◽  
Manjeet Bansal ◽  
Vinod Kumar Garg ◽  
Diwan Singh
Keyword(s):  
Rice Husk ◽  
Waste Biomass ◽  
Simulated Wastewater

PHYTOTOXICITY OF WASTEWATER CONTAINING CADMIUM (Cd) USING OLEANDER

2020 ◽  
Vol 51 (4) ◽  
pp. 1231-1238
Author(s):  
Zeki & Ridha
Keyword(s):  
Translocation Factor ◽  
Preliminary Test ◽  
Dry Weight ◽  
Exposure Dose ◽  
Test Duration ◽  
Plant Analysis ◽  
Wet Weight ◽  
Simulated Wastewater ◽  
Almost All ◽  
Plant Shoots

This study was aimed to investigate the ability of N.oleander to remove Cadmium (Cd) from wastewater. A prolonged toxicity test was performed in a single exposure and run for 65 days with various concentrations of Cd. Plants were grown in sand medium and irrigated with simulated wastewater contaminated with Cd, using different concentrations (0, 10, 25, 50, 75 mg/L), which were chosen based on previous preliminary test. The results of physical observation of the plants didn’t show any withering symptoms. The Cd concentration in plants increased, while in water decreased. The results of plant analysis showed that Cd concentration in plant shoots (stems and leaves) was higher than that in roots for almost all exposure doses along the test duration. The concentration of Cd in water decreased significantly from the first week of the test and become (0 mg/l) on day-35 for 10 and 25 mg/l exposure doses, while exceeded the permissible limits for 50 and 75 mg/l exposure doses and were 0.14 and 0.91 mg/l, respectively. Wet weight and dry weight of Oleander decreased with increasing Cd concentration level except for 10 mg/l exposure dose where the plant wet weight and dry weight increased at the end of the test. Bioaccumulation factor (BAF) and Translocation Factor (TF) was found to be greater than 1, indicating that Oleander is a successful hyperaccumulator for Cd.

Factorial Design Optimisation of Solid Phase Extraction for Preconcentration of Parabens in Wastewater Using Ultra-High Performance Liquid Chromatography Triple Quadrupole Mass Spectrometry

2020 ◽  
Vol 16 (4) ◽  
pp. 436-446
Author(s):  
Vallerie A. Muckoya ◽  
Philiswa N. Nomngongo ◽  
Jane C. Ngila
Keyword(s):  
Solid Phase Extraction ◽  
Formic Acid ◽  
Factorial Design ◽  
Solid Phase ◽  
Treatment Plant ◽  
Phase Extraction ◽  
Limit Of Quantification ◽  
Analytical Technique ◽  
Relative Standard ◽  
Simulated Wastewater

Background: Parabens are synthetic esters used extensively as preservatives and/or bactericides in personal care personal products. Objective: Development and validation of a novel robust chemometric assisted analytical technique with superior analytical performances for the determination of ethylparaben, methylparaben and propylparaben, using simulated wastewater matrix. Methods: An automated Solid Phase Extraction (SPE) method coupled with liquid chromatographymass spectrometry was applied in this study. A gradient elution programme comprising of 0.1% formic acid in deionised water (A) and 0.1% formic acid in Methanol (B) was employed on a 100 x 2.1 mm, 3.0 μm a particle size biphenyl column. Two-level (2k) full factorial design coupled with response surface methodology was used for optimisation and investigation of SPE experimental variables that had the most significant outcome of the analytical response. Results: According to the analysis of variance (ANOVA), sample pH and eluent volume were statistically the most significant parameters. The method developed was validated for accuracy, precision, Limits of Detection (LOD) and Limit of Quantification (LOQ) and linearity. The LOD and LOQ established under those optimised conditions varied between 0.04-0.12 μgL−1 and 0.14-0.40 μgL−1 respectively. The use of matrix-matched external calibration provided extraction recoveries between 78-128% with relative standard deviations at 2-11% for two spike levels (10 and 100 μgL-1) in three different water matrices (simulated wastewater, influent and effluent water). Conclusion: The newly developed method was applied successfully to the analyses of parabens in wastewater samples at different sampling points of a wastewater treatment plant, revealing concentrations of up to 3 μgL−1.

scholarly journals Removal of Phenol from Aqueous Solution Using Internal Microelectrolysis with Fe-Cu: Optimization and Application on Real Coking Wastewater

Processes ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 720
Author(s):  
Do Tra Huong ◽  
Nguyen Van Tu ◽  
Duong Thi Tu Anh ◽  
Nguyen Anh Tien ◽  
Tran Thi Kim Ngan ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Ph Value ◽  
Reaction Rate Constant ◽  
Phenol Concentration ◽  
Treated Wastewater ◽  
Coking Wastewater ◽  
X Ray ◽  
Chemical Plating ◽  
Internal Electrolysis ◽  
Phenol Decomposition

Fe-Cu materials were synthesized using the chemical plating method from Fe powder and CuSO4 5% solution and then characterized for surface morphology, composition and structure by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD), respectively. The as-synthesized Fe-Cu material was used for removal of phenol from aqueous solution by internal microelectrolysis. The internal electrolysis-induced phenol decomposition was then studied with respect to various parameters such as pH, time, Fe-Cu material weight, phenol concentration and shaking speed. The optimal phenol decomposition (92.7%) was achieved under the conditions of (1) a pH value of phenol solution of 3, (2) 12 h of shaking at the speed of 200 rpm, (3) Fe-Cu material weight of 10 g/L, (4) initial phenol concentration of 100.98 mg/L and (5) at room temperature (25 ± 0.5 °C). The degradation of phenol using Fe-Cu materials obeyed the second-order apparent kinetics equation with a reaction rate constant of k of 0.009 h−1L mg−1. The optimal process was then tested against real coking wastewater samples, resulting in treated wastewater with favorable water indicators. Current findings justify the use of Fe-Cu materials in practical internal electrolysis processes.

scholarly journals Simultaneous Disinfection and Organic Microcontaminant Removal by UVC-LED-Driven Advanced Oxidation Processes

Water ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1507
Author(s):  
Sara Miralles-Cuevas ◽  
Irene De la Obra ◽  
Elizabeth Gualda-Alonso ◽  
Paula Soriano-Molina ◽  
José L. Casas López ◽  
...  
Keyword(s):  
Advanced Oxidation Processes ◽  
Advanced Oxidation ◽  
Scaling Up ◽  
Bactericidal Effect ◽  
Secondary Effluent ◽  
Bacterial Inactivation ◽  
Bacterial Regrowth ◽  
Oxidation Processes ◽  
Bacteria Inactivation ◽  
Simulated Wastewater

This work presents the comparison of four advanced oxidation processes driven by UVC-LED radiation (278 nm—2 W/m2) for simultaneous bacteria inactivation (Escherichia coli—106 CFU/mL) and microcontaminant removal (imidacloprid—50 µg/L) in simulated wastewater secondary effluent. To this end, the activation of H2O2 and S2O82− as precursors of HO• and SO4•−, respectively, by UVC-LED and UVC-LED/Fe3+–NTA (ferric nitrilotriacetate at 0.1 mM) has been studied at different oxidant concentrations. For the purpose of comparison, conventional chlorination was used as the baseline along with bacterial regrowth 24 h after treatment. Disinfection was achieved within the first 30 min in all of the processes, mainly due to the bactericidal effect of UVC-LED radiation. UVC-LED/H2O2 did not substantially affect imidacloprid removal due to the low HO• generation by UVC irradiation at 278 nm, while more than 80% imidacloprid removal was achieved by the UVC-LED/S2O82−, UVC-LED/Fe3+–NTA/S2O82−, and UVC-LED/Fe3+–NTA/H2O2 processes. The most efficient concentration of both oxidants for the simultaneous disinfection and microcontaminant removal was 1.47 mM. Chlorination was the most effective treatment for bacterial inactivation without imidacloprid removal. These findings are relevant for scaling up UVC-LED photoreactors for tertiary wastewater treatment aimed at removing bacteria and microcontaminants.

scholarly journals Durability Study on High-Performance Fiber-Reinforced Mortar under Simulated Wastewater Pipeline Environment

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3781
Author(s):  
Tianyu Wang ◽  
Yahong Zhao ◽  
Baosong Ma ◽  
Cong Zeng
Keyword(s):  
Mass Loss ◽  
Pore Volume ◽  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Economic Losses ◽  
Structural Deterioration ◽  
Simulated Wastewater ◽  
Corrosive Environments

The acid–alkaline-inducd corrosive environments inside wastewater concrete pipelines cause concrete structural deterioration and substantial economic losses all over the world. High-performance concrete/mortar (HPC) was designed to have better resistance to corrosive environments, with enhanced service life. However, the durability of HPC in wastewater pipeline environments has rarely been studied. A high-performance mortar mixture (M) reinforced by supplemental materials (including fly ash and silica fume) and polyvinyl alcohol (PVA) fibers, together with a mortar mixture (P) consisting of cement, sand and water with similar mechanical performance, were both designed and exposed to simulated wastewater pipeline environments. The visual appearance, dimensional variation, mass loss, mechanical properties, permeable pore volume, and microstructure of the specimens were measured during the corrosion cycles. More severe deterioration was observed when the alkaline environment was introduced into the corrosion cycles. Test results showed that the M specimens had less permeable pore volume, better dimensional stability, and denser microstructure than the P specimens under acid–alkaline-induced corrosive environments. The mass-loss rates of the M specimens were 66.1–77.2% of the P specimens after 12 corrosion cycles. The compressive strength of the M specimens was 25.5–37.3% higher than the P specimens after 12 cycles under corrosive environments. Hence, the high-performance mortar examined in this study was considered superior to traditional cementitious materials for wastewater pipeline construction and rehabilitation.

scholarly journals Visible Light Catalytic Degradation of Aniline Wastewater over Multishaped BiOBr Microcrystals

2015 ◽  
Vol 2015 ◽  
pp. 1-5 ◽  
Author(s):  
Jun Zhang ◽  
Huabo Li ◽  
Hairui Yao ◽  
Hao Zhang
Keyword(s):  
Ionic Liquid ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Hydrothermal Route ◽  
Degradation Ratio ◽  
Soft Templating ◽  
Different Shapes ◽  
Simulated Wastewater ◽  
Surface Microstructures ◽  
Templating Effect

The photooxidation process of aniline-containing simulated wastewater under visible light irradiation over BiOBr microcrystal grains with different shapes was studied. The distinctive surface microstructures of the BiOBr microcrystals, like clustered flower petals and quadrate lamellas, were produced by using imidazole ionic liquid and inorganic bromide as Br sources and by solvothermal and hydrothermal route, respectively. The ionic liquid not only can impact the products’ morphology, but also can largely improve the photocatalytic activity of the BiOBr microcrystals due to the soft templating effect. The top degradation ratio of the aniline wastewater photocatalyzed by lamellar BiOBr crystals is 23.71%, but the equivalent value photocatalyzed by flower petal-like BiOBr crystals is almost twice as much; that is, it reaches 46.51%. The photodegradation effect and mechanism over differently shaped BiOBr microcrystals have been compared.

Sign in / Sign up

Export Citation Format

Share Document