scholarly journals TENSILE TEST ANALYSIS OF NATURAL FIBER REINFORCED COMPOSITE

2014 ◽  
pp. 148-152
Author(s):  
G. VELMURUGAN ◽  
D. VADIVEL ◽  
R. ARRAVIND ◽  
A. MATHIAZHAGAN ◽  
S.P. VENGATESAN
Keyword(s):  
Natural Fiber ◽  
Volume Fraction ◽  
Fiber Composite ◽  
Tensile Load ◽  
Experimental Result ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Test Analysis ◽  
Reinforced Composite ◽  
Strain Stress

This project mainly deals with analysis of tensile properties of Palmyra fiber Reinforced Epoxy Composite that is suitable for automobile application. First, the property of material was obtained on the basis of some assumptions (i.e., Rule of Mixture) and was modeled with reference to ASTM D638. Here the simulation was carried out on specimen under different fiber volume fraction and fiber length. The present work includes the Analysis of Palmyra Fiber Reinforced Epoxy Composites using FEA with various fiber volume fractions and these results were validated with the experimental result. The tensile property of Palmyra fiber composite material can be obtained by using tensometer.During the tensile load, the maximum strain, stress and displacement were obtained and, then this experimental result was compared with the analytical results and the error percentage of these results were calculated.

scholarly journals Mechanical Properties of Banana Fabric and Kenaf Fiber Reinforced Epoxy Composites: Effect of Treatment and Hybridization

2019 ◽  
Vol 8 (10) ◽  
pp. 1870-1874
Keyword(s):  
Mechanical Properties ◽  
Natural Fiber ◽  
Fiber Composite ◽  
Fiber Reinforced Composites ◽  
Synthetic Fiber ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Kenaf Fiber ◽  
Fiber Reinforced Composite ◽  
Reinforced Composite

Nowadays, Natural Fiber Reinforced composites (NFCs) are emerging to be a good substitute for synthetic fiber reinforced composites as NFCs have many advantages such as low density, high specific strength, recyclability, low cost and good sound abatement quality etc. Among all types of NFCs, a vast study has been done on banana fiber and kenaf fiber reinforced composite. However, only limited work has been done on the banana fabric, kenaf fiber reinforced composite and the effect of their hybridization on mechanical properties. In this paper, an attempt has been made to study the mechanical properties of the banana fabric, kenaf fiber and hybrid banana fabric/kenaf fiber reinforced composites. Effect of alkali treatment on kenaf fiber reinforced composite is discussed in the paper. For the present work, plain-woven banana fabric and randomly oriented kenaf fiber are used as reinforcement while the epoxy resin is used as a matrix. samples are fabricated using hand lay-up and vacuum bagging method. Curing is done at ambient temperature (250C-300C) for 48h. Tensile, impact and hardness test has been performed on a specimen according to ASTM standards. Improvement in mechanical properties is observed after alkali (6% NaOH) treatment on kenaf fiber reinforced composite. Tensile testing behavior of randomly oriented kenaf fiber composite has been studied using Finite element method and results are compared with experimental investigations. This topic present big potential because it seeks to find solution for sustainable development with environmental concerns.

scholarly journals Design, Analysis and Manufacturing Polymer Fiber Reinforced Composite Helical Spring

2020 ◽  
Vol 23 (4) ◽  
pp. 338-344
Author(s):  
Hadeer Abdul Rasol Hamed ◽  
Mahmud Rasheed Ismail ◽  
Abdul Rahman Najam
Keyword(s):  
Volume Fraction ◽  
Fuel Efficiency ◽  
Fiber Reinforced Polymer ◽  
Light Weight ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Steel Spring ◽  
Reinforced Composite ◽  
Reinforced Polymer ◽  
Compression Spring

In this work it had been focused on the possibility of replacement of steel spring in suspension system by fiber reinforced polymer composite that is responsible for light weight of spring which leads to reduces the weight of vehicle and improve fuel efficiency. This type of spring used in motor cycles, light weight vehicle.  The design will be simulated by ANSYS workbench. Then, E-Glass fiber has been used to fabricate helical compression spring of 40%   fiber volume fraction of glass. with polyester resin. The deflection of glass reinforced composite spring is more than steel spring but within permissible limit. weight of composite spring is reduced by 57% than of steel.

Effects of Fiber Contents on Wear Resistance of Salacca zalacca Frond Fiber Reinforced Phenolic

2019 ◽  
Vol 948 ◽  
pp. 181-185
Author(s):  
Heru Santoso Budi Rochardjo ◽  
Muhammad Ridlo
Keyword(s):  
Fiber Volume Fraction ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Agricultural Waste ◽  
Natural Fibers ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Environment Friendly ◽  
Specific Strength ◽  
Main Factor

In the last decades, natural fiber composites have received much attention as important structural materials for lightweight components in automotive, and space industries because of low density, high specific strength, and environment-friendly materials. Some natural fibers, however, still not applied in more useful structure, one of which is the frond fiber of snake fruit (salacca zalacca). This fiber is usually just burned or fired as the agricultural waste. The present paper presents the result of the development of frond salacca fiber as the wear component of natural fiber reinforced phenolic. In this composite, the fiber and the phenolic are in the form of powder. The variation of fiber volume fraction was used as the main factor in the tribology characteristics of the composite. The specific wear and also the hardness is then compared to that of the existed commercially available motorbike brake pad as a comparison.

Short Fiber Reinforced Composite: The Effect of Fiber Length and Volume Fraction

2006 ◽  
Vol 7 (5) ◽  
pp. 10-17 ◽  
Author(s):  
Lippo V.J. Lassila ◽  
Pekka K. Vallittu ◽  
Sufyan K. Garoushi
Keyword(s):  
Mechanical Properties ◽  
Fiber Length ◽  
Volume Fraction ◽  
Testing Machine ◽  
Short Fiber ◽  
Bending Test ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Fiber Reinforced Composite ◽  
Reinforced Composite

Abstract Aim The aim of this study was to determine the effect of short fiber volume fraction and fiber length on some mechanical properties of short fiber-reinforced composite (FRC). Methods and Materials Test specimens (2 x 2 x 25 mm3) and (9.5 x 5.5 x 3 mm3) were made from short random FRC and prepared with different fiber volumes (0%-22%) and fiber lengths (1-6 mm). Control specimens did not contain fiber reinforcement. The test specimens (n=6) were either dry stored or thermocycled in water (x10.000, 5 – 55°C) before loading (three-point bending test) according to ISO 10477 or statically loaded with a steel ball (Ø 3.0 mm) with a speed of 1.0 mm/min until fracture. A universal testing machine was used to determine the flexural properties and the load-bearing capacity. Data were analyzed using analysis of variance (ANOVA) (p=0.05) and a linear regression model. Results The highest flexural strength and fracture load values were registered for specimens with 22 vol% of fibers (330 MPa and 2308 N) and with 5 mm fiber length (281 MPa and 2222 N) in dry conditions. Mechanical properties of all test specimens decreased after thermocycling. ANOVA analysis revealed all factors were affected significantly on the mechanical properties (p<0.001). Conclusions By increasing the volume fraction and length of short fibers up to 5 mm, which was the optimum length, the mechanical properties of short FRC were improved. Citation Garoushi SK, Lassila LVJ, Vallittu PK. Short Fiber Reinforced Composite: The Effect of Fiber Length and Volume Fraction. J Contemp Dent Pract 2006 November;(7)5:010-017.

Compression molding of algae fiber and epoxy composites: Modeling of elastic modulus

2016 ◽  
Vol 37 (19) ◽  
pp. 1202-1216 ◽  
Author(s):  
Alejandra Constante ◽  
Selvum Pillay
Keyword(s):  
Fiber Volume Fraction ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Fiber Composite ◽  
Compaction Pressure ◽  
The United States ◽  
Fiber Composites ◽  
Epoxy Composites ◽  
Natural Fiber Composites ◽  
Fiber Volume

The demand for natural fiber composites in the automotive industry in both Europe and the United States has been forecasted to increase in the coming years. The natural fiber composites based on highly commercialized fibers such as flax, hemp, and sisal has grown to become an important sector of polymeric composites. However, little attention has been addressed to expanding natural fiber composites to include new sources of emerging natural reinforcements, such as reclaimed algae fibers, that have a multiple environmental benefits. Not only are extracted algae fibers biodegradable, the reclamation process has the added benefit of restoring health of waterways choked with algae. This study focuses on the processability of algae fiber–epoxy composites. Short fibers, chemically extracted from raw reclaimed algae, were prepared for natural fiber composite products in two ways. First, randomly oriented mats were produced using the wet-laid process to create layered, compression-molded laminates. Second, loose fibers were dispersed directly into the thermoset matrix to produce a bulk molding compound that was further compression molded into composite lamina. The effect of processing variables such as compaction pressure, temperature, and time were addressed. Moreover, the effect of fiber volume fraction ( υf) and fiber form were considered. Enhanced mechanical properties were found when 56% υf algae fiber was used for the compression-molded laminates composite. This variant exhibited an improvement on the flexural and tensile modulus of 70% and 86% when compared to the neat epoxy. However, the volume of porosity on the same variant was 11% due to lack of compression in some of the fibers. The effect of porosity on the theoretical stiffness was estimated by using the Cox–Krenchel model. Furthermore, an empirical exponential model was formulated to characterize the multi-scale effect of compaction pressure on the overall fiber volume fraction, υf.

Predicting tensile behaviors of short flax fiber-reinforced polymer–matrix composites using a modified shear-lag model

2018 ◽  
Vol 52 (27) ◽  
pp. 3701-3713 ◽  
Author(s):  
Xiaoshuang Xiong ◽  
Shirley Z Shen ◽  
Lin Hua ◽  
Xiang Li ◽  
Xiaojin Wan ◽  
...  
Keyword(s):  
Natural Fiber ◽  
Volume Fraction ◽  
Shear Stiffness ◽  
Interfacial Shear ◽  
Fiber Reinforced ◽  
Shear Lag ◽  
Fiber Volume ◽  
Shear Lag Model ◽  
Lag Model ◽  
Fiber Matrix

Natural fiber-reinforced composites are increasingly being used in the industry. The fiber–matrix interfacial properties of the composites are influenced by many factors, including chemical treatment of the natural fiber, type of polymer matrix, composites fabrication method, and process and the service environment of the composites. In this paper, a modified shear-lag model based on a cohesive fiber/matrix interface is proposed and applied to the analysis of the stress–transfer characteristics and the tensile properties of unidirectional short flax fiber-reinforced composites. The model takes into account of the interfacial shear stiffness, bonding strength between fiber end face and matrix, fiber aspect ratio and fiber volume fraction. 3D finite element models of the composites using a cohesive zone method are used to verify the accuracy of the modified shear-lag model. The fiber tensile strength and the composite tensile elastic modulus are significantly influenced by the interfacial shear stiffness, fiber aspect ratio, and fiber volume fraction. The bonding strength between the fiber end face and the matrix only has an effect when the interfacial shear stiffness is low. The predicted results from the modified shear-lag model show good agreement with the finite element analysis and experimental results in the literature. The modified cohesive shear-lag model provides a simple and effective method for analyzing fiber axial stress, shear stress in the fiber/matrix interface, and tensile elastic modulus of the final composite.

Micromechanical Simulations on Waving and Kinked Natural Fiber-Reinforced Plastic Composites

2008 ◽  
Author(s):  
Yibin Xue ◽  
Scott A. Fletcher ◽  
Kunpeng Wang
Keyword(s):  
Aspect Ratio ◽  
Fiber Volume Fraction ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Fiber Reinforced Plastic ◽  
Fiber Aspect Ratio ◽  
Plastic Composites ◽  
Reinforced Plastic

Micromechanics-based simulations were conducted to evaluate the linear and nonlinear properties of natural fiber-reinforced plastic composites with fibers in various waving and kinked forms. Natural fibers, such as woodfibers and fibers from plants, have length-aspect ratio of longitudinal and transverse at or greater than 20. At such high aspect ratio, the natural fiber normally presents in waving, bending, twisting, kinking morphology in the composites. This paper presents a series of micromechanical simulations to predict the elastic and nonlinear elastic behaviors of natural fiber-reinforced plastic composites (NF-PCs) considering the effects of fiber kinking, waving, and arrangements on the stress-strain relationship. A set of three-dimensional unit cells (UC) were developed to mimic various fiber morphologies with the fiber volume fraction of fifty percent, a typical fiber volume fraction for the natural fiber plastic composites. Periodic displacement boundary conditions were implemented on the UC to simulate a unidirectional strain field. The homogenized anisotropic stress-strain relations for NF-PCs were predicted by postulating nonlinear behavior of plastic matrix and perfect and imperfect interface between the NF and the matrix. Stress distributions in the natural fiber were presented as a function of the fiber aspect ratio and the fiber waving and kinking forms. Even though, the high fiber aspect ratio provides relatively high elastic modulus and nonlinear hardening, it also induces high stresses or stress concentration in the fiber that may result in earlier failure of the fiber when the composites undergone a relatively large deformations (&gt; 4%).

Investigation on Strength of Fiber Reinforced Clay

2011 ◽  
Vol 261-263 ◽  
pp. 957-963 ◽  
Author(s):  
Amin Chegenizadeh ◽  
Hamid Nikraz
Keyword(s):  
Fiber Length ◽  
Natural Fiber ◽  
Fiber Composite ◽  
Fiber Reinforced ◽  
Compression Tests ◽  
Good Tool ◽  
Fiber Reinforced Composite ◽  
Reinforced Composite ◽  
The Subject ◽  
Reinforced Clay

Clay soils and their related behavior has always been the subject of many studies. Recent researches show some interests in investigation of inclusion of randomly distributed fiber in clay. Reinforcing subgarde in pavement systems has always been an issue. This study focuses on effect of fiber inclusion on the strength of subgrade material. Natural fiber was used for this investigation. Fiber contents and length have been changed during these tests. The fiber percentage varied from 0 % (for unreinforced samples) to 3% and fiber length varied from 15mm to 65mm. In addition, as the other alternative 0.5% cement material was put in fiber composite to see the performance of composite. Clay was selected as soil. Triaxial Consolidated Undrained (CU) compression tests were carried out to investigate behavior of the composite under different condition. The fiber length and fiber content found to play important rule on the strength of fiber reinforced composite. Furthermore it was observed that ductility of sample increased by fiber inclusion. Cement percentage also found to be a good tool to stabilize soil composite.

Sign in / Sign up

Export Citation Format

Share Document