scholarly journals Evaluation of some Properties of Polyester Based Hybrid Composites Produced From Luffa-Bananna Fibres

2019 ◽  
Vol 1 ◽  
pp. 265-274
Author(s):  
K K Ikpambese ◽  
S Aye ◽  
A W Onuh
Keyword(s):  
Water Absorption ◽  
Interior Design ◽  
Hybrid Composites ◽  
Raw Materials ◽  
Loss Modulus ◽  
Maximum Level ◽  
Dynamic Mechanical Properties ◽  
Damping Factor ◽  
Dynamic Mechanical ◽  
Increasing Temperature

This study presents the evaluation of the mechanical, physical and dynamic mechanical properties of luffa-banana fibre reinforced polyester hybrid composites. The luffa fibre and banana fibres were extracted from luffa plant and banana stem respectively by manual stripping into strands. The luffa and banana fibres were then blended in the ratio of 50:50 for the production of the hybrid composites using hand lay-up method. Polyester-resin was used as binder and the percentages of luffa-banana fibres used were 3, 5, 6, and 9 %. The tensile strength, impact strength, flexural strength, density, water absorption, and the dynamic mechanical analysis (DMA) (storage modulus, loss modulus damping factor) of the produced luffa-banana hybrid composites were evaluated. The results of the density and water absorption obtained varied from 0.84-1.23 g/cm3 and 0 - 0.35 % respectively. The tensile and impact strengths (3.46 - 9.27 MPa and 0.66-3.26 J/cm2) of the produced hybrid composites were observed to increase with increasing fibre content from 3 - 6 % and decreased at 9 %. The results of DMA revealed that loss modulus of the hybrid composites and pure polyester were found to increase with increasing temperature up to glass transition temperature and then decreased. The damping factor was observed to increase with increasing temperature and goes at maximum level in transition region and while decreasing the in rubbery region. The properties of the produced hybrid luffa-banana composites showed that luffa and banana fibres can be used in synergy as raw materials for composites manufacture. As the properties evaluated were in agreement with standard composites used as interior design of cars.

Partial replacement of synthetic fibres by natural fibres in hybrid composites and its effect on monotonic properties

2019 ◽  
pp. 152808371987884 ◽  
Author(s):  
Suhad D Salman
Keyword(s):  
Mechanical Properties ◽  
Hybrid Composites ◽  
Loss Modulus ◽  
Dynamic Mechanical Properties ◽  
Partial Replacement ◽  
Damping Factor ◽  
Jute Fibre ◽  
Carbon Fibres ◽  
Dynamic Mechanical ◽  
Increasing Temperature

Owing to the high cost of carbon fibres and a necessity for finding alternatives that environmentally friendly, a portion of carbon fibres was substituted by woven jute fibre, with various stacking sequences for military applications. Hot press was used to fabricate the composite and hybrid samples of jute/carbon fibres reinforced polyvinyl butyral film using as a layer. Dynamic mechanical experiments (DMA) were conducted with more focus on the stacking sequences of jute and carbon, with increasing temperature. Results showed that the carbon/jute/carbon (H1) hybrid has the highest storage modulus and loss modulus values compared with other hybrids. Significantly, placing woven jute fibre at the outer layers and carbon fibres at the inner layers provided lower dynamic mechanical properties than that of the hybrids with placing jute at the inner layers. Besides, the damping factor shifts to higher temperatures by hybridization of jute fibres compared with carbon composite. Additionally, glass transition temperature (Tg) obtained from the damping curve and loss modulus exhibits a temperature between 129 and 180℃ for all composites, in withstanding dynamic loads. The dynamic mechanical properties were observed to be decreased with increasing temperature for all laminated composites. From results, it could be deduced that it is possible to reduce amount of carbon fibres in different composites industries with woven jute, thus providing less both cost and harmful environment.

scholarly journals Dynamic Mechanical Properties of Hybrid Layered Silicates/Kaolin Geopolymer Filler in Epoxy Composites

2017 ◽  
Vol 54 (3) ◽  
pp. 543-545 ◽  
Author(s):  
Yusrina Mat Daud ◽  
Kamarudin Hussin ◽  
Azlin Fazlina Osman ◽  
Che Mohd Ruzaidi Ghazali ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Speed ◽  
Hybrid Composites ◽  
Loss Modulus ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Layered Silicates ◽  
Epoxy Composites ◽  
Damping Factor ◽  
Dynamic Mechanical

Preparation epoxy based hybrid composites were involved kaolin geopolymer filler, organo-montmorillonite at 3phr by using high speed mechanical stirrer. A mechanical behaviour of neat epoxy, epoxy/organo-montmorillonite and its hybrid composites containing 1-8phr kaolin geopolymer filler was studied upon cyclic deformation (three-point flexion mode) as the temperature is varies. The analysis was determined by dynamic mechanical analysis (DMA) at frequency of 1.0Hz. The results then expressed in storage modulus (E�), loss modulus (E�) and damping factor (tan d) as function of temperature from 40 oC to 130oC. Overall results indicated that E�, E�� and Tg increased considerably by incorporating optimum 1phr kaolin geopolymer in epoxy organo-montmorillonite hybrid composites.

PLA-coated sisal fibre-reinforced polyester composite: Water absorption, static and dynamic mechanical properties

2018 ◽  
Vol 53 (1) ◽  
pp. 65-72 ◽  
Author(s):  
MK Gupta ◽  
Rohit Singh
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Loss Modulus ◽  
Alkali Treatment ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Static Properties ◽  
Physical Treatment ◽  
Sisal Fibre ◽  
Dynamic Mechanical

In the present work, a novel physical treatment (PLA coating) of sisal fibres and its influence on the water absorption, static and dynamic mechanical properties of its composites has been presented. The treated sisal fibres were used consisted of alkali treatment and PLA coating to fabricate its polyester-based composites by hand lay-up technique keeping constant fibres content as 20 wt.% . Water absorption analysis was carried out in terms of water uptake (%), and sorption, diffusion and permeability coefficient. In addition, static properties were examined in terms of tensile, flexural and impact test, and dynamic mechanical analysis was performed in terms of storage modulus [Formula: see text], loss modulus [Formula: see text], damping [Formula: see text] and glass transition temperature [Formula: see text]. It was reported that the PLA-coated sisal composites showed the best performance in water absorption, mechanical and dynamic mechanical properties than pure sisal and alkali-treated sisal composites. There were 33%, 49%, 48%, and 27% improvement in water resistance, tensile strength, flexural strength and impact strength, respectively, of PLA-coated sisal composites as compared to that of pure sisal composite.

scholarly journals Effect of Short Fiber Reinforcement on Mechanical Properties of Hybrid Phenolic Composites

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Sembian Manoharan ◽  
Bhimappa Suresha ◽  
Govindarajulu Ramadoss ◽  
Basavaraj Bharath
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Loss Modulus ◽  
Basalt Fiber ◽  
Barium Sulphate ◽  
Dynamic Mechanical Properties ◽  
Damping Factor ◽  
X Ray ◽  
Weight Percentage ◽  
Dynamic Mechanical

Fiber plays an important role in determining the hardness, strength, and dynamic mechanical properties of composite material. In the present work, enhancement of viscoelastic behaviour of hybrid phenolic composites has been synergistically investigated. Five different phenolic composites, namely, C1, C2, C3, C4, and C5, were fabricated by varying the weight percentage of basalt and aramid fiber, namely, 25, 20, 15, 10, and 5% by compensating with barium sulphate (BaSO4) to keep the combined reinforcement concentration at 25 wt%. Hardness was measured to examine the resistance of composites to indentation. The hardness of phenolic composites increased from 72.2 to 85.2 with increase in basalt fiber loading. Composite C1 (25 wt% fiber) is 1.2 times harder than composite C5. Compression test was conducted to find out compressive strength of phenolic composites and compressive strength increased with increase in fiber content. Dynamic mechanical analysis (DMA) was carried out to assess the temperature dependence mechanical properties in terms of storage modulus (E′), loss modulus (E′′), and damping factor (tan δ). The results indicate great improvement of E′ values and decrease in damping behaviour of composite upon fiber addition. Further X-ray powder diffraction (XRD) and energy-dispersive X-ray (EDX) analysis were employed to characterize the friction composites.

scholarly journals Enhancement of Mechanical and Dynamic Mechanical Properties of Hydrophilic Nanoclay Reinforced Polylactic Acid/Polycaprolactone/Oil Palm Mesocarp Fiber Hybrid Composites

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Chern Chiet Eng ◽  
Nor Azowa Ibrahim ◽  
Norhazlin Zainuddin ◽  
Hidayah Ariffin ◽  
Wan Md. Zin Wan Yunus ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Oil Palm ◽  
Hybrid Composites ◽  
Loss Modulus ◽  
Impact Resistance ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Dynamic Mechanical ◽  
The Fourier Transform

In previous studies, the effect of the addition of 1 wt% hydrophilic nanoclay on polylactic acid (PLA)/polycaprolactone (PCL)/oil palm mesocarp fiber (OPMF) biocomposites was investigated by tensile properties, thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). The current studies focus on the effect of addition of 1 wt% hydrophilic nanoclay on mechanical (flexural and impact properties) and dynamic mechanical properties of composites. The composites were characterized by the Fourier transform infrared spectroscopy (FTIR) and dynamic mechanical analysis (DMA). FTIR spectra show that peak shifting occurs when 1 wt% hydrophilic nanoclay was added to composites. The addition of 1 wt% hydrophilic nanoclay successfully improves the flexural properties and impact resistance of the biocomposites. The storage modulus of biocomposites was decreased when nanoclay was added which indicates that the stiffness of biocomposites was reduced. The loss modulus curve shows that the addition of nanoclay shift twotgin composites become closer to each other which indicates that the incorporation of nanoclay slightly compatibilizes the biocomposites. Tanδindicated that hybrid composites dissipate less energy compared to biocomposites indicate that addition of clay to biocomposites improves fiber/matrix adhesion. Water sorption test shows that the addition of nanoclay enhances water resistance of composites.

Thermal and dynamic mechanical analysis of hybrid jute/sisal fibre reinforced epoxy composite

2016 ◽  
Vol 232 (9) ◽  
pp. 743-748 ◽  
Author(s):  
MK Gupta
Keyword(s):  
Thermal Properties ◽  
Storage Modulus ◽  
Hybrid Composites ◽  
Loss Modulus ◽  
Dynamic Mechanical Properties ◽  
Decomposition Temperature ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Sisal Fibre ◽  
Dynamic Mechanical

The aim of the present study is to investigate the dynamic mechanical and thermal properties of hybrid jute/sisal fibre reinforced epoxy composites. The hybrid composites were prepared by hand layup technique having total fibre loading of 30% by weight with different weight ratios of jute and sisal fibres. Dynamic mechanical properties such as storage modulus ([Formula: see text]), loss modulus ([Formula: see text]) and damping ([Formula: see text]) were investigated in the temperature range of 30–200 ℃. The thermal stability of the prepared composites was studied using thermogravimetric analysis. Other thermal properties such as glass transition temperature ( Tg), crystallization temperature ( Tc) and decomposition temperature ( Td) were also obtained by differential scanning calorimetry. The results indicated a positive effect of hybridization in terms of increase in dynamic mechanical and thermal properties. Storage modulus, loss modulus and Tg were found to be higher for hybrid composite having a higher percentage of jute fibres.

scholarly journals Dynamic mechanical analysis of nylon 6 fiber-reinforced acrylonitrile butadiene rubber composites

2021 ◽  
pp. 096739112110461
Author(s):  
C Rajesh ◽  
P Divia ◽  
S Dinooplal ◽  
G Unnikrishnan ◽  
E Purushothaman
Keyword(s):  
Mechanical Properties ◽  
Storage Modulus ◽  
Loss Modulus ◽  
Dynamic Mechanical Properties ◽  
Damping Factor ◽  
Butadiene Rubber ◽  
Bonding Agents ◽  
Fiber Loading ◽  
Dynamic Mechanical ◽  
Acrylonitrile Butadiene Rubber

Dynamic mechanical properties of polymeric materials are of direct relevance to a range of unique polymer applications. The aim of the study is to investigate the dynamic mechanical properties of composites of short nylon 6 fiber with acrylonitrile butadiene rubber (NBR). The storage modulus (G′), loss modulus (G″), and the damping factor (tan δ) have been analyzed with reference to the effects of fiber loading, curing systems, and bonding agents over a range of temperature and at varying frequencies. The storage modulus increases with increment in fiber loading, whereas loss modulus and damping factor decrease. The glass transition temperature shifts to higher temperature upon increment in fiber loading. Dicumyl peroxide (DCP)–cured composites show higher storage modulus and lower damping than the corresponding sulfur-cured one. The addition of hexa-resorcinol and phthalic anhydride as bonding agents enhances the dynamic mechanical properties of the composites. The experimental results have been evaluated by comparing with Einstein, Guth, and Nielsen models.

The static and dynamic mechanical properties of kenaf/glass fibre reinforced hybrid composites

2018 ◽  
Vol 5 (9) ◽  
pp. 095304 ◽  
Author(s):  
Sivakumar Dhar Malingam ◽  
Lin Feng Ng ◽  
Kin How Chan ◽  
Kathiravan Subramaniam ◽  
Mohd Zulkefli Selamat ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Glass Fibre ◽  
Hybrid Composites ◽  
Dynamic Mechanical Properties ◽  
Dynamic Mechanical ◽  
Glass Fibre Reinforced

scholarly journals Influence of Thermally-Accelerated Aging on the Dynamic Mechanical Properties of HTPB Coating and Crosslinking Density-Modified Model for the Payne Effect

Polymers ◽  
2020 ◽  
Vol 12 (2) ◽  
pp. 403 ◽  
Author(s):  
Yongqiang Du ◽  
Jian Zheng ◽  
Guibo Yu
Keyword(s):  
Mechanical Properties ◽  
Aging Time ◽  
Loss Modulus ◽  
Accelerated Aging ◽  
Crosslinking Density ◽  
Dynamic Mechanical Properties ◽  
Maximum Elongation ◽  
Solid Rocket Motor ◽  
Payne Effect ◽  
Dynamic Mechanical

Hydroxyl terminated polybutadiene (HTPB) coating is widely used in a solid rocket motor, but an aging phenomenon exists during long-term storage, which causes irreversible damage to the performance of this HTPB coating. In order to study the effect of aging on the dynamic mechanical properties of the HTPB coating, the thermally-accelerated aging test was carried out. The variation of maximum elongation and crosslinking density with aging time was obtained, and a good linear relationship between maximum elongation and crosslinking density was found by correlation analysis. The changing regularity of dynamic mechanical properties with aging time was analyzed. It was found that with the increase of aging time, Tg of HTPB coating increased, Tα, tan β and tan α decreased, and the functional relationships between the loss factor parameters and crosslinking density were constructed. The storage modulus and loss modulus of HTPB coating increased with the increase of aging time, and decreased with the increase of pre-strain. The aging enhanced the Payne effect of HTPB coating, while the pre-strain had a weakening effect. In view of the Payne effect of HTPB coating, the crosslinking density was introduced into Kraus model as aging evaluation parameter, and the crosslinking density modified models with and without pre-strain were established. The proposed models can effectively solve the problem that the Kraus model has a poor fitting effect under the condition of small strain (generally less than 1%) and on the loss modulus, which have improved the correlations between the fitting results and the test results.

Sign in / Sign up

Export Citation Format

Share Document