scholarly journals MICROSTRUCTURAL CHARACTERISATION FOR POLYCRYSTALLINE NICKEL

2020 ◽  
Author(s):  
Srihari Dodla ◽  
Shashvat Agarwal ◽  
R Tejdeep Reddy ◽  
Saurav Sahu
Keyword(s):  
Heat Treatment ◽  
Surface Roughness ◽  
Compression Test ◽  
Cutting Forces ◽  
Deformation Behaviour ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Polycrystalline Nickel ◽  
Structural Applications ◽  
Nickel 200

Polycrystalline Nickel has very good mechanical properties and excellent corrosion resistance. In this paper, we try to find the suitability of Nickel 200 for structural applications. The compression test on the specimens is carried out in the longitudinal and transverse directions and the difference in the strength in both the directions is studied before and after the heat treatment process. By investigation of the microstructure, the correlation between the deformation behaviour and grain morphology is investigated. The compression test results before the heat treatment reveal that by increasing the strain beyond the elastic limit, the material is anisotropic (up to 4 %). Also, the heat treatment analysis reveals that the sub-grains have occurred in the microstructure. Machining experiments have been performed on Nickel 200 to accomplish proper surface finish and dimensional accuracy. Machining results reveal that the process parameters will have a strong influence on cutting forces and surface roughness. The results showed a significant effect of the cutting speed interaction on cutting forces and surface roughness. An improvement of 38% in cutting forces was detected with increasing the cutting speed from 360 rpm to 450 rpm at constant feed rate (0.12 mm/rev) and depth of cut (0.1 mm). However, the surface roughness was almost constant for the increase in the cutting speed.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

The machinability of Al/B4C composites produced by hot pressing based on reinforcing the element ratio

2016 ◽  
Vol 23 (6) ◽  
pp. 743-750 ◽  
Author(s):  
Ergün Ekici ◽  
Mahmut Gülesin
Keyword(s):  
Surface Roughness ◽  
Wear Mechanism ◽  
Cutting Forces ◽  
Hot Pressing ◽  
Matrix Material ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Reinforcement Ratio ◽  
Depth Of Cut ◽  
Crater Wear

AbstractIn this study, the effects of the particle reinforcement ratio on cutting forces and surface roughness were investigated when milling particle-reinforced metal matrix composite (MMCp) produced by hot pressing with different cutting tools. Alumix 123 alloy as the matrix material and B4C particles with an average size of 27 μm and 5%, 10% and 15% ratio as reinforcing elements were used for the manufacture of composite materials. The experiments were carried out in dry cutting conditions with four different cutting speeds, constant feed rate and depth of cut. Changes depending on the increased reinforcement ratio in cutting forces and surface roughness values were investigated; the effects of 10% B4C reinforced composite on tool wear were also examined. It was observed that cutting forces increased with the increase in cutting speed and particle ratio with carbide cutting tools, and it was seen that the cutting forces on the cutting tools decreased when cutting speed decreased and the cutting forces increased as the reinforcement ratios increased. In addition, with increasing the cutting speed, the surface roughness of the machined surfaces of composite samples increased with the carbide tools, while the cubic boron nitride (CBN) tools have the opposite effect. While it was seen that flank and crater wear occurred on the cemented carbide cutting tools, abrasive, adhesive and other wear mechanism tools in addition to the main wear mechanism, no remarkable flank and crater wear occurred on CBN cutting tools.

Experimental Investigations of Cutting Parameters Influence on Cutting Forces and Surface Roughness of Quartz Glass

2013 ◽  
Vol 641-642 ◽  
pp. 367-370
Author(s):  
Gui Qiang Liang ◽  
Fei Fei Zhao
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Diamond Wheel ◽  
Experimental Investigations ◽  
Depth Of Cut ◽  
Feed Force

Abstract In the present study, an attempt has been made to investigate the effect of cutting parameters (cutting speed, feed rate and depth of cut) on cutting forces (feed force, thrust force and cutting force) and surface roughness in milling of Quartz glas using diamond wheel. The cutting process in the up-cut milling of glass is discussed and the cutting force measured. The cutting force gradually increases with the cutter rotation at the beginning of the cut, and oscillates about a constant mean value after a certain undeformed chip thickness. The results show that cutting forces and surface roughness do not vary much with experimental cutting speed in the range of 55–93 m/min. The suggested models of cutting forces and surface roughness and adequately map within the limits of the cutting parameters considered.

Machining Apprenticeship Based on Experimental Training Practice

2011 ◽  
Vol 692 ◽  
pp. 83-92
Author(s):  
Pedro Jose Arrazola ◽  
A. Villar ◽  
R. Fernández ◽  
J. Aperribay
Keyword(s):  
Surface Roughness ◽  
Power Consumption ◽  
Feed Rate ◽  
Cutting Forces ◽  
Theoretical Calculations ◽  
Cutting Speed ◽  
Machining Process ◽  
Depth Of Cut ◽  
Practical Training ◽  
Input Parameters

This article describes a practical machining training aiming that the students acquire the theoretical-practical knowledge of chip formation process. The training takes place after theoretical lessons of machining processes. Thus, this practice allows strengthening the knowledge gained during the lessons. The practical training lasts for five hours, and the student assisted by the teacher analyses the influence of some machining entry parameters (cutting speed, feed rate...) on exit parameters like: (I) cutting forces and power consumption, (II) surface roughness, and (III) chip typology. The practical session is carried out on an experimental set-up (Lathe CNC Danobar 65) equipped with sensors and devices to measure forces (sensor Kistler 9121) and power consumption. In addition, a portable rugosimeter (Hommelwerke) is employed to perform surface roughness measurements. No especial devices are needed for the chip typology analysis. In the case of cutting forces and power consumption, the following input parameters influences are analysed: feed rate, depth of cut and cutting speed. In the case of surface roughness analysis, the following input parameters influences are analysed: feed rate and nose radius of the cutting insert. Finally, regarding chip typology feed rate and depth of cut are examined. The experimental results are compared with model predictions (theoretical calculations) for the three issues studied. The students have to compare both results: theoretical an empirical and they need to explain the reasons when discrepancies appear. Results obtained during the last years demonstrate the student acquires better knowledge of the machining process, and at the same time realises of the process complexity.

scholarly journals Machinability, Modelling and Statistical Analysis of In-Situ Al–Si–TiB2 Composites

2019 ◽  
Vol 3 (1) ◽  
pp. 28 ◽  
Author(s):  
Jimmy Karloopia ◽  
Shaik Mozammil ◽  
Pradeep Jha
Keyword(s):  
Surface Roughness ◽  
Statistical Analysis ◽  
Tool Wear ◽  
Cutting Forces ◽  
Elevated Temperatures ◽  
Optimization Technique ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Conventional Machining

Aluminum and its alloys have numerous applications in manufacturing, aerospace, and automotive industries. At elevated temperatures, they start to fail in fulfilling their roles and functions. Aluminum-based metal matrix composites (MMCs) are good alternatives for metal and alloys due to their excellent properties. However, the conventional machining of several composites shows complications for a number of reasons, such as high tool wear, poor surface roughness, high machining cost, cutting forces, etc. Numerous studies have already been conducted on the machinability of various MMCs, but the machinability of Al–Si–TiB2 composite is still not well studied. It is of utmost importance that several process parameters of conventional machining are precisely controlled as well as optimized. In this study an effort was made to optimize input parameters such as cutting speed, depth of cut, and feed to obtain well-finished final components with the minimum cutting force and tool wear. These progressions are involved with multiple response characteristics, therefore the exploration of an appropriate multi-objective optimization technique was indeed essential. The performance characteristics of cutting forces and surface roughness were considered for optimization of the machining parameters. Analysis of variance (ANOVA) was employed for the optimization and statistical analysis.

scholarly journals The Effect of Surface Roughness of Low Carbon Steel by Heat Treatment in Turning Operation

2020 ◽  
Author(s):  
Abdullah Tariq AL-Malki ◽  
Basim Khidhir
Keyword(s):  
Heat Treatment ◽  
Surface Roughness ◽  
Carbon Steel ◽  
Feed Rate ◽  
Cutting Speed ◽  
Low Carbon Steel ◽  
Depth Of Cut ◽  
Heating Process ◽  
Low Carbon ◽  
Turning Operation

This research focuses on enhancing the surface roughness of low carbon steel by heat treatment of low carbon steel in turning operation. Heat treatment is mainly used to improve the mechanical properties of materials. Two sets of specimens used during the experiment where each has 5 pieces of mild steel that heat-treated of two-level of temperatures of 650 oC and 900oC. After the heating process of all specimens, it will be exposed to different coolant media which are quenching, normalizing and annealing. A carbide single-point tool, one level of cutting parameters selected as one level of cutting speed and depth of cut and two levels of feed rate used during this research. The results show that specimen quenched by oil bath measures the highest value of the surface roughness of 8.26 µm at 900oC and machined with a feed rate of 0.113 mm. While quenched water specimens show less surface roughness of 4.91µm at 650oC in the same feed rate.

scholarly journals Analysis of Surface Roughness and Cutting Forces in Hard Turning of 42CrMo4 Steel using Taguchi and RSM Method

Mechanika ◽  
2020 ◽  
Vol 26 (3) ◽  
pp. 231-241 ◽  
Author(s):  
Mustafa ÖZDEMİR ◽  
Mehmet Tuncay KAYA ◽  
Hamza Kemal AKYILDIZ
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Forces ◽  
Tangential Force ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Radial Force ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Feed Force

In this study, effects of cutting speed (V), feed rate (f), depth of cut (a) and tool tip radius (R) on  surface roughness (Ra, Rz, and Rt) and cutting forces (radial force (Fx), tangential force (Fy), and feed force (Fz)) in hard finish turning processes of hardened 42CrMo4 (52 HRC) material was investigated experimentally. Taguchi’s mixed level parameter design (L18) is used for the experimental design (2x1,3x3). The signal-to-noise ratio (S/N) was used in the evaluation of test results.  By using Taguchi method, cutting parameters giving optimum surface roughness and cutting forces were determined. Regression analyses are applied to predict surface roughness and cutting forces. Analysis of variance (ANOVA) is used to determine the effects of the machining parameters on surface roughness and cutting forces. According to ANOVA analysis, the most important cutting parameters were found to be feed rate for surface roughness and depth of cut among cutting forces.  By conducting validation experiments, optimization was seen to be applied successfully.

Effect of Process Parameters on Cutting Forces and Surface Roughness in Machining of DSS 2205 Using Taguchi’s Approach

2019 ◽  
Vol 895 ◽  
pp. 26-31
Author(s):  
R. Suresh ◽  
L. Shivaramu ◽  
N.G. Siddesh Kumar ◽  
T.N. Srikantha Dath
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Material Behavior ◽  
Depth Of Cut ◽  
Machined Surface ◽  
Coated Carbide ◽  
Side Flow

In the present study an attempt has been made to investigate the effect of process parameters on surface roughness and cutting forces generation in machining of Duplex Stainless Steel (DSS 2205) grade material with TiN coated carbide tool. Taguchi technique is used for optimizing the process parameters. L27 orthogonal array was used to conduct the experimental trials. Cutting forces recorded using piezo-electric based mill tool dynamometer and surface roughness measured using surface roughness measuring instrument. The obtained results indicated that the cutting force increases with increase in feed rate and depth of cut whereas cutting forces decreases with increase in cutting speed. Surface roughness decreases with increase in cutting speed and low feed rate. Scanning Electroscope Microscopic (SEM) images indicates the feed marks, undeformed material and patches on the machined surface. The formation of material side flow and burrs on the feed marks ridges observed at higher cutting speed, low feed rate and depth of cut. It is mainly due to the material behavior like elastic-plastic deformation of the surface layer. The material side flow causes the considerable deterioration of surface quality of the DSS 2205 steel.

PERFORMANCE OF UNCOATED CARBIDE CUTTING TOOL WHEN MACHINING CAST IRON IN DRY CUTTING CONDITION

2009 ◽  
Vol 23 (06n07) ◽  
pp. 1796-1802 ◽  
Author(s):  
A. G. JAHARAH ◽  
C. H. CHE HASSAN ◽  
M. J. GHAZALI ◽  
A. B. SULONG ◽  
M. Z. OMAR ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cast Iron ◽  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Dry Cutting ◽  
Carbide Cutting Tool ◽  
Cutting Speeds

This paper presents the performance of uncoated carbide cutting tool when machining cast iron in dry cutting conditions. Experiments were conducted at various cutting speeds, feed rates, and depths of cut according to Taguchi method design of experiment using a standard orthogonal array L 9(34). The effects of cutting speeds (100-146 m/min), feed rates (0.20-0.35 mm/tooth) and depths of cut (1.0-2.0 mm) on the tool life, surface roughness and cutting forces were evaluated using ANOVA. Results showed that the effects of cutting speed, depth of cut and the feed rate were similar affecting the failure of the carbide cutting tools within the range of tested machining parameters. The contribution of cutting speed, feed rate, and depth of cut in controlling the tool life were 32.12%, 38.56% and 29.32% respectively. Whereas, the cutting speed was the main factor influencing the average surface roughness (Ra) value followed by feed rate. These factors contribute 60.53% and 35.59% respectively to the Ra value. On the other hand, cutting forces generated were greatly influenced by the depth of cut (66.52%) and the feed rate (32.6%). Cutting speed was found insignificant in controlling the generated cutting forces.

Experimental investigations of cutting parameters’ influence on cutting forces and surface roughness in turning of Inconel alloy X-750 with biodegradable vegetable oil

2015 ◽  
Vol 231 (9) ◽  
pp. 1516-1527 ◽  
Author(s):  
Ahmadreza Hosseini Tazehkandi ◽  
Mohammadreza Shabgard ◽  
Farid Pilehvarian ◽  
Nakisa Farshfroush
Keyword(s):  
Surface Roughness ◽  
Vegetable Oil ◽  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Inconel Alloy ◽  
Coated Carbide

Nickel-based Inconel X-750 superalloy is widely applied in aerospace industry and manufacturing of gas turbine blades, power generators and heat exchangers due to its exclusive properties. As a consequence of low heat transfer coefficient and work-hardening properties, this alloy is known as a poorly machinable alloy. In this work, effect of machining parameters (cutting speed, feed rate and depth of cut) on cutting forces and surface roughness was investigated during turning of Inconel alloy X-750 with coated carbide tool. In order to meet the demands of the environment-friendly cutting processes and human health, biodegradable vegetable oil (BioCut 4600) was selected as the cutting fluid. The results were analyzed using response surface methodology and statistical analysis of variance, and mathematical models for cutting forces and surface roughness were proposed. Results indicated that feed rate and cutting speed were the most effective parameters on the surface roughness. However, depth of cut was the most effective parameter on cutting forces in comparison with cutting speed and feed rate. Eventually, in order to achieve the main aims of industrial production in large amounts and green manufacturing, the ranges for the best cutting conditions were presented.

Sign in / Sign up

Export Citation Format

Share Document